Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface

This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.

This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Data contained within "Append IEs" command (QLINK_CMD_MGMT_SET_APPIE)
duplicates QTN_TLV_ID_IE_SET TLV. Convert the command to use that TLV
instead.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

"IE set" TLV carries the same information as
qlink_event_scan_result::frame_type. Convert the event to make use of
TLV and drop frame_type member.
While at it, make qlink_event_scan_result structure alignement-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Specifying frame type for "IE set" TLV will allow to use several
TLVs in a single message.
Modify users accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Supported WiFi operation modes are now identified per-band based on
HT/VHT capabilities of each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Information on which HT/VHT capabilities can be overridden is reported
per-MAC by wireless device.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.

To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.

While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The configuration of the IEs for probe requests was done in a P2P
related function, which is not very obvious. Moving it to
.scan callback function, ie. brcmf_cfg80211_scan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The field struct brcmf_cfg80211_info::active_scan is set to true upon
initializing the driver instance, but it is never changed so simply
get rid of it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The function brcmf_cfg80211_escan() is only called by brcmf_cfg80211_scan()
so there is no reason to split in two function especially since the latter
does not do an awful lot.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Minor cleanup using provided macro to convert milliseconds interval
to jiffies in brcmf_cfg80211_escan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The function brcmf_cfg80211_escan() was always called with a non-null
request parameter and null pointer for this_ssid parameter. Clean up
the function removing the dead code path.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Disable arp and nd offload to allow all packets sending to host.
Reported-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The firmware uses a mailbox to communicate to the host what is going
on. In the driver we validate the bit received. Various people seen
the following message:

 brcmfmac: brcmf_sdio_hostmail: Unknown mailbox data content: 0x40012

Bit 4 is cause of this message, but this actually indicates the firmware
has halted. Handle this bit by giving a more meaningful error message.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Variable framelen is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:

drivers/net/wireless/zydas/zd1201.c:234:3: warning: Value stored
to 'framelen' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The pointer dev is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:

drivers/net/wireless/intersil/orinoco/orinoco_usb.c:1468:2: warning:
Value stored to 'dev' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Pointer sta_priv is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:

drivers/net/wireless/intel/iwlegacy/4965-rs.c:2163:2: warning: Value
stored to 'sta_priv' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

cfg_cmd is initialized to zero and this value is never read, instead
it is over-written in the start of a do-while loop. Remove the
redundant initialization. Cleans up clang warning:

drivers/net/wireless/realtek/rtlwifi/core.c:1750:22: warning: Value
stored to 'cfg_cmd' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

tid_data is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:

drivers/net/wireless/realtek/rtlwifi/base.c:1581:2: warning: Value
stored to 'tid_data' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The calculation of ppsc->last_wakeup_time is not y2038-safe, but
the variable is not used at all, so we can simply drop it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

do_gettimeofday() is deprecated and slower than necessary for the purpose
of reading the seconds. This changes rtl_op_suspend/resume to use
ktime_get_real_seconds() instead, which is simpler and avoids confusion
about whether it is y2038-safe or not.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.

Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

8822be checks H2CQ by int_d, so we extend to four ISR.
Also, irq_mask is extended to four.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When the driver for the RTL8822BE is added, it will need an ID for
further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

With the RTL8822BE, an H2C tx queue is added to download FW and special
data. This change implements the support code in rtl_pci.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The number of TX/RX BD desc for 8822BE is 512.
The TX/RX BD architecture of 8822BE is the same as 8192EE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In several places, the code assigns a variable inside an "if" or "case"
block, but uses it only once. The code is simplified by eliminating
the extraneous variable. With this change, one level of indenting is
saved.

This patch does not cause any functional changes in the binary code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Checkpatch.pl reports a number of formatting problems in this source
file. None of the changes cause any functional changes in the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Checkpatch.pl reports a number of formatting problems in this header
file. None of the changes cause any functional changes in the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

iwlwifi updates

* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;

Roman Gushchin says:

====================
eBPF-based device cgroup controller

This patchset introduces an eBPF-based device controller for cgroup v2.

Patches (1) and (2) are a preparational work required to share some code
  with the existing device controller implementation.
Patch (3) is the main patch, which introduces a new bpf prog type
  and all necessary infrastructure.
Patch (4) moves cgroup_helpers.c/h to use them by patch (4).
Patch (5) implements an example of eBPF program which controls access
  to device files and corresponding userspace test.

v3:
  Renamed constants introduced by patch (3) to BPF_DEVCG_*

v2:
  Added patch (1).

v1:
  https://lkml.org/lkml/2017/11/1/363
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test for device cgroup controller.

The test loads a simple bpf program which logs all
device access attempts using trace_printk() and forbids
all operations except operations with /dev/zero and
/dev/urandom.

Then the test creates and joins a test cgroup, and attaches
the bpf program to it.

Then it tries to perform some simple device operations
and checks the result:

  create /dev/null (should fail)
  create /dev/zero (should pass)
  copy data from /dev/urandom to /dev/zero (should pass)
  copy data from /dev/urandom to /dev/full (should fail)
  copy data from /dev/random to /dev/zero (should fail)
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The purpose of this move is to use these files in bpf tests.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cgroup v2 lacks the device controller, provided by cgroup v1.
This patch adds a new eBPF program type, which in combination
of previously added ability to attach multiple eBPF programs
to a cgroup, will provide a similar functionality, but with some
additional flexibility.

This patch introduces a BPF_PROG_TYPE_CGROUP_DEVICE program type.
A program takes major and minor device numbers, device type
(block/character) and access type (mknod/read/write) as parameters
and returns an integer which defines if the operation should be
allowed or terminated with -EPERM.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is non-functional change to prepare the device cgroup code
for adding eBPF-based controller for cgroups v2.

The patch performs the following changes:
1) __devcgroup_inode_permission() and devcgroup_inode_mknod()
   are moving to the device-cgroup.h and converting into static inline.
2) __devcgroup_check_permission() is exported.
3) devcgroup_check_permission() wrapper is introduced to be used
   by both existing and new bpf-based implementations.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename device type and access type constants defined in
security/device_cgroup.c by adding the DEVCG_ prefix.

The reason behind this renaming is to make them global namespace
friendly, as they will be moved to the corresponding header file
by following patches.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2017-11-04

This series includes:

From Huy: dscp to priority mapping for Ethernet packet.

===================================================
First six patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.

Firmware interface:
Mellanox firmware provides two control knobs for this feature:
  QPTS register allow changing the trust state between dscp and
  pcp mode. The default is pcp mode. Once in dscp mode, firmware will
  route the packet based on its dscp value if the dscp field exists.

  QPDPM register allow mapping a specific dscp (0 to 63) to a
  specific priority (0 to 7). By default, all the dscps are mapped to
  priority zero.

Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.

The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.

When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.

When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
===================================================

Plus to the dscp series, some small misc changes are include as well:

From Inbar, Ethtool msglvl support and some debug prints in DCBNL logic
From Or Gerlitz, Enlarge the NIC TC offload table size
From Rabie, Initialize destination_flow struct to 0
From Feras, Add inner TTC table to IPoIB flow steering
From Tal, Enable CQE based moderation on TX CQ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: ethtool and related improvements

Dirk van der Merwe says:

This patch series throws a couple of loosely related items into a single
series.

Patch 1: Clang compilation fix reported by
  Matthias Kaehlcke <mka@chromium.org>

Patch 2: Driver can now do MAC reinit on load when there has been a
  media override set in the NSP.

Patch 3: Refactor the nfp_app_reprs_set API.

Patch 4: Similar to vNICs, representors must be able to deal with media
  override changes in the NSP.

Patch 5: Since representors can now handle media overrides, we can
  allocate the get/set link ndo's to them.

Patch 6 & 7: Add support for FEC mode modification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in the driver ethtool ops to modify the NFP FEC modes.

The FEC modes can be set for vNIC associated with physical ports or
for MAC representor netdevs.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement helpers to determine and modify FEC modes via the NSP.
The NSP advertises FEC capabilities on a per port basis and provides
support for:
* Auto mode selection
* Reed Solomon
* BaseR
* None/Off
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>