Even for the mock i915 device, we need to initialise the
drm.mode_config, as we may ultimately query whether there are any KMS
users deep in the bowels of some paths (e.g. eviction). As we initialise
drm.mode_config we must cleanup after ourselves!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171209210835.32609-1-chris@chris-wilson.co.uk

Before accessing the GGTT we must flush the PTE writes and make them
visible to the chipset, or else the indirect access may end up in the
wrong page. In commit 3497971a ("agp/intel: Flush chipset writes
after updating a single PTE"), we noticed corruption of the uploads for
pwrite and for capturing GPU error states, but it was presumed that the
explicit calls to intel_gtt_chipset_flush() were sufficient for the
execbuffer path. However, we have not been flushing the chipset between
the PTE writes and access via the GTT itself.

For simplicity, do the flush after any PTE update rather than try and
batch the flushes on a just-in-time basis.

References: 3497971a ("agp/intel: Flush chipset writes after updating a single PTE")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208214616.30147-1-chris@chris-wilson.co.uk

Since the seqno information shown from i915_interrupt_info is just a
small subset of i915_engine_info, remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171209104418.4223-2-chris@chris-wilson.co.uk

The per-engine seqno info is now available from
debugfs/i915_engine_info obsoleting debugfs/i915_seqno_info, so remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171209104418.4223-1-chris@chris-wilson.co.uk

Comparing the state tested by intel_engine_is_idle() and printed by
intel_engine_dump(), the only bit not shown is whether or not the device
is wedged. Add that little bit of information to the pretty printer so
that if the engine fails to idle we can see why.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208012303.25504-5-chris@chris-wilson.co.uk

Since a global reset affects the engine, include that along side the
per-engine reset counter when pretty printing the engine state in
intel_engine_dump().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208012303.25504-4-chris@chris-wilson.co.uk

Now that we have a common engine state pretty printer, we can use that
instead of the adhoc information printed when we miss a breadcrumb.

v2: Rearrange intel_engine_disarm_breadcrumbs() to avoid calling
intel_engine_dump() under the rb spinlock (Mika) and to pretty-print the
error state early so that we include the full list of waiters.
v3: Pass missed breadcrumb msg to pretty-printer as the header
v4: Preserve DRM_DEBUG_DRIVER filtering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208012303.25504-3-chris@chris-wilson.co.uk

Pass in a format string (and args) to specify the header to be emitted
along with the engine state when pretty-printing. This allows the header
to be emitted inside the drm_printer stream, so sharing the same prefix
and output characteristics (e.g. debug level and filtering).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208012303.25504-2-chris@chris-wilson.co.uk

When printing the execlist ports, we first print the ELSP header then
follow it with the pretty-printed request. Since switching to
drm_printer and show the output via printk, it automatically appends a
newline to each call (unlike the old seq_printf output). To avoid the
unwanted line break, construct the ELSP request header in a temporary
buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208012303.25504-1-chris@chris-wilson.co.uk

Chris requested this backmerge for a reconciliation on
drm_print.h between drm-misc-next and drm-intel-next-queued
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

When intel_modeset_setup_plane_state() fails drop the local framebuffer
reference before jumping to the error, otherwise we leak the framebuffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: edde3617 ("drm/i915: Use atomic state to obtain load detection crtc, v3.")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171207220025.22698-1-chris@chris-wilson.co.uk

Even fbc isn't using this stuff anymore, so time to remove it.

Cleaning up one small piece of the atomic conversion cruft at the time
...

Quick explanation on why the plane->fb assignment is ok to delete: The
core code takes care of the refcounting and legacy ->fb pointer
updating, but drivers are allowed to update it ahead of time. Most
legacy modeset drivers did that as part of their set_config callback
(since that's how the legacy/crtc helpers worked). In i915 we only
need that to make the fbc code happy.

v2: don't nuke the assignement of intel_crtc->config, I accidentally
set CI ablaze :-) Spotted by Maarten. And better explain why nuking
the ->fb assignement shouldn't set off alarm bells.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171207143202.6021-1-daniel.vetter@ffwll.ch

It seems that the DMC likes to transition between the DC states a lot when
there are no connected displays (no active power domains) during command
submission.

This activity on DC states has a negative impact on the performance of the
chip with huge latencies observed in the interrupt handlers and elsewhere.
Simple tests like igt/gem_latency -n 0 are slowed down by a factor of
eight.

Work around it by introducing a new power domain named,
POWER_DOMAIN_GT_IRQ, associtated with the "DC off" power well, which is
held for the duration of command submission activity.

CNL has the same problem which will be addressed as a follow-up. Doing
that requires a fix for a DC6 context corruption problem in the CNL DMC
firmware which is yet to be released.

v2:
 * Add commit text as comment in i915_gem_mark_busy. (Chris Wilson)
 * Protect macro body with braces. (Jani Nikula)

v3:
 * Add dedicated power domain for clarity. (Chris, Imre)
 * Commit message and comment text updates.
 * Apply to all big-core GEN9 parts apart for Skylake which is pending DMC
   firmware release.

v4:
 * Power domain should be inner to device runtime pm. (Chris)
 * Simplify NEEDS_CSR_GT_PERF_WA macro. (Chris)
 * Handle async DMC loading by moving the GT_IRQ power domain logic into
   intel_runtime_pm. (Daniel, Chris)
 * Include small core GEN9 as well. (Imre)

v5
 * Special handling for async DMC load is not needed since on failure the
   power domain reference is kept permanently taken. (Imre)

v6:
 * Drop the NEEDS_CSR_GT_PERF_WA macro since all firmwares have now been
   deployed. (Imre, Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v5)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Imre: Add note about applying the WA on CNL as a follow-up]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205132854.26380-1-tvrtko.ursulin@linux.intel.com

Currently on every submission, we recalculate the ELSP register offset
for the engine, after chasing the pointers to find the iomem base. Since
this is fixed for the lifetime of the driver, record the offset in the
execlists struct.

In practice the difference is negligible, it just happens to remove 27
bytes of eyesore pointer dancing from next to the hottest instruction
(which is itself due to stalling for a cache miss) in perf profiles of
the execlists_submission_tasklet().

v2: Trim off one more elsp local.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171207222434.17686-1-chris@chris-wilson.co.uk

In quite a few places, we have a list iteration over the vma on an
object that only want to inspect GGTT vma. By construction, these are
placed at the start of the list, so we have copied that knowledge into
many callsites. Pull that knowledge back to i915_vma.h and provide a
for_each_ggtt_vma() to tidy up the code.

v2: Add a backreference from vma_create() to remind ourselves why we put
ggtt vma at the head of the obj->vma_list (and ppgtt vma at the tail).
v3: Fixup s/vma/V/
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171207211407.31549-1-chris@chris-wilson.co.uk

[airlied: fix conflict in intel_dsi.c]

drm-intel-next-2017-12-01:

- Init clock gate fix (Ville)
- Execlists event handling corrections (Chris, Michel)
- Improvements on GPU Cache invalidation and context switch (Chris)
- More perf OA changes (Lionel)
- More selftests improvements and fixes (Chris, Matthew)
- Clean-up on modules parameters (Chris)
- Clean-up around old ringbuffer submission and hw semaphore on old platforms (Chris)
- More Cannonlake stabilization effort (David, James)
- Display planes clean-up and improvements (Ville)
- New PMU interface for perf queries... (Tvrtko)
- ... and other subsequent PMU changes and fixes (Tvrtko, Chris)
- Remove success dmesg noise from rotation (Chris)
- New DMC for Kabylake (Anusha)
- Fixes around atomic commits (Daniel)
- GuC updates and fixes (Sagar, Michal, Chris)
- Couple gmbus/i2c fixes (Ville)
- Use exponential backoff for all our wait_for() (Chris)
- Fixes for i915/fbdev (Chris)
- Backlight fixes (Arnd)
- Updates on shrinker (Chris)
- Make Hotplug enable more robuts (Chris)
- Disable huge pages (TPH) on lack of a needed workaround (Joonas)
- New GuC images for SKL, KBL, BXT (Sagar)
- Add HW Workaround for Geminilake performance (Valtteri)
- Fixes for PPS timings (Imre)
- More IPS fixes (Maarten)
- Many fixes for Display Port on gen2-gen4 (Ville)
- Retry GPU reset making the recover from hang more robust (Chris)

* tag 'drm-intel-next-2017-12-01' of git://anongit.freedesktop.org/drm/drm-intel: (101 commits)
  drm/i915: Update DRIVER_DATE to 20171201
  drm/i915/cnl: Mask previous DDI - PLL mapping
  drm/i915: Remove unsafe i915.enable_rc6
  drm/i915: Sleep and retry a GPU reset if at first we don't succeed
  drm/i915: Interlaced DP output doesn't work on VLV/CHV
  drm/i915: Pass crtc state to intel_pipe_{enable,disable}()
  drm/i915: Wait for pipe to start on i830 as well
  drm/i915: Fix vblank timestamp/frame counter jumps on gen2
  drm/i915: Fix deadlock in i830_disable_pipe()
  drm/i915: Fix has_audio readout for DDI A
  drm/i915: Don't add the "force audio" property to DP connectors that don't support audio
  drm/i915: Disable DP audio for g4x
  drm/i915/selftests: Wake the device before executing requests on the GPU
  drm/i915: Set fake_vma.size as well as fake_vma.node.size for capture
  drm/i915: Tidy up signed/unsigned comparison
  drm/i915: Enable IPS with only sprite plane visible too, v4.
  drm/i915: Make ips_enabled a property depending on whether IPS is enabled, v3.
  drm/i915: Avoid PPS HW/SW state mismatch due to rounding
  drm/i915: Skip switch-to-kernel-context on suspend when wedged
  drm/i915/glk: Apply WaProgramL3SqcReg1DefaultForPerf for GLK too
  ...

UAPI Changes:

- Add "panel orientation" property to DRM to indicate orientation of the
panel vs the device's casing (Hans de Goede)

Core Changes:

- misc doc and bug fixes

Driver Changes:

- sun4i: Many improvements to the DE driver like multi-plane support and
YUV formats (Jernej Skrabec)

* tag 'drm-misc-next-2017-12-07' of git://anongit.freedesktop.org/drm/drm-misc: (50 commits)
  drm/sun4i: Fix uninitialized variables in vi layer
  drm/fb-helper: Fix potential NULL pointer dereference
  gpu: drm: stm: Adopt SPDX identifiers
  gpu: drm: sti: Adopt SPDX identifiers
  drm/fsl-dcu: Use drm_mode_config_helper_suspend/resume()
  drm/sun4i: Wire in DE2 YUV support
  drm/sun4i: Expand DE2 scaler lib with YUV support
  drm/sun4i: Add DE2 definitions for YUV formats
  drm/sun4i: Add DE2 CSC library
  drm/sun4i: Add CCSC property to DE2 configuration
  drm/sun4i: Add support for HW scaling to DE2
  drm/sun4i: Add scaler configuration to DE2 mixers
  drm/sun4i: Add support for DE2 VI planes
  drm/sun4i: Reorganize UI layer code in DE2
  drm/sun4i: Add support for all HW supported DE2 RGB formats
  drm/sun4i: Add multi plane support to DE2 driver
  drm/sun4i: Move interlace related code in DE2
  drm/sun4i: Move channel size related code in DE2
  drm/sun4i: Move line width setting in DE2
  drm/sun4i: Use values calculated by atomic check
  ...

As writes through the GTT and GGTT PTE updates do not share the same
path, they are not strictly ordered and so we must explicitly flush the
indirect writes prior to modifying the PTE. We do track outstanding GGTT
writes on the object itself, but since the object may have multiple GGTT
vma, that is overly coarse as we can track and flush individual vma as
required.

Whilst here, update the GGTT flushing behaviour for Cannonlake.

v2: Hard-code ring offset to allow use during unload (after RCS may have
been freed, or never existed!)

References: https://bugs.freedesktop.org/show_bug.cgi?id=104002Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171206124914.19960-2-chris@chris-wilson.co.uk

Originally we translated from the object to the vma by walking
obj->vma_list to find the matching vm (for user lookups). Now we process
user lookups using the rbtree, and we only use obj->vma_list itself for
maintaining state (e.g. ensuring that all vma are flushed or rebound).
As such maintenance needs to go on beyond the user's awareness of the
vma, defer removal of the vma from the obj->vma_list from i915_vma_close()
to i915_vma_destroy()

Fixes: 5888fc9e ("drm/i915: Flush pending GTT writes before unbinding")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104155Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171206124914.19960-1-chris@chris-wilson.co.ukReviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

min_scale and max_scale in sun8i_vi_layer_atomic_check() can be used
without initialization.

Fix that.

Fixes: b862a648 ("drm/sun4i: Add support for HW scaling to DE2")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171206152603.25937-1-jernej.skrabec@siol.net

fb_helper is being dereferenced before it is null checked,
hence there is a potential null pointer dereference.

Fix this by moving the pointer dereference after fb_helper
has been null checked.

This issue was detected with the help of Coccinelle.

Fixes: c777990f ("drm/fb-helper: Handle function NULL argument")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205174628.GA31189@embeddedor.com

First feature request for 4.16.  Highlights:
- RV and Vega header cleanups
- TTM operation context support
- 48 bit GPUVM fixes for Vega/RV
- More smatch fixes
- ECC support for vega10
- Resizeable BAR support
- Multi-display sync support in DC
- SR-IOV fixes
- Various scheduler improvements
- GPU reset fixes and vram lost tracking
- Clean up DC/powerplay interfaces
- DCN display fixes
- Various DC fixes

* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux: (291 commits)
  drm/radeon: Use drm_fb_helper_lastclose() and _poll_changed()
  drm/amdgpu: Use drm_fb_helper_lastclose() and _poll_changed()
  drm/amd/display: Use drm_fb_helper_poll_changed()
  drm/ttm: swap consecutive allocated pooled pages v4
  drm/amdgpu: fix amdgpu_sync_resv v2
  drm/ttm: swap consecutive allocated cached pages v3
  drm/amd/amdgpu: set gtt size according to system memory size only
  drm/amdgpu: Get rid of dep_sync as a seperate object.
  drm/amdgpu: allow specifying vm_block_size for multi level PDs v2
  drm/amdgpu: move validation of the VM size into the VM code
  drm/amdgpu: allow non pot VM size values
  drm/amdgpu: choose number of VM levels based on VM size
  drm/amdgpu: unify VM size handling of Vega10 with older generation
  drm/amdgpu: fix amdgpu_vm_num_entries
  drm/amdgpu: fix VM PD addr shift
  drm/amdgpu: correct vce4.0 fw config for SRIOV (V2)
  drm/amd/display: Don't call dm_log_to_buffer directly in dc_conn_log
  drm/amd/display: Add dm_logger_append_va API
  drm/ttm: Use a static string instead of an array of char *
  drm/amd/display: remove usage of legacy_cursor_update
  ...

This driver can use drm_fb_helper_lastclose() in its .lastclose function.
It can also use drm_fb_helper_output_poll_changed() as its
.output_poll_changed callback.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This driver can use drm_fb_helper_lastclose() in its .lastclose function.
It can also use drm_fb_helper_output_poll_changed() as its
.output_poll_changed callback.
Remove the unused driver implementations.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This driver can use drm_fb_helper_output_poll_changed() as its
.output_poll_changed callback.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When we detect consecutive allocation of pages swap them to avoid
accidentally freeing them as huge page.

v2: use swap
v3: check if it's really the first allocated page
v4: don't touch the loop variable
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes a bug introduced by AMDGPU_GEM_CREATE_EXPLICIT_SYNC. We still need
to wait for pipelined moves in the shared fences list.

v2: fix typo
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Andres Rodriguez <andresx7@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When we detect consecutive allocation of pages swap them to avoid
accidentally freeing them as huge page.

v2: use swap
v3: check if it's really the first allocated page
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Instead mark fence as explicit in it's amdgpu_sync_entry.

v2:
Fix use after free bug and add new parameter description.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch allows specifying the vm_block_size even when multi level
page directories are active.

v2: fix signed/unsigned compare warning
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This moves validation of the VM size parameter into amdgpu_vm_adjust_size().
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The VM size actually doesn't need to be a power of two.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This allows us limiting the VM size for testing even of Vega10.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

One function to rule them all.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The block size only affects the leave nodes, everything else is fixed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The block size only affects the leave nodes, everything else is fixed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1. program vce 4.0 fw with 48 bit address
2. correct vce 4.0 fw stack and date offset
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

dm_log_to_buffer logs unconditionally, so calling it directly resulted
in the main message being logged even when the event type isn't enabled
in the event mask.

To fix this, use the new dm_logger_append_va API.

Fixes spurious messages like

 [drm] {1920x1200, 2080x1235@154000Khz}

in dmesg when a mode is set.

v2:
* Use new dm_logger_append_va API, fixes incorrect va_list usage in v1
* Just use and decrease entry.buf_offset to get rid of the trailing
  newline
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Same as dm_logger_append, except it takes a va_list instead of a
variable number of arguments. dm_logger_append is now a minimal wrapper
around dm_logger_append_va.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>