- 28 Jun, 2006 40 commits
-
-
Jim Cromie authored
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable, they are generic, and can be moved 'verbatim' to the nsc_gpio common-support module. After the move, various symbols are renamed to update 'scx200_' to 'nsc_', and headers are adjusted accordingly. Signed-off-by:
Jim Cromie <jim.cromie@gmail.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Jim Cromie authored
Add the nsc_gpio common-support module as an empty shell. Next patch starts the migration of the common gpio support routines. Signed-off-by:
-
Jim Cromie authored
Now actually call the gpio operations thru the vtable. Signed-off-by:
-
Jim Cromie authored
Abstract the gpio operations into a new nsc_gpio_ops vtable. Signed-off-by:
-
Jim Cromie authored
[PATCH] chardev: GPIO for SCx200 & PC-8736x: refactor scx200_probe to better segregate _gpio initialization Pull shadow-reg initialization into separate function now, rather than doing it 2x later (scx200, pc8736x). When we revisit 2nd drvr below, it will be to reimplement an init function, rather than another refactor. Signed-off-by:
-
Jim Cromie authored
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output goes to the log, like all other INFO messages in the original driver. Giving the user control over the feedback they 'need' is construed to be a user-friendly feature, and allows us (later) to dial down many INFO messages to DEBUG log-level. Signed-off-by:
-
Jim Cromie authored
Shrink scx200_gpio_dump() to a single printk with ternary ops. The function is still ifdef'd out, this is corrected in next patch, when it is actually used. The patch 'inadvertently' changed loglevel from DEBUG to INFO. This is Good, because in next patch, its wired to a 'command' which the user can invoke when they want. When they do so, its because they want INFO to support their developement effort, and we want to give it to them without compiling a DEBUG version of the driver. Signed-off-by:
-
Jim Cromie authored
Per kernel headers, device minor numbers are unsigned ints. Do the same in this driver. Signed-off-by:
-
Jim Cromie authored
Add a platform-device to scx200_gpio, and use its struct device dev member (ie: devp) in dev_dbg() once. There are 2 alternatives here (Im soliciting guidance/commentary): - use isa_device, if/when its added to the kernel. - alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio, and the (to be added) nsc_gpio module can use it. Since the available devp is in 'grandparent', this seems like too much 'action at a distance'. Signed-off-by:
-
Jim Cromie authored
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are limited to initialization calls from module init, ie: cdev_init, cdev_add, *_chrdev_region, mkdev. Signed-off-by:
-
Jim Cromie authored
GPIO SUPPORT FOR SCx200 & PC8736x The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x chips. Its handy for the Soekris.com net-4801, which has both chips. These patches have been seen recently on Kernel-Mentors, and then Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has been incorporated. Thanks Jesper ! Its also gone to soekris-tech@soekris.com for possible testing by linux folks, I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll see.. Device-file & Sysfs The driver preserves the existing device-file interface, including the write/cmd set, but adds v to 'view' the pin-settings & configs by inducing, via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status, but it sticks to the syslog approach, conservatively. Allowing users to voluntarily trigger logging is good, it gives them a familiar way to confirm their app's control & use of the pins, and I've thus reduced the pin-mode-updates from dev_info to dev_dbg. I've recently bolted on a proto sysfs interface for both new drivers. Im not including those patches here; they (the patch + doc-pre-patch) are still quite raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a proper vetting is needed. Since this patchset is much bigger than my previous ones, Id like to keep things simpler, and address it 1st, before bolting on more stuff. The driver-split The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a common pin-architecture (same pin features, with same bits controlling), but with different addressing mechanics and port organizations. The vintage driver expresses the pin capabilities with pin-mode commands [OoPpTt],etc that change the pin configurations, and since the 2 chips share pin-arch, we can reuse the read(), write() commands, once the implementation is suitably adjusted. The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio operations, then adjusts fileops.write() code to invoke operations via that vtable. Driver specific open()s set private_data to the vtable so its available for use by write(). The vtable gets the gpio_dump() too, since its user-friendly, and (could be construed as) part of the current device-file interface. To support use of dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both scx200 & pc8736x _gpio drivers. heres how the pins are presented in syslog: [ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE [ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO nsc_gpio.c: new file is new home of several file-ops methods, which are modified to get their vtable from filp->private_data, and use it where needed. scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this vtable). A driver-spcific open() initializes filp->private_data with the vtable. Once the split is clean, and the scx200_gpio driver is working, we copy and modify the function and variable names, and rework the access-method bodies for the different addressing scheme. Heres a working overview of the patchset: # series file for GPIO # Spring Cleaning gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments # API Modernization gpio-scx/patch.api26 # what I learned from LDD3 gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg() gpio-scx/patch.unsigned-minor # fix to match std practice # Debuggability gpio-scx/patch.dump-diet # shrink gpio_dump() gpio-scx/patch.viewpins # add new 'command' to call dump() gpio-scx/patch.init-refactor # pull shadow-register init to sub # Access-Abstraction (add vtable) gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio gpio-scx/patch.nscgpio-shell # add empty driver for common-fops # move code under abstraction gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt # gpio-scx/patch.add-DEBUG # enable all dev_dbg()s # Cleanups # finish printk -> dev_dbg() etc gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too, gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg() # gpio-scx/patch.pin-config-view # another 'c' 'command' # gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet now) gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in pc87* # post KMentors-post patches .. gpio-scx/patch.mutexes # use mutexes for config-locks gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd gpio-scx/patch.kconfig # add stuff for kbuild # TBC # combine api26 with pdev, which is just one step. # merge c&v commands to single do-all-fn # delay viewpins, dump-diet should also un-ifdef it too. diff.sys-gpio-rollup-1 This patch: Removed editor format-control comments, and used scripts/Lindent to clean up whitespace, then deleted the bogus chunks :-( Signed-off-by:
-
Chandra Seetharaman authored
Make use the of newly defined hotplug version of cpu_notifier functionality wherever appropriate. Signed-off-by:
Chandra Seetharaman <sekharan@us.ibm.com> Cc: Ashok Raj <ashok.raj@intel.com> Signed-off-by:
-
Chandra Seetharaman authored
Define new macros register_hotcpu_notifier() and unregister_hotcpu_notifier() that redefines register_cpu_notifier() and unregister_cpu_notifier() for use only when HOTPLUG_CPU is defined. Signed-off-by:
-
Chandra Seetharaman authored
Make notifier_calls associated with cpu_notifier as __cpuinit. __cpuinit makes sure that the function is init time only unless CONFIG_HOTPLUG_CPU is defined. [akpm@osdl.org: section fix] Signed-off-by:
-
Chandra Seetharaman authored
Make notifier_blocks associated with cpu_notifier as __cpuinitdata. __cpuinitdata makes sure that the data is init time only unless CONFIG_HOTPLUG_CPU is defined. Signed-off-by:
-
Chandra Seetharaman authored
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined). So, cpu_notifier functionality need to be available only at init time. This patch makes register_cpu_notifier() available only at init time, unless CONFIG_HOTPLUG_CPU is defined. This patch exports register_cpu_notifier() and unregister_cpu_notifier() only if CONFIG_HOTPLUG_CPU is defined. Signed-off-by:
-
Chandra Seetharaman authored
This patch reverts notifier_block changes made in 2.6.17 Signed-off-by:
-
Chandra Seetharaman authored
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a band-aid solution to solve that problem. In the process, i undid all the changes you both were making to ensure that these notifiers were available only at init time (unless CONFIG_HOTPLUG_CPU is defined). We deferred the real fix to 2.6.18. Here is a set of patches that fixes the XFS problem cleanly and makes the cpu notifiers available only at init time (unless CONFIG_HOTPLUG_CPU is defined). If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run time. This patch reverts the notifier_call changes made in 2.6.17 Signed-off-by:
-
Sonny Rao authored
We need to serialize access to the global rtc_idr even in this error path. Signed-off-by:
Sonny Rao <sonny@burdell.org> Acked-by:
Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Alan Cox authored
There are two locking sets involved. One locks the board mappings and the other is the tty open/close locking. The low level code was clearly designed to be ported to OS's with spin locks already so pretty much comes out in the wash Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
akpm@osdl.org authored
Corey Minyard <minyard@acm.org> The kthread used to speed up polling for IPMI was using udelay in its busy-wait polling loop when the lower-level state machine told it to do a short delay. This just used CPU and didn't help scheduling, thus causing bad problems with other tasks. Call schedule() instead. Signed-off-by:
Corey Minyard <minyard@acm.org> Acked-by:
Matt Domsch <Matt_Domsch@dell.com> Signed-off-by:
-
Paul E. McKenney authored
Add operations for the call_rcu_bh() variant of RCU. Also add an rcu_batches_completed_bh() function, which is needed by rcutorture. Signed-off-by:
Paul E. McKenney <paulmck@us.ibm.com> Signed-off-by:
-
Paul E. McKenney authored
Add an ops vector to rcutorture, and add the ops for Classic RCU. Update the rcutorture documentation to reflect slight change to the dmesg formats. Signed-off-by:
-
Paul E. McKenney authored
This just catches the RCU torture documentation up with the recent fixes that test RCU for architectures that turn of the scheduling-clock interrupt for idle CPUs and the addition of a SUCCESS/FAILURE indication, fixing up an obsolete comment as well. Signed-off-by:
-
Randy Dunlap authored
Fix kernel-doc parameters in kernel/ Warning(/var/linsrc/linux-2617-g9//kernel/auditsc.c:1376): No description found for parameter 'u_abs_timeout' Warning(/var/linsrc/linux-2617-g9//kernel/auditsc.c:1420): No description found for parameter 'u_msg_prio' Warning(/var/linsrc/linux-2617-g9//kernel/auditsc.c:1420): No description found for parameter 'u_abs_timeout' Warning(/var/linsrc/linux-2617-g9//kernel/acct.c:526): No description found for parameter 'pacct' Signed-off-by:
Randy Dunlap <rdunlap@xenotime.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Paul Fulghum authored
Fix TCSBRK comment to prevent confusion or accidental removal. Signed-off-by:
Paul Fulghum <paulkf@microgate.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
-
Evgeniy Dushistov authored
Add missed ufsi->i_dir_start_lookup initialization in ufs_read_inode in UFS2 case. Also it cleans ufs_read_inode function to prevent such kind of situation in the future: it move depend on UFS type parts of code into separate functions and leaves in ufs_read_inode only generic code. It cleans code and avoids duplication. Signed-off-by:
Evgeniy Dushistov <dushistov@mail.ru> Signed-off-by:
-
Atsushi Nemoto authored
Signed-off-by:
Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by:
-
Vladimir V. Saveliev authored
generic_file_buffered_write() prefaults in user pages in order to avoid deadlock on copying from the same page as write goes to. However, it looks like there is a problem when write is vectored: fault_in_pages_readable brings in current segment or its part (maxlen). OTOH, filemap_copy_from_user_iovec is called to copy number of bytes (bytes) which may exceed current segment, so filemap_copy_from_user_iovec switches to the next segment which is not brought in yet. Pagefault is generated. That causes the deadlock if pagefault is for the same page write goes to: page being written is locked and not uptodate, pagefault will deadlock trying to lock locked page. [akpm@osdl.org: somewhat rewritten] Cc: Neil Brown <neilb@suse.de> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: <stable@kernel.org> Signed-off-by:
-
David Woodhouse authored
We include config.h on the compiler command line. There's no need for it to be included again. Signed-off-by:
David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
Ingo Molnar authored
locking init cleanups: - convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK() - convert rwlocks in a similar manner this patch was generated automatically. Motivation: - cleanliness - lockdep needs control of lock initialization, which the open-coded variants do not give - it's also useful for -rt and for lock debugging in general Signed-off-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
Arjan van de Ven <arjan@linux.intel.com> Signed-off-by:
-
Adrian Bunk authored
- add a proper prototype for the following global function: - buffer_init() - make the following needlessly global function static: - end_buffer_async_write() Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Randy Dunlap authored
Add more poison values to include/linux/poison.h. It's not clear to me whether some others should be added or not, so I haven't added any of these: ./include/linux/libata.h:#define ATA_TAG_POISON 0xfafbfcfdU ./arch/ppc/8260_io/fcc_enet.c:1918: memset((char *)(&(immap->im_dprambase[(mem_addr+64)])), 0x88, 32); ./drivers/usb/mon/mon_text.c:429: memset(mem, 0xe5, sizeof(struct mon_event_text)); ./drivers/char/ftape/lowlevel/ftape-ctl.c:738: memset(ft_buffer[i]->address, 0xAA, FT_BUFF_SIZE); ./drivers/block/sx8.c:/* 0xf is just arbitrary, non-zero noise; this is sorta like poisoning */ Signed-off-by:
-
Randy Dunlap authored
Update two drivers to use poison.h. Signed-off-by:
-
Randy Dunlap authored
Localize poison values into one header file for better documentation and easier/quicker debugging and so that the same values won't be used for multiple purposes. Use these constants in core arch., mm, driver, and fs code. Signed-off-by:
Matt Mackall <mpm@selenic.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andi Kleen <ak@muc.de> Signed-off-by:
-
Ingo Molnar authored
Move the i386 VDSO down into a vma and thus randomize it. Besides the security implications, this feature also helps debuggers, which can COW a vma-backed VDSO just like a normal DSO and can thus do single-stepping and other debugging features. It's good for hypervisors (Xen, VMWare) too, which typically live in the same high-mapped address space as the VDSO, hence whenever the VDSO is used, they get lots of guest pagefaults and have to fix such guest accesses up - which slows things down instead of speeding things up (the primary purpose of the VDSO). There's a new CONFIG_COMPAT_VDSO (default=y) option, which provides support for older glibcs that still rely on a prelinked high-mapped VDSO. Newer distributions (using glibc 2.3.3 or later) can turn this option off. Turning it off is also recommended for security reasons: attackers cannot use the predictable high-mapped VDSO page as syscall trampoline anymore. There is a new vdso=[0|1] boot option as well, and a runtime /proc/sys/vm/vdso_enabled sysctl switch, that allows the VDSO to be turned on/off. (This version of the VDSO-randomization patch also has working ELF coredumping, the previous patch crashed in the coredumping code.) This code is a combined work of the exec-shield VDSO randomization code and Gerd Hoffmann's hypervisor-centric VDSO patch. Rusty Russell started this patch and i completed it. [akpm@osdl.org: cleanups] [akpm@osdl.org: compile fix] [akpm@osdl.org: compile fix 2] [akpm@osdl.org: compile fix 3] [akpm@osdl.org: revernt MAXMEM change] Signed-off-by:
Arjan van de Ven <arjan@infradead.org> Cc: Gerd Hoffmann <kraxel@suse.de> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Zachary Amsden <zach@vmware.com> Cc: Andi Kleen <ak@muc.de> Cc: Jan Beulich <jbeulich@novell.com> Signed-off-by:
-
James Bottomley authored
The following [PATCH] Clean up and refactor i386 sub-architecture setup Doesn't quite work, since it leaves out an include of asm/io.h, without which the use of inb/outb in the setup file won.t work. This corrects that and also removes a spurious acpi reference that apparently crept in ages ago but should never have been there. Signed-off-by:
James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by:
-
James Bottomley authored
Commit 1e9f28fa ("[PATCH] sched: new sched domain for representing multi-core") incorrectly made SCHED_SMT and some of the structures it uses dependent on SMP. However, this is wrong, the structures are only defined if X86_HT, so SCHED_SMT has to depend on that as well. The patch broke voyager, since it doesn't provide any of the multi-core or hyperthreading structures. Signed-off-by:
-
Aleksey Gorelov authored
Commit c3ff8ec3 ("[PATCH] i386: Don't miss pending signals returning to user mode after signal processing") meant that vm86 interrupt/signal handling got broken for the case when vm86 is called from kernel space. In this scenario, if signal is pending because of vm86 interrupt, do_notify_resume/do_signal exits immediately due to user_mode() check, without processing any signals. Thus, resume_userspace handler is spinning in a tight loop with signal pending and TIF_SIGPENDING is set. Previously everything worked Ok. No in-tree usage of vm86() from kernel space exists, but I've heard about a number of projects out there which use vm86 calls from kernel, one of them being this, for instance: http://dev.gentoo.org/~spock/projects/vesafb-tng/ The following patch fixes the issue. Signed-off-by:
Aleksey Gorelov <aleksey_gorelov@phoenix.com> Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Roland McGrath <roland@redhat.com> Signed-off-by:
-
Chuck Ebbert authored
Using C code for current_thread_info() lets the compiler optimize it. With gcc 4.0.2, kernel is smaller: text data bss dec hex filename 3645212 555556 312024 4512792 44dc18 2.6.17-rc6-nb-post/vmlinux 3647276 555556 312024 4514856 44e428 2.6.17-rc6-nb/vmlinux ------- -2064 Signed-off-by:Chuck Ebbert <76306.1226@compuserve.com> Signed-off-by:
-
