- 12 Dec, 2019 5 commits
-
-
Chris Wilson authored
Since dma_fence_init may call ops (because of a meaningless trace_dma_fence), we need to set the worker ops prior to that call. Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Fixes: 8e458fe2 ("drm/i915: Generalise the clflush dma-worker") Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Reviewed-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191212154224.1631531-1-chris@chris-wilson.co.uk
-
Michal Wajdeczko authored
On non-debug builds we were not using i915 param and thus we may cause "unused variable" warning/error if caller was not using i915 elsewhere. Let compiler see this param. Signed-off-by:
Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Chris Wilson authored
Execute the cmdparser asynchronously as part of the submission pipeline. Using our dma-fences, we can schedule execution after an asynchronous piece of work, so we move the cmdparser out from under the struct_mutex inside execbuf as run it as part of the submission pipeline. The same security rules apply, we copy the user batch before validation and userspace cannot touch the validation shadow. The only caveat is that we will do request construction before we complete cmdparsing and so we cannot know the outcome of the validation step until later -- so the execbuf ioctl does not report -EINVAL directly, but we must cancel execution of the request and flag the error on the out-fence. Closes: https://gitlab.freedesktop.org/drm/intel/issues/611 Closes: https://gitlab.freedesktop.org/drm/intel/issues/412Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191211230858.599030-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
The gen7 cmdparser is primarily a promotion-based system to allow access to additional registers beyond the HW validation, and allows fallback to normal execution of the user batch buffer if valid and requires chaining. In the next patch, we will do the cmdparser validation in the pipeline asynchronously and so at the point of request construction we will not know if we want to execute the privileged and validated batch, or the original user batch. The solution employed here is to execute both batches, one with raised privileges and one as normal. This is because the gen7 MI_BATCH_BUFFER_START command cannot change privilege level within a batch and must strictly use the current privilege level (or undefined behaviour kills the GPU). So in order to execute the original batch, we need a second non-priviledged batch buffer chain from the ring, i.e. we need to emit two batches for each user batch. Inside the two batches we determine which one should actually execute, we provide a conditional trampoline to call the original batch. Implementation-wise, we create a single buffer and write the shadow and the trampoline inside it at different offsets; and bind the buffer into both the kernel GGTT for the privileged execution of the shadow and into the user ppGTT for the non-privileged execution of the trampoline and original batch. One buffer, two batches and two vma. Signed-off-by:
-
Chris Wilson authored
An oversight in that we use rc6->ctl_enable to disable rc6 on gen9 and so it does not simply indicate indirect control via a PCU. Switch the rc6->ctl_enable check for a platform-based check. Fixes: 972745fd ("drm/i915/gt: Disable manual rc6 for Braswell/Baytrail") Signed-off-by:
Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191212072737.884335-2-chris@chris-wilson.co.uk
-
- 11 Dec, 2019 35 commits
-
-
Chris Wilson authored
The movntqda requires 16-byte alignment for the source pointer. Avoid falling back to clflush if the source pointer is misaligned by doing the doing a small uncached memcpy to fixup the alignments. v2: Turn the unaligned copy into a genuine helper Signed-off-by:
-
Chris Wilson authored
As the caller no longer uses the i915_vma result, stop returning it and just return the error code instead. Signed-off-by:
-
Chris Wilson authored
We need to flush the destination buffer, even on error, to maintain consistent cache state. Thereby removing the jump on error past the clear, and reducing the loop-escape mechanism to a mere break. Signed-off-by:
-
Chris Wilson authored
Declutter the calling interface by reducing the parameters to the i915_vma and associated offsets. Signed-off-by:
-
Chris Wilson authored
The cmdparser rejection debug is not for driver development, but for the user, for which we use a plain DRM_DEBUG(). Signed-off-by:
-
Chris Wilson authored
The initial investigated showed that while the PCU on Braswell/Baytrail controlled RC6 itself. setting the software RC6 request made no difference. Further testing reveals though that it causes a delay in the PCU on enabling RC6. Closes: https://gitlab.freedesktop.org/drm/intel/issues/763 Fixes: 730eaeb5 ("drm/i915/gt: Manual rc6 entry upon parking") Testcase: igt/perf/rc6-disable Signed-off-by:
-
Michal Wajdeczko authored
There is no need to pass explicit ggtt since we already have a trick to get parent gt from uc_fw, we only need to use it. Signed-off-by:
-
Michal Wajdeczko authored
There is no need to pass explicit gt since we already have a trick to get parent gt from uc_fw, we only need to use it. Signed-off-by:
-
Michal Wajdeczko authored
There is no need to pass explicit i915 since we already have a debug trick to get parent gt from uc_fw, we only need to make this trick available on non-debug builds. Signed-off-by:
-
Chris Wilson authored
Use the dev_name(i915) to identify the requests for debugging, so we can tell different device timelines apart. Signed-off-by:
Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191211150204.133471-1-chris@chris-wilson.co.uk
-
Colin Ian King authored
A prior check and return when pointer fb is null makes subsequent null checks on fb redundant. Remove the redundant null checks. Addresses-Coverity: ("Logically dead code") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191210142349.333171-1-colin.king@canonical.com
-
Colin Ian King authored
Pointer crtc_state is being assigned twice, one of these is redundant and can be removed. Addresses-Coverity: ("Evaluation order violation") Signed-off-by: -
Ville Syrjälä authored
In order to eliminate intel_pipe_to_cpu_transcoder() (and its crtc->config usage) let's pass the cpu transcoder to assert_pipe() so we don't have to do the pipe->cpu transcoder lookup on HSW+. On VLV/CHV this can get called during eDP init, which happens before crtc->config->cpu_transcoder is even populated. So currently we're always reading PIPECONF(A) there even if we're trying to check the state of some other pipe. Signed-off-by:
José Roberto de Souza <jose.souza@intel.com>
-
Ville Syrjälä authored
Let's start to eliminate intel_pipe_to_cpu_transcoder() so that we can get rid of one more crtc->config usage (which we will want to nuke as well). In the case of assert_fdi_tx() we know that we're never dealing with the EDP transcoder so we can simply replace this with a cast. v2: Fix poor English in comment Signed-off-by:
-
Chris Wilson authored
Print the i915_active state on selftest failure, with a hope it helps illuminate the cause of the failure. References: https://gitlab.freedesktop.org/drm/intel/issues/765Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191210115502.3767070-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
When we are told we have to drop all references to userptr, wait for any barriers required for unbinding. <4> [2055.808787] WARNING: CPU: 3 PID: 6239 at mm/mmu_notifier.c:472 __mmu_notifier_invalidate_range_start+0x1f2/0x250 <4> [2055.808792] Modules linked in: vgem mei_hdcp snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel r8169 lpc_ich realtek i915 snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core pinctrl_broxton snd_pcm pinctrl_intel mei_me intel_lpss_pci mei prime_numbers [last unloaded: vgem] <4> [2055.808834] CPU: 3 PID: 6239 Comm: gem_userptr_bli Tainted: G U 5.5.0-rc1-CI-CI_DRM_7522+ #1 <4> [2055.808839] Hardware name: /NUC6CAYB, BIOS AYAPLCEL.86A.0049.2018.0508.1356 05/08/2018 <4> [2055.808847] RIP: 0010:__mmu_notifier_invalidate_range_start+0x1f2/0x250 <4> [2055.808853] Code: c2 48 c7 c7 70 17 2e 82 44 89 45 d4 48 8b 70 28 e8 ec 01 ef ff 41 f6 46 20 01 44 8b 45 d4 75 0a 41 83 f8 f5 44 89 7d d4 74 89 <0f> 0b 44 89 45 d4 eb 81 0f 0b 49 8b 46 18 49 8b 76 10 4c 89 ff 48 <4> [2055.808858] RSP: 0018:ffffc90002937d40 EFLAGS: 00010202 <4> [2055.808865] RAX: 0000000000000061 RBX: ffff8882703a33e0 RCX: 0000000000000001 <4> [2055.808870] RDX: 0000000000000000 RSI: ffff888277da8cb8 RDI: 00000000ffffffff <4> [2055.808874] RBP: ffffc90002937d70 R08: 00000000fffffff5 R09: 0000000000000000 <4> [2055.808879] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001 <4> [2055.808884] R13: ffffffff822e1716 R14: ffffc90002937d80 R15: 00000000fffffff5 <4> [2055.808890] FS: 00007fda75004e40(0000) GS:ffff888277d80000(0000) knlGS:0000000000000000 <4> [2055.808895] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 <4> [2055.808900] CR2: 000055ad72ec3000 CR3: 00000002697b2000 CR4: 00000000003406e0 <4> [2055.808904] Call Trace: <4> [2055.808920] unmap_vmas+0x13e/0x150 <4> [2055.808937] unmap_region+0xa3/0x100 <4> [2055.808964] __do_munmap+0x26d/0x490 <4> [2055.808980] __vm_munmap+0x66/0xc0 <4> [2055.808994] __x64_sys_munmap+0x12/0x20 <4> [2055.809001] do_syscall_64+0x4f/0x220 Closes: https://gitlab.freedesktop.org/drm/intel/issues/771Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191210133719.3874455-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
Check that we own the global pointer before deregistering. Reported-by:
-
Tvrtko Ursulin authored
Convert i915_gem_check_execbuffer to return the error code instead of a boolean so our neat EINVAL debugging trick works within this function. Signed-off-by:
-
Chris Wilson authored
We want the bonded request to have the same scheduler properties as its master so that it is placed at the same depth in the queue. For example, consider we have requests A, B and B', where B & B' are a bonded pair to run in parallel on two engines. A -> B \- B' B will run after A and so may be scheduled on an idle engine and wait on A using a semaphore. B' sees B being executed and so enters the queue on the same engine as A. As B' did not inherit the semaphore-chain from B, it may have higher precedence than A and so preempts execution. However, B' then sits on a semaphore waiting for B, who is waiting for A, who is blocked by B. Ergo B' needs to inherit the scheduler properties from B (i.e. the semaphore chain) so that it is scheduled with the same priority as B and will not be executed ahead of Bs dependencies. Furthermore, to prevent the priorities changing via the expose fence on B', we need to couple in the dependencies for PI. This requires us to relax our sanity-checks that dependencies are strictly in order. v2: Synchronise (B, B') execution on all platforms, regardless of using a scheduler, any no-op syncs should be elided. Fixes: ee113690 ("drm/i915/execlists: Virtual engine bonding") Closes: https://gitlab.freedesktop.org/drm/intel/issues/464 Testcase: igt/gem_exec_balancer/bonded-chain Testcase: igt/gem_exec_balancer/bonded-semaphore Signed-off-by: -
Animesh Manna authored
As the current usage is restricted to first DSB instance per pipe, so existing code could not catch the issue to calculate the mmio offset of different DSB instance per pipe. Corrected the offset calculation. Fixes: a6e58d9a ("drm/i915/dsb: Check DSB engine status.") Signed-off-by:
Animesh Manna <animesh.manna@intel.com> Reviewed-by:
Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191205123513.22603-1-animesh.manna@intel.com
-
Jani Nikula authored
Sync up with v5.5-rc1 to get the updated lock_release() API among other things. Fix the conflict reported by Stephen Rothwell [1]. [1] http://lore.kernel.org/r/20191210093957.5120f717@canb.auug.org.auSigned-off-by:
-
Jani Nikula authored
Enable DSC for DSI, if specified in VBT. This still lacks DSC aware get config implementation, and therefore state checker will fail. Also mode valid is not there yet. v5: - add dsc get config call v4: - convert_rgb = true (Vandita) - ignore max cdclock check (Vandita) - rename pipe_config to crtc_state v3: - take compressed bpp into account v2: - Nuke conn_state->max_requested_bpc, it's not used on DSI Bspec: 49263 Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Vandita Kulkarni <vandita.kulkarni@intel.com> Signed-off-by:
-
Vandita Kulkarni authored
When DSC is enabled consider the compression ratio that was used during horizontal timing calculations. This may still lead to warns due to rounding errors in the round-trip. v2 by Jani: - rebase on top of the more generic dsc state readout Signed-off-by:
-
Jani Nikula authored
When DSC is enabled, we need to adjust the horizontal timings to account for the compressed (and therefore reduced) link speed. The compressed frequency ratio simplifies down to the ratio between compressed and non-compressed bpp. Bspec: 49263 Suggested-by:
-
Jani Nikula authored
When compression is enabled, configure the DSI transcoder to use compressed format. Suggested-by:
-
Jani Nikula authored
Pass crtc_state to afe_clk() to be able to take compression into account in the computation. Once we enable compression, that is. Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
We'll be expanding afe_clk() to take DSC into account. Switch to using it where DSC matters. Which is really everywhere that intel_dsi_bitrate() is currently used in ICL DSI code. The functional difference is that we round the result closest instead of down. Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
We'll make more use of it in the future. Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
The ICL DSI pipe_bpp currently comes from compute_baseline_pipe_bpp(). Fix it. Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
Add basic hardware state readout for DSC, and check the most relevant details in the state checker. v2: - check for DSC power before reading its state - check if source supports DSC at all As a side effect, this should also get the power domains for the enabled DSC on takeover, and subsequently disable DSC if it's not needed. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Jani Nikula authored
Move intel_dp_source_supports_dsc() from intel_dp.c as intel_dsc_source_support() in intel_vdsc.c. The DSC source support is more about DSC than about DP, and will be needed for DP independent code. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Reviewed-by:
-
Jani Nikula authored
Add DSI specific computation and transmission to display of PPS. With hopes that this approach will work for both DP and DSI encoders. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
Turns out this isn't compatible with DSI, where we use the value from VBT. No functional changes. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
Turns out future DSI specific parameters aren't workable with the approach of having the encoder specific functions in intel_vdsc.c. Make intel_dsc_compute_params() a helper that does the encoder independent parts, and have encoder code call it. Move intel_dsc_dp_compute_params() to intel_dp.c as intel_dp_dsc_compute_params(). No functional changes. v2: Rename pipe_config to crtc_state while at it. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
Add function for retrieving the DSC data for an encoder. Initially, this is DSI specific, as DP does not use VBT settings for DSC at all. It's also not very pretty. In the future we might have a pointer from encoder to the child device, which would make the child device list query here so much more sensible. v3: - use crtc_state instead of pipe_config - return true by default from intel_bios_get_dsc_params() - expand the comment about rc_buffer_block_size and rc_buffer_size v2: - make more robust, debug log errors better Bspec: 29885 Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
