- 02 Oct, 2018 40 commits
-
-
Grigor Tovmasyan authored
Added interrupt handler for WkupAlert interrupt. This interrupt should initiate Remote Wake up. Acked-by:
Minas Harutyunyan <hminas@synopsys.com> Signed-off-by:
Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com>
-
Grigor Tovmasyan authored
WKUP_ALERT interrupt should be unmask when lpm mode is enabled. This interrupt is asserted when the device is in L1 for the duration mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to initiate Remote wake up so that the device resumes in time in order not to lose sync with the host frame number. Acked-by:
-
Grigor Tovmasyan authored
Added dwc2_gadget_program_ref_clk function to program GREFCLK register in device mode. Acked-by:
-
Grigor Tovmasyan authored
Added ref_clk_per and sof_cnt_wkup_alert parameters in dwc2_core_params struct and set default values. Acked-by:
-
Grigor Tovmasyan authored
New registers were added to dwc otg core. GREFCLK - This register used to control ref_clk parameters. GINTSTS2 - New WKUP_ALERT interrupt was added. GINTMSK2 - Mask register for GINTSTS2. Acked-by:
-
Grigor Tovmasyan authored
In service interval based scheduling target (u)frame must be set as a last frame in this the service interval. Acked-by:
-
Grigor Tovmasyan authored
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c. This function will be used to calculate descriptor frame number field value. For service interval mode frame number in descriptor should point to last (u)frame in the interval. Acked-by:
-
Grigor Tovmasyan authored
Added core parameter for service interval based scheduling. Acked-by:
-
Grigor Tovmasyan authored
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support service interval based scheduling. Acked-by:
-
Yoshihiro Shimoda authored
This patch adds support for R-Car E3. This SoC needs to release the PLL reset by the UGCTRL register like R-Car D3. So, this patch adds a usbhs_of_match entry for this SoC with "USBHS_TYPE_RCAR_GEN3_WITH_PLL". Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Yoshihiro Shimoda authored
This patch adds bindings for r8a77990 (R-Car E3). Reviewed-by:
-
Yoshihiro Shimoda authored
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2 value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car Gen3 SoCs. Reviewed-by:
-
Yoshihiro Shimoda authored
This reverts commit cd14247d. R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore. Reviewed-by:
-
Andreas Pape authored
Via p_chmask/c_chmask the user can define whether uac2 shall support playback and/or capture. This has only effect on the created ALSA device, but not on the USB descriptor. This patch adds playback/capture descriptors dependent on that parameter. Signed-off-by:
Andreas Pape <apape@de.adit-jv.com> Signed-off-by:
Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by:
-
Alan Stern authored
The gadget documentation doesn't state clearly whether a gadget driver's ->disconnect() callback should be invoked when the D+ pullup is turned off. Some UDC drivers do this and some don't. This patch settles the issue by making the core function usb_gadget_disconnect() issue the callback, so that UDC drivers don't need to worry about it. A description of the new behavior is added to the function's kerneldoc. Also, the patch removes a few superseded callbacks from other core routines. Future patches will remove the ->disconnect() calls from the UDC drivers that make them, as they are now unnecessary. Until all those patches are merged gadget drivers may receive extra ->disconnect() callbacks, but this should be harmless. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Faisal Mehmood authored
'optimizations' was misspelled as 'optmizations'. Fixed it. It is a coding style change which should have no impact on runtime execution of code. Signed-off-by:
Faisal Mehmood <f.m3hm00d@gmail.com> Signed-off-by:
-
Rob Herring authored
The name is always non-NULL and then is not used anywhere in this function, so remove it. Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Felipe Balbi <balbi@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-usb@vger.kernel.org Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Nicholas Mc Guire authored
The original implementation from commit b504882d ("USB: add Freescale high-speed USB SOC device controller driver") returned NULL on failure and an allocated + initialized struct fsl_udc on success. The current code introduced in commit 4365831d ("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register") only provides partial initialization as well as returning 0 on success and -1 on failures. The function documentation is updated accordingly. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Fixes: 4365831d ("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register") Signed-off-by:
-
Nicholas Mc Guire authored
The allocation with fsl_alloc_request() and kmalloc() were unchecked fixed this up with a NULL check and appropriate cleanup. Additionally udc->ep_qh_size was reset to 0 on failure of allocation. Similar udc->phy_mode is initially 0 (as udc_controller was allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well so that this function is side-effect free on failure. Not clear if this is necessary or sensible as fsl_udc_release() probably can not be called if fsl_udc_probe() failed - but it should not hurt. Signed-off-by:
-
Chunfeng Yun authored
The vbus rise & fall interrupts are used to enable and disable U3 function of device automatically, this cause some issues when class driver is initialized as deactivated, and will skip over software-controlled connect by pullup(), but UDC wants to keep disconnect until usb_gadget_activate() is called which calls pullup() if needed. So we disable vbus rise & fall interrupts and just use pullup() to enable & disable U3 function, and reset mtu3 state when disconnect instead when vbus fall. Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by:
-
Yoshihiro Shimoda authored
R-Car Gen3 needs to enable clocks of both host and peripheral. Since [eo]hci-platform disables the reset(s) when the drivers are removed, renesas_usbhs driver doesn't work correctly. To fix this issue, this patch adds multiple clocks management on this renesas_usbhs driver. Signed-off-by:
-
Yoshihiro Shimoda authored
R-Car Gen3 needs to enable clocks of both host and peripheral. Otherwise, other side device cannot work correctly. So, this patch adds a property of clock-names for R-Car Gen3 as an optional. Signed-off-by:
-
Yoshihiro Shimoda authored
R-Car Gen3 needs to deassert resets of both host and peripheral. Since [eo]hci-platform is possible to assert the reset(s) when the probing failed, renesas_usbhs driver doesn't work correctly regardless of finished probing. To fix this issue, this patch adds reset_control on this renesas_usbhs driver. Signed-off-by:
-
Thinh Nguyen authored
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint command. Current implementation only save and restore GUSB2PHYCFG.SUSPHY configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY settings. Restore them after the command is completed. DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2 Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
-
Fabrice Gasnier authored
When using external vbus supply regulator, it should be enabled synchronously with PWR bit in HPRT register. This also fixes unbalanced use of this optional regulator (This can be reproduced easily when unbinding the driver). Fixes: 531ef5eb ("usb: dwc2: add support for host mode external vbus supply") Tested-by:
Artur Petrosyan <arturp@synopsys.com> Acked-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by:
-
Fabrice Gasnier authored
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be called with interrupts disabled as it might sleep. This is seen with DEBUG_ATOMIC_SLEEP=y. Fixes: 531ef5eb ("usb: dwc2: add support for host mode external vbus supply") Tested-by:
-
Fabrice Gasnier authored
There's a race with root hub resume, when using external vbus supply. Root hub gets resumed, but runtime pm autosuspend runs as external vbus supply isn't enabled. So, host never exit from power down properly. Initialize vbus external supply before, rater that after hub resume. Fixes: 531ef5eb ("usb: dwc2: add support for host mode external vbus supply") Tested-by:
-
Fabrice Gasnier authored
Move devm_regulator_get_optional() call to probe routine. This avoids 'vbus-supply' regulator to be requested lots of times, upon each call to dwc2_vbus_supply_init(), e.g. like with runtime pm. Fixes: 531ef5eb ("usb: dwc2: add support for host mode external vbus supply") Tested-by:
-
Arnd Bergmann authored
Like the omap back-end, we get a link error with CONFIG_EXTCON=m when building the qcom back-end into the kernel: drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe': dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle' dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier' dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state' Do the same thing as OMAP and add an explicit dependency on EXTCON. Fixes: a4333c3a ("usb: dwc3: Add Qualcomm DWC3 glue driver") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Alexandre Belloni authored
The at91sam9rl PMC is not quite the same as the at91sam9g45 one and now has its own compatible string. Add support for that. Fixes: 217bace8e548 ("ARM: dts: fix PMC compatible") Acked-by:Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Jia-Ju Bai authored
The driver may sleep in an interrupt handler. The function call path (from bottom to top) in Linux-4.17 is: [FUNC] fotg210_ep_queue(GFP_KERNEL) drivers/usb/gadget/udc/fotg210-udc.c, 744: fotg210_ep_queue in fotg210_get_status drivers/usb/gadget/udc/fotg210-udc.c, 768: fotg210_get_status in fotg210_setup_packet drivers/usb/gadget/udc/fotg210-udc.c, 949: fotg210_setup_packet in fotg210_irq (interrupt handler) To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC. If possible, spin_unlock() and spin_lock() around fotg210_ep_queue() can be also removed. This bug is found by my static analysis tool DSAC. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
-
Minas Harutyunyan authored
Disabling all EP's allow to reset EP's to initial state. On disconnect disable all EP's instead of just killing all requests. Because of some platform didn't catch disconnect event, same stuff added to dwc2_hsotg_core_init_disconnected() function when USB reset detected on the bus. Changed from version 1: Changed lock acquire flow in dwc2_hsotg_ep_disable() function. Signed-off-by:
-
Marek Szyprowski authored
DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30 clocks enabled all the time the driver does any access to DWC3 registers, otherwise external abort happens. So far DWC3 hardware module worked with samsung,exynos5250-dwusb3 compatible only by luck when built into kernel: all DRD30 clocks were left enabled by bootloader and later kept enabled by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as a module or performed system suspend/resume cycle, external abort happened. This patch finally fixes this issue. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
Add per-variant list of clocks and manage them all together in the single array. This is a preparation for adding new variants of Exynos SoCs. No functional changes for existing Exynos SoCs. Signed-off-by:
-
Marek Szyprowski authored
All supported Exynos variants provide respective generic PHY framework based drivers for controlling USB PHYs, so there is no point creating fake USB PHYs based on platform devices. While removing useless code, remove calls to runtime PM, which have no effect. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in dev_dbg message Acked-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Nathan Chancellor authored
Clang warns when multiple pairs of parentheses are used for a single conditional statement. drivers/usb/gadget/udc/mv_udc_core.c:188:33: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) { ~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~ drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: remove extraneous parentheses around the comparison to silence this warning while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) { ~ ^ ~ drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: use '=' to turn this equality comparison into an assignment while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) { ^~ = 1 warning generated. Link: https://github.com/ClangBuiltLinux/linux/issues/120Signed-off-by:Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Josh Abraham authored
This patch removes a set but unused variable in hcd.c. Fixes gcc warning: variable ‘data_fifo’ set but not used [-Wunused-but-set-variable] Acked-by:
Joshua Abraham <j.abraham1776@gmail.com> Signed-off-by:
-
Yoshihiro Shimoda authored
This reverts commit 8ada211d. R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore. In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode by using the phy-rcar-gen3-usb2 driver. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistakes in debug warning messages Signed-off-by:
-
