- 16 Oct, 2007 40 commits
-
-
Bartlomiej Zolnierkiewicz authored
It has been obsoleted since 1 Nov 2004, is valid only when used together with "ide=nodma" kernel parameter (which makes no sense) and only for aec62xx, cmd64x, cs5220, generic, hpt366, sl82c105, tc86c001 and triflex host drivers. Acked-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Bartlomiej Zolnierkiewicz authored
This code doesn't use pci_assign_resource() and ide_get_or_set_dma_base() uses pci_resource_start() to get DMA base address so it has no chance of working. Moreover this belongs to PCI quirks (in case somebody would like to fix it). Acked-by:
-
Bartlomiej Zolnierkiewicz authored
While at it: - make struct pci_device_id tables const - use PCI_DEVICE_ID_ITE_8213 define in it8213.c - fix comment in generic.c Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
Clear prefetch and postwrite for ATAPI devices instead of depending on BIOS. Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Don't force PIO4 when programming UDMA mode (suggested by Sergei). Acked-by:
-
Adrian Bunk authored
noautodma can now be unexported. Signed-off-by:
Adrian Bunk <bunk@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Adrian Bunk authored
static code mustn't be exported. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend on BIOS for programming device/controller for DMA. Set it in cy82c693, generic, ns87415, opti621 and trm290 host drivers. * Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520 host driver. * Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag. * Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check implementations. Fix all places checking for presence of ->ide_dma_check hook to check for ->ide_dma_on instead. * Remove no longer needed code from config_drive_for_dma(). * Make ide_tune_dma() static. v2: * Fix config_drive_for_dma() return values. * Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding dummy config_drive_for_dma() inline. * Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check(). * Fix init_hwif_it8213() comment. There should be no functionality changes caused by this patch. Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets ->autotune this change shouldn't have any other effect than bringing ide-pmac driver in-line with other host drivers wrt ->ide_dma_check implementation. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Since ide-cris allows separate PIO and DMA timings, and ide-cris always sets ->autotune this change shouldn't have any other effect than bringing ide-cris driver in-line with other host drivers wrt ->ide_dma_check implementation. Cc: Mikael Starvik <starvik@axis.com> Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Since sl82c105 re-programs DMA/PIO timings for DMA enable/disable, and sets ->autotune this change shouldn't have any other effect than bringing sl82c105 driver in-line with other host drivers wrt ->ide_dma_check implementation. Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
* Add PIO autotune fallback to ->ide_dma_check. Since cs5530/sc1200 allow separate PIO and DMA timings, and cs5530/sc1200 always set ->autotune this change shouldn't have any other effect than bringing these drivers in-line with other host drivers wrt ->ide_dma_check implementations. * Fix ->ide_dma_check to return "-1" if DMA cannot be set. * Bump driver version. Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set drive->autotune so PIO is always tuned anyway and in some cases we _really_ need to re-tune PIO because PIO and DMA timings are shared. Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Several host drivers used to reset drive->init_speed in their ->ide_dma_check implementations which resulted in incorrect init speed being reported to the user, fix it. Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
* Remove needless setting of drive->using_dma from auide_dma_check(). * Split off auide_mdma_filter() from auide_dma_check(). * Use ide_tune_dma() in auide_dma_check(), this fixes following issues: - device's DMA capability bit not being checked - device not being checked against generic DMA blacklist - transfer mode not being set on device/host * Add PIO autotune fallback to auide_dma_check(). Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
Acked-by:
-
Bartlomiej Zolnierkiewicz authored
* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode(). * ATI controllers allow separate PIO and DMA timings so remove programming of PIO modes from atiixp_set_dma_mode(). Also remove no longer needed atiixp_dma_2_pio() helper. * SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable support for SWDMA modes for now. * Enable support for MWDMA0 mode. * Bump driver version. Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
Acked-by:
Mikael Starvik <starvik@axis.com> Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Acked-by:
-
Bartlomiej Zolnierkiewicz authored
* Always set ->autotune in init_hwif_sis5513(), this means practically no change in behavior since PIO was always tuned in ->ide_dma_check and >autotune was always set for ->dma_base == 0 case. * Bump driver version. Acked-by:
-
Bartlomiej Zolnierkiewicz authored
* Add sis_ata133_get_base() helper function for obtaining the address of the drive control registers on chipset_family == ATA_133 chipsets. * Add three helper functions for programming PIO/MWDMA timings: - sis_ata16_program_timings() (for ATA_16/33/66/100a chipset families) - sis_ata100_program_timings() (for ATA_100/133a chipset families) - sis_ata133_program_timings() (for ATA_133 chipset family) MWDMA timings are taken from datasheets and they match ATA spec. * Add generic helper function sis_program_timings() and use it in ->set_pio_mode and ->set_dma_mode methods (previously the driver depended on BIOS to program the correct MWDMA timings). * Remove redundant !chipset_family check from init_hwif_sis5513() (init_chipset_sis5513() guarantees that we will never get here if chipset_family cannot be determined). * SWDMA seems to be unsupported by SiS chipsets (no info about SWDMA in datasheets and for SWDMA0 mode timing requirements are impossible to fulfill) so remove ->swdma_mask from init_hwif_sis5513() and handling of SWDMA modes from sis_set_dma_mode(). * Enable DMA support for chipset_family == ATA_16. * Bump driver version. Acked-by:
-
Bartlomiej Zolnierkiewicz authored
Acked-by:
-
Kristoffer Ericson authored
This patch adds id strings for Corsair 1GB (identified as Hyperstone Model1) inside legacy/ide-cs.c. It also includes some minor whitespace cleanups. Signed-off-by:
Kristoffer Ericson <kristoffer.ericson@gmail.com> Signed-off-by:
-
Tony Battersby authored
The patch described by the following excerpt from ChangeLog-2.6.22 makes it impossible to use UDMA on a Tyan S2707 motherboard (SvrWks CSB5): commit 2d5eaa6d Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Date: Thu May 10 00:01:08 2007 +0200 ide: rework the code for selecting the best DMA transfer mode (v3) ... This one-line patch against 2.6.23 fixes the problem. Signed-off-by:
Tony Battersby <tonyb@cybernetics.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuildLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits) kbuild: introduce ccflags-y, asflags-y and ldflags-y kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP kbuild: enable use of AFLAGS and CFLAGS on commandline kbuild: enable 'make AFLAGS=...' to add additional options to AS kbuild: fix AFLAGS use in h8300 and m68knommu kbuild: check for wrong use of CFLAGS kbuild: enable 'make CFLAGS=...' to add additional options to CC kbuild: fix up CFLAGS usage kbuild: make modpost detect unterminated device id lists kbuild: call export_report from the Makefile kbuild: move Kai Germaschewski to CREDITS kconfig/menuconfig: distinguish between selected-by-another options and comments kconfig: tristate choices with mixed tristate and boolean values include/linux/Kbuild: remove duplicate entries kbuild: kill backward compatibility checks kbuild: kill EXTRA_ARFLAGS kbuild: fix documentation in makefiles.txt kbuild: call make once for all targets when O=.. is used kbuild: pass -g to assembler under CONFIG_DEBUG_INFO kbuild: update _shipped files for kconfig syntax cleanup ... Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Increase cp0 compare clockevent min_delta_ns from 0x30 to 0x300. [MIPS] Cache: Provide more information on cache policy on bootup. [MIPS] Fix aliasing bug in copy_user_highpage, take 2. [MIPS] VPE loader: convert from struct class_ device to struct device [MIPS] MIPSsim: Fix booting from NFS root [MIPS] Alchemy: Get rid of au1xxx_irq_map_t. [MIPS] Alchemy: Get rid of au_ffz(). [MIPS] Alchemy: Get rid of au_ffs(). [MIPS] Alchemy: cleanup interrupt code. [MIPS] Lasat: Fix build by conversion to irq_cpu.c. [MIPS] Lasat: Add #ifndef ... #endif include warpper to lasatint.h. [MIPS] IP22: Enable -Werror. [MIPS] IP22: Fix warning. [MIPS] IP22: Complain if requesting the front panel irq failed. [MIPS] vmlinux.lds.S: Handle KPROBES_TEXT. [MIPS] vmlinux.lds.S: Fix handling of .notes in final link. [MIPS] vmlinux.lds.S: Remove duplicate comment. [MIPS] MSP71XX: Add workarounds file. [MIPS] IP32: Fix build by conversion to irq_cpu.c.
-
Ralf Baechle authored
Extremly low values are of dubious usefulness anyway but in this case they actually were killing Qemu which simply wasn't able to complete mips_next_event() within 0x30 100MHz cycles even on fast hosts. Signed-off-by:Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
This should help making bug reports for the gadzillion of cores with all their configuration and synthesis options more useful. Signed-off-by: -
Ralf Baechle authored
Turns out b868868a wasn't quite right. When called for a page that isn't marked dirty it would artificially create an alias instead of doing the obvious thing and access the page via KSEG0. The same issue also exists in copy_to_user_page and copy_from_user_page which was causing the machine to die under rare circumstances for example when running ps if the BUG_ON() assertion added by the earlier fix was getting triggered. Signed-off-by:
-
Kay Sievers authored
Signed-off-by:
Kay Sievers <kay.sievers@vrfy.org> Signed-off-by:
-
Thiemo Seufer authored
MIPSsim probably doesn't have any sort of environment, but writing a zero in it kills even the compiled in command line. This prevents booting via NFS root. Signed-Off-By:
Thiemo Seufer <ths@networkno.de> Signed-off-by:
-
Ralf Baechle authored
Signed-off-by: -
Ralf Baechle authored
There were no users - and why have a private version anyway. Signed-off-by: -
Ralf Baechle authored
It was plain a bad idea ... Signed-off-by: -
Ralf Baechle authored
Signed-off-by: -
Ralf Baechle authored
Signed-off-by: -
Ralf Baechle authored
Signed-off-by:
-
