- 29 Oct, 2019 4 commits
-
-
Vladimir Oltean authored
Background information: the driver operates the hardware in a mode where a single VLAN can be transmitted as untagged on a particular egress port. That is the "native VLAN on trunk port" use case. Its value is held in port->vid. Consider the following command sequence (no network manager, all interfaces are down, debugging prints added by me): $ ip link add dev br0 type bridge vlan_filtering 1 $ ip link set dev swp0 master br0 Kernel code path during last command: br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER): [ 21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0 br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING): [ 21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0 br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add [ 21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1 So far so good. The bridge has replaced the driver's default pvid used in standalone mode (0) with its own default_pvid (1). The port's vid (native VLAN) has also changed from 0 to 1. $ ip link set dev swp0 up [ 31.722956] 8021q: adding VLAN 0 to HW filter on device swp0 do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add: [ 31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0 The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make ports be able to transmit and receive 802.1p-tagged traffic by default. This API is supposed to offload a VLAN sub-interface, which for a switch port means to add a VLAN that is not a pvid, and tagged on egress. But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds back vid 0 as "egress untagged". Now back to the initial paragraph: there is a single untagged VID that the driver keeps track of, and that has just changed from 1 (the pvid) to 0. So this breaks the bridge core's expectation, because it has changed vid 1 from untagged to tagged, when what the user sees is. $ bridge vlan port vlan ids swp0 1 PVID Egress Untagged br0 1 PVID Egress Untagged But curiously, instead of manifesting itself as "untagged and pvid-tagged traffic gets sent as tagged on egress", the bug: - is hidden when vlan_filtering=0 - manifests as dropped traffic when vlan_filtering=1, due to this setting: if (port->vlan_aware && !port->vid) /* If port is vlan-aware and tagged, drop untagged and priority * tagged frames. */ val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA | ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA | ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA; which would have made sense if it weren't for this bug. The setting's intention was "this is a trunk port with no native VLAN, so don't accept untagged traffic". So the driver was never expecting to set VLAN 0 as the value of the native VLAN, 0 was just encoding for "invalid". So the fix is to not send 802.1p traffic as untagged, because that would change the port's native vlan to 0, unbeknownst to the bridge, and trigger unexpected code paths in the driver. Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering") Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Navid Emamdoost authored
In the implementation of i2400m_op_rfkill_sw_toggle() the allocated buffer for cmd should be released before returning. The documentation for i2400m_msg_to_dev() says when it returns the buffer can be reused. Meaning cmd should be released in either case. Move kfree(cmd) before return to be reached by all execution paths. Fixes: 2507e6ab ("wimax: i2400: fix memory leak") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
-
Jiangfeng Xiao authored
When rmmod hip04_eth.ko, we can get the following warning: Task track: rmmod(1623)>bash(1591)>login(1581)>init(1) ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac() Trying to free already-free IRQ 200 Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1 Hardware name: Hisilicon A15 [<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14) [<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8) [<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0) [<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68) [<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac) [<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c) [<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec) [<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104) [<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8) [<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c) [<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0) [<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10) ---[ end trace bb25d6123d849b44 ]--- Currently "rmmod hip04_eth.ko" call free_irq more than once as devres_release_all and hip04_remove both call free_irq. This results in a 'Trying to free already-free IRQ' warning. To solve the problem free_irq has been moved out of hip04_remove. Signed-off-by:
Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by:
-
Will Deacon authored
In the highly unlikely event that we fail to allocate either of the "/txrx" or "/control" workqueues, we should bail cleanly rather than blindly march on with NULL queue pointer(s) installed in the 'fjes_adapter' instance. Cc: "David S. Miller" <davem@davemloft.net> Reported-by:
Nicolas Waisman <nico@semmle.com> Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
-
- 28 Oct, 2019 13 commits
-
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Simon Wunderlich says: ==================== Here are two batman-adv bugfixes: * Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches) ==================== Signed-off-by: -
Daniel Wagner authored
lan78xx_status() will run with interrupts enabled due to the change in ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler"). generic_handle_irq() expects to be run with IRQs disabled. [ 4.886203] 000: irq 79 handler irq_default_primary_handler+0x0/0x8 enabled interrupts [ 4.886243] 000: WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:152 __handle_irq_event_percpu+0x154/0x168 [ 4.896294] 000: Modules linked in: [ 4.896301] 000: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.6 #39 [ 4.896310] 000: Hardware name: Raspberry Pi 3 Model B+ (DT) [ 4.896315] 000: pstate: 60000005 (nZCv daif -PAN -UAO) [ 4.896321] 000: pc : __handle_irq_event_percpu+0x154/0x168 [ 4.896331] 000: lr : __handle_irq_event_percpu+0x154/0x168 [ 4.896339] 000: sp : ffff000010003cc0 [ 4.896346] 000: x29: ffff000010003cc0 x28: 0000000000000060 [ 4.896355] 000: x27: ffff000011021980 x26: ffff00001189c72b [ 4.896364] 000: x25: ffff000011702bc0 x24: ffff800036d6e400 [ 4.896373] 000: x23: 000000000000004f x22: ffff000010003d64 [ 4.896381] 000: x21: 0000000000000000 x20: 0000000000000002 [ 4.896390] 000: x19: ffff8000371c8480 x18: 0000000000000060 [ 4.896398] 000: x17: 0000000000000000 x16: 00000000000000eb [ 4.896406] 000: x15: ffff000011712d18 x14: 7265746e69206465 [ 4.896414] 000: x13: ffff000010003ba0 x12: ffff000011712df0 [ 4.896422] 000: x11: 0000000000000001 x10: ffff000011712e08 [ 4.896430] 000: x9 : 0000000000000001 x8 : 000000000003c920 [ 4.896437] 000: x7 : ffff0000118cc410 x6 : ffff0000118c7f00 [ 4.896445] 000: x5 : 000000000003c920 x4 : 0000000000004510 [ 4.896453] 000: x3 : ffff000011712dc8 x2 : 0000000000000000 [ 4.896461] 000: x1 : 73a3f67df94c1500 x0 : 0000000000000000 [ 4.896466] 000: Call trace: [ 4.896471] 000: __handle_irq_event_percpu+0x154/0x168 [ 4.896481] 000: handle_irq_event_percpu+0x50/0xb0 [ 4.896489] 000: handle_irq_event+0x40/0x98 [ 4.896497] 000: handle_simple_irq+0xa4/0xf0 [ 4.896505] 000: generic_handle_irq+0x24/0x38 [ 4.896513] 000: intr_complete+0xb0/0xe0 [ 4.896525] 000: __usb_hcd_giveback_urb+0x58/0xd8 [ 4.896533] 000: usb_giveback_urb_bh+0xd0/0x170 [ 4.896539] 000: tasklet_action_common.isra.0+0x9c/0x128 [ 4.896549] 000: tasklet_hi_action+0x24/0x30 [ 4.896556] 000: __do_softirq+0x120/0x23c [ 4.896564] 000: irq_exit+0xb8/0xd8 [ 4.896571] 000: __handle_domain_irq+0x64/0xb8 [ 4.896579] 000: bcm2836_arm_irqchip_handle_irq+0x60/0xc0 [ 4.896586] 000: el1_irq+0xb8/0x140 [ 4.896592] 000: arch_cpu_idle+0x10/0x18 [ 4.896601] 000: do_idle+0x200/0x280 [ 4.896608] 000: cpu_startup_entry+0x20/0x28 [ 4.896615] 000: rest_init+0xb4/0xc0 [ 4.896623] 000: arch_call_rest_init+0xc/0x14 [ 4.896632] 000: start_kernel+0x454/0x480 Fixes: ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler") Cc: Woojung Huh <woojung.huh@microchip.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Stefan Wahren <wahrenst@gmx.net> Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: David Miller <davem@davemloft.net> Signed-off-by:
Daniel Wagner <dwagner@suse.de> Tested-by:
Stefan Wahren <wahrenst@gmx.net> Signed-off-by:
-
Arnd Bergmann authored
An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO, but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y, which still causes a link error: drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio': sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free' sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get' drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown': sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free' Change the dependency to only allow selecting the TAS code when it can link against the taprio code. Fixes: a8d570de ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS") Fixes: 317ab5b8 ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Benjamin Herrenschmidt authored
We are calling the checksum helper after the dma_map_single() call to map the packet. This is incorrect as the checksumming code will touch the packet from the CPU. This means the cache won't be properly flushes (or the bounce buffering will leave us with the unmodified packet to DMA). This moves the calculation of the checksum & vlan tags to before the DMA mapping. This also has the side effect of fixing another bug: If the checksum helper fails, we goto "drop" to drop the packet, which will not unmap the DMA mapping. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Fixes: 05690d63 ("ftgmac100: Upgrade to NETIF_F_HW_CSUM") Reviewed-by:
Vijay Khemka <vijaykhemka@fb.com> Tested-by:
-
Tejun Heo authored
sk_page_frag() optimizes skb_frag allocations by using per-task skb_frag cache when it knows it's the only user. The condition is determined by seeing whether the socket allocation mask allows blocking - if the allocation may block, it obviously owns the task's context and ergo exclusively owns current->task_frag. Unfortunately, this misses recursion through memory reclaim path. Please take a look at the following backtrace. [2] RIP: 0010:tcp_sendmsg_locked+0xccf/0xe10 ... tcp_sendmsg+0x27/0x40 sock_sendmsg+0x30/0x40 sock_xmit.isra.24+0xa1/0x170 [nbd] nbd_send_cmd+0x1d2/0x690 [nbd] nbd_queue_rq+0x1b5/0x3b0 [nbd] __blk_mq_try_issue_directly+0x108/0x1b0 blk_mq_request_issue_directly+0xbd/0xe0 blk_mq_try_issue_list_directly+0x41/0xb0 blk_mq_sched_insert_requests+0xa2/0xe0 blk_mq_flush_plug_list+0x205/0x2a0 blk_flush_plug_list+0xc3/0xf0 [1] blk_finish_plug+0x21/0x2e _xfs_buf_ioapply+0x313/0x460 __xfs_buf_submit+0x67/0x220 xfs_buf_read_map+0x113/0x1a0 xfs_trans_read_buf_map+0xbf/0x330 xfs_btree_read_buf_block.constprop.42+0x95/0xd0 xfs_btree_lookup_get_block+0x95/0x170 xfs_btree_lookup+0xcc/0x470 xfs_bmap_del_extent_real+0x254/0x9a0 __xfs_bunmapi+0x45c/0xab0 xfs_bunmapi+0x15/0x30 xfs_itruncate_extents_flags+0xca/0x250 xfs_free_eofblocks+0x181/0x1e0 xfs_fs_destroy_inode+0xa8/0x1b0 destroy_inode+0x38/0x70 dispose_list+0x35/0x50 prune_icache_sb+0x52/0x70 super_cache_scan+0x120/0x1a0 do_shrink_slab+0x120/0x290 shrink_slab+0x216/0x2b0 shrink_node+0x1b6/0x4a0 do_try_to_free_pages+0xc6/0x370 try_to_free_mem_cgroup_pages+0xe3/0x1e0 try_charge+0x29e/0x790 mem_cgroup_charge_skmem+0x6a/0x100 __sk_mem_raise_allocated+0x18e/0x390 __sk_mem_schedule+0x2a/0x40 [0] tcp_sendmsg_locked+0x8eb/0xe10 tcp_sendmsg+0x27/0x40 sock_sendmsg+0x30/0x40 ___sys_sendmsg+0x26d/0x2b0 __sys_sendmsg+0x57/0xa0 do_syscall_64+0x42/0x100 entry_SYSCALL_64_after_hwframe+0x44/0xa9 In [0], tcp_send_msg_locked() was using current->page_frag when it called sk_wmem_schedule(). It already calculated how many bytes can be fit into current->page_frag. Due to memory pressure, sk_wmem_schedule() called into memory reclaim path which called into xfs and then IO issue path. Because the filesystem in question is backed by nbd, the control goes back into the tcp layer - back into tcp_sendmsg_locked(). nbd sets sk_allocation to (GFP_NOIO | __GFP_MEMALLOC) which makes sense - it's in the process of freeing memory and wants to be able to, e.g., drop clean pages to make forward progress. However, this confused sk_page_frag() called from [2]. Because it only tests whether the allocation allows blocking which it does, it now thinks current->page_frag can be used again although it already was being used in [0]. After [2] used current->page_frag, the offset would be increased by the used amount. When the control returns to [0], current->page_frag's offset is increased and the previously calculated number of bytes now may overrun the end of allocated memory leading to silent memory corruptions. Fix it by adding gfpflags_normal_context() which tests sleepable && !reclaim and use it to determine whether to use current->task_frag. v2: Eric didn't like gfp flags being tested twice. Introduce a new helper gfpflags_normal_context() and combine the two tests. Signed-off-by:Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Eric Dumazet authored
KCSAN reported a data-race in udp_set_dev_scratch() [1] The issue here is that we must not write over skb fields if skb is shared. A similar issue has been fixed in commit 89c22d8c ("net: Fix skb csum races when peeking") While we are at it, use a helper only dealing with udp_skb_scratch(skb)->csum_unnecessary, as this allows udp_set_dev_scratch() to be called once and thus inlined. [1] BUG: KCSAN: data-race in udp_set_dev_scratch / udpv6_recvmsg write to 0xffff888120278317 of 1 bytes by task 10411 on cpu 1: udp_set_dev_scratch+0xea/0x200 net/ipv4/udp.c:1308 __first_packet_length+0x147/0x420 net/ipv4/udp.c:1556 first_packet_length+0x68/0x2a0 net/ipv4/udp.c:1579 udp_poll+0xea/0x110 net/ipv4/udp.c:2720 sock_poll+0xed/0x250 net/socket.c:1256 vfs_poll include/linux/poll.h:90 [inline] do_select+0x7d0/0x1020 fs/select.c:534 core_sys_select+0x381/0x550 fs/select.c:677 do_pselect.constprop.0+0x11d/0x160 fs/select.c:759 __do_sys_pselect6 fs/select.c:784 [inline] __se_sys_pselect6 fs/select.c:769 [inline] __x64_sys_pselect6+0x12e/0x170 fs/select.c:769 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 read to 0xffff888120278317 of 1 bytes by task 10413 on cpu 0: udp_skb_csum_unnecessary include/net/udp.h:358 [inline] udpv6_recvmsg+0x43e/0xe90 net/ipv6/udp.c:310 inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592 sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871 ___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480 do_recvmmsg+0x19a/0x5c0 net/socket.c:2601 __sys_recvmmsg+0x1ef/0x200 net/socket.c:2680 __do_sys_recvmmsg net/socket.c:2703 [inline] __se_sys_recvmmsg net/socket.c:2696 [inline] __x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 10413 Comm: syz-executor.0 Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 2276f58a ("udp: use a separate rx queue for packet reception") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header files related to DPAA2 Ethernet driver supporting Freescale SoCs with DPAA2. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net: avoid KCSAN splats Often times we use skb_queue_empty() without holding a lock, meaning that other cpus (or interrupt) can change the queue under us. This is fine, but we need to properly annotate the lockless intent to make sure the compiler wont over optimize things. ==================== Signed-off-by: -
Eric Dumazet authored
__skb_wait_for_more_packets() can be called while other cpus can feed packets to the socket receive queue. KCSAN reported : BUG: KCSAN: data-race in __skb_wait_for_more_packets / __udp_enqueue_schedule_skb write to 0xffff888102e40b58 of 8 bytes by interrupt on cpu 0: __skb_insert include/linux/skbuff.h:1852 [inline] __skb_queue_before include/linux/skbuff.h:1958 [inline] __skb_queue_tail include/linux/skbuff.h:1991 [inline] __udp_enqueue_schedule_skb+0x2d7/0x410 net/ipv4/udp.c:1470 __udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline] udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057 udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074 udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233 __udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300 udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252 dst_input include/net/dst.h:442 [inline] ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5124 process_backlog+0x1d3/0x420 net/core/dev.c:5955 read to 0xffff888102e40b58 of 8 bytes by task 13035 on cpu 1: __skb_wait_for_more_packets+0xfa/0x320 net/core/datagram.c:100 __skb_recv_udp+0x374/0x500 net/ipv4/udp.c:1683 udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712 inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838 sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871 ___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480 do_recvmmsg+0x19a/0x5c0 net/socket.c:2601 __sys_recvmmsg+0x1ef/0x200 net/socket.c:2680 __do_sys_recvmmsg net/socket.c:2703 [inline] __se_sys_recvmmsg net/socket.c:2696 [inline] __x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 13035 Comm: syz-executor.3 Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by:
-
Eric Dumazet authored
Busy polling usually runs without locks. Let's use skb_queue_empty_lockless() instead of skb_queue_empty() Also uses READ_ONCE() in __skb_try_recv_datagram() to address a similar potential problem. Signed-off-by:
-
Eric Dumazet authored
Many poll() handlers are lockless. Using skb_queue_empty_lockless() instead of skb_queue_empty() is more appropriate. Signed-off-by:
-
Eric Dumazet authored
syzbot reported a data-race [1]. We should use skb_queue_empty_lockless() to document that we are not ensuring a mutual exclusion and silence KCSAN. [1] BUG: KCSAN: data-race in __skb_recv_udp / __udp_enqueue_schedule_skb write to 0xffff888122474b50 of 8 bytes by interrupt on cpu 0: __skb_insert include/linux/skbuff.h:1852 [inline] __skb_queue_before include/linux/skbuff.h:1958 [inline] __skb_queue_tail include/linux/skbuff.h:1991 [inline] __udp_enqueue_schedule_skb+0x2c1/0x410 net/ipv4/udp.c:1470 __udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline] udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057 udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074 udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233 __udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300 udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470 ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204 ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252 dst_input include/net/dst.h:442 [inline] ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413 NF_HOOK include/linux/netfilter.h:305 [inline] NF_HOOK include/linux/netfilter.h:299 [inline] ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523 __netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010 __netif_receive_skb+0x37/0xf0 net/core/dev.c:5124 process_backlog+0x1d3/0x420 net/core/dev.c:5955 read to 0xffff888122474b50 of 8 bytes by task 8921 on cpu 1: skb_queue_empty include/linux/skbuff.h:1494 [inline] __skb_recv_udp+0x18d/0x500 net/ipv4/udp.c:1653 udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712 inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838 sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871 ___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480 do_recvmmsg+0x19a/0x5c0 net/socket.c:2601 __sys_recvmmsg+0x1ef/0x200 net/socket.c:2680 __do_sys_recvmmsg net/socket.c:2703 [inline] __se_sys_recvmmsg net/socket.c:2696 [inline] __x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 8921 Comm: syz-executor.4 Not tainted 5.4.0-rc3+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by:
-
Eric Dumazet authored
Some paths call skb_queue_empty() without holding the queue lock. We must use a barrier in order to not let the compiler do strange things, and avoid KCSAN splats. Adding a barrier in skb_queue_empty() might be overkill, I prefer adding a new helper to clearly identify points where the callers might be lockless. This might help us finding real bugs. The corresponding WRITE_ONCE() should add zero cost for current compilers. Signed-off-by:
-
- 27 Oct, 2019 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter/IPVS fixes for net The following patchset contains Netfilter/IPVS fixes for net: 1) Fix crash on flowtable due to race between garbage collection and insertion. 2) Restore callback unbinding in netfilter offloads. 3) Fix races on IPVS module removal, from Davide Caratti. 4) Make old_secure_tcp per-netns to fix sysbot report, from Eric Dumazet. 5) Validate matching length in netfilter offloads, from wenxu. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf 2019-10-27 The following pull-request contains BPF updates for your *net* tree. We've added 7 non-merge commits during the last 11 day(s) which contain a total of 7 files changed, 66 insertions(+), 16 deletions(-). The main changes are: 1) Fix two use-after-free bugs in relation to RCU in jited symbol exposure to kallsyms, from Daniel Borkmann. 2) Fix NULL pointer dereference in AF_XDP rx-only sockets, from Magnus Karlsson. 3) Fix hang in netdev unregister for hash based devmap as well as another overflow bug on 32 bit archs in memlock cost calculation, from Toke Høiland-Jørgensen. 4) Fix wrong memory access in LWT BPF programs on reroute due to invalid dst. Also fix BPF selftests to use more compatible nc options, from Jiri Benc. ==================== Signed-off-by:
-
- 26 Oct, 2019 11 commits
-
-
David S. Miller authored
Paolo Abeni says: ==================== ipv4: fix route update on metric change. This fixes connected route update on some edge cases for ip addr metric change. It additionally includes self tests for the covered scenarios. The new tests fail on unpatched kernels and pass on the patched one. v1 -> v2: - add selftests ==================== Signed-off-by: -
Paolo Abeni authored
This patch adds two more tests to ipv4_addr_metric_test() to explicitly cover the scenarios fixed by the previous patch. Suggested-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Paolo Abeni authored
Since commit af4d768a ("net/ipv4: Add support for specifying metric of connected routes"), when updating an IP address with a different metric, the associated connected route is updated, too. Still, the mentioned commit doesn't handle properly some corner cases: $ ip addr add dev eth0 192.168.1.0/24 $ ip addr add dev eth0 192.168.2.1/32 peer 192.168.2.2 $ ip addr add dev eth0 192.168.3.1/24 $ ip addr change dev eth0 192.168.1.0/24 metric 10 $ ip addr change dev eth0 192.168.2.1/32 peer 192.168.2.2 metric 10 $ ip addr change dev eth0 192.168.3.1/24 metric 10 $ ip -4 route 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.0 192.168.2.2 dev eth0 proto kernel scope link src 192.168.2.1 192.168.3.0/24 dev eth0 proto kernel scope link src 192.168.2.1 metric 10 Only the last route is correctly updated. The problem is the current test in fib_modify_prefix_metric(): if (!(dev->flags & IFF_UP) || ifa->ifa_flags & (IFA_F_SECONDARY | IFA_F_NOPREFIXROUTE) || ipv4_is_zeronet(prefix) || prefix == ifa->ifa_local || ifa->ifa_prefixlen == 32) Which should be the logical 'not' of the pre-existing test in fib_add_ifaddr(): if (!ipv4_is_zeronet(prefix) && !(ifa->ifa_flags & IFA_F_SECONDARY) && (prefix != addr || ifa->ifa_prefixlen < 32)) To properly negate the original expression, we need to change the last logical 'or' to a logical 'and'. Fixes: af4d768a ("net/ipv4: Add support for specifying metric of connected routes") Reported-and-suggested-by:
Beniamino Galvani <bgalvani@redhat.com> Signed-off-by:
-
zhanglin authored
memset() the structure ethtool_wolinfo that has padded bytes but the padded bytes have not been zeroed out. Signed-off-by:
zhanglin <zhang.lin16@zte.com.cn> Signed-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvsPablo Neira Ayuso authored
Simon Horman says: ==================== IPVS fixes for v5.4 * Eric Dumazet resolves a race condition in switching the defense level * Davide Caratti resolves a race condition in module removal ==================== Signed-off-by:Pablo Neira Ayuso <pablo@netfilter.org>
-
Raju Rangoju authored
For adapters which support the SGE Doorbell Queue Timer facility, we configured the Ethernet TX Queues to send CIDX Updates to the Associated Ethernet RX Response Queue with CPL_SGE_EGR_UPDATE messages to allow us to respond more quickly to the CIDX Updates. But, this was adding load to PCIe Link RX bandwidth and, potentially, resulting in higher CPU Interrupt load. This patch requests the HW to deliver the CIDX updates to the TX queue status page rather than generating an ingress queue message (as an interrupt). With this patch, the load on RX bandwidth is reduced and a substantial improvement in BW is noticed at lower IO sizes. Fixes: d429005f ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer") Signed-off-by:
Raju Rangoju <rajur@chelsio.com> Signed-off-by:
-
Guillaume Nault authored
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances, but there are a few paths calling rtnl_net_notifyid() from atomic context or from RCU critical sections. The later also precludes the use of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new() call is wrong too, as it uses GFP_KERNEL unconditionally. Therefore, we need to pass the GFP flags as parameter and propagate it through function calls until the proper flags can be determined. In most cases, GFP_KERNEL is fine. The exceptions are: * openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump() indirectly call rtnl_net_notifyid() from RCU critical section, * rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as parameter. Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used by nlmsg_new(). The function is allowed to sleep, so better make the flags consistent with the ones used in the following ovs_vport_cmd_fill_info() call. Found by code inspection. Fixes: 9a963454 ("netns: notify netns id events") Signed-off-by:Guillaume Nault <gnault@redhat.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header file related to ethernet driver for Cortina Gemini devices. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: fixes for -net Fixes for the net tree, covering a memleak when closing SMC fallback sockets and fix SMC-R connection establishment when vlan-ids are used. ==================== Signed-off-by: -
Ursula Braun authored
Creating of an SMC-R connection with vlan-id fails, because smc_listen_work() determines the vlan_id of the connection, saves it in struct smc_init_info ini, but clears the ini area again if SMC-D is not applicable. This patch just resets the ISM device before investigating SMC-R availability. Fixes: bc36d2fc ("net/smc: consolidate function parameters") Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Ursula Braun authored
For SMC sockets forced to fallback to TCP, the file is propagated from the outer SMC to the internal TCP socket. When closing the SMC socket, the internal TCP socket file pointer must be restored to the original NULL value, otherwise memory leaks may show up (found with CONFIG_DEBUG_KMEMLEAK). The internal TCP socket is released in smc_clcsock_release(), which calls __sock_release() function in net/socket.c. This calls the needed iput(SOCK_INODE(sock)) only, if the file pointer has been reset to the original NULL-value. Fixes: 07603b23 ("net/smc: propagate file from SMC to TCP socket") Signed-off-by:
-
- 25 Oct, 2019 3 commits
-
-
Ben Dooks (Codethink) authored
If CONFIG_NET_HWBM is not set, then these stub functions in <net/hwbm.h> should be declared static to avoid trying to export them from any driver that includes this. Fixes the following sparse warnings: ./include/net/hwbm.h:24:6: warning: symbol 'hwbm_buf_free' was not declared. Should it be static? ./include/net/hwbm.h:25:5: warning: symbol 'hwbm_pool_refill' was not declared. Should it be static? ./include/net/hwbm.h:26:5: warning: symbol 'hwbm_pool_add' was not declared. Should it be static? Signed-off-by:
Ben Dooks (Codethink) <ben.dooks@codethink.co.uk> Signed-off-by:
-
Ben Dooks (Codethink) authored
If the CONFIG_MVNET_BA is not set, then make the stub functions static inline to avoid trying to export them, and remove hte following sparse warnings: drivers/net/ethernet/marvell/mvneta_bm.h:163:6: warning: symbol 'mvneta_bm_pool_destroy' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:165:6: warning: symbol 'mvneta_bm_bufs_free' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:167:5: warning: symbol 'mvneta_bm_construct' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:168:5: warning: symbol 'mvneta_bm_pool_refill' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:170:23: warning: symbol 'mvneta_bm_pool_use' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:181:18: warning: symbol 'mvneta_bm_get' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:182:6: warning: symbol 'mvneta_bm_put' was not declared. Should it be static? Signed-off-by:
-
Vincent Prince authored
There is networking hardware that isn't based on Ethernet for layers 1 and 2. For example CAN. CAN is a multi-master serial bus standard for connecting Electronic Control Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes of payload. Frame corruption is detected by a CRC. However frame loss due to corruption is possible, but a quite unusual phenomenon. While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of legacy protocols on top of CAN, which are not build with flow control or high CAN frame drop rates in mind. When using fq_codel, as soon as the queue reaches a certain delay based length, skbs from the head of the queue are silently dropped. Silently meaning that the user space using a send() or similar syscall doesn't get an error. However TCP's flow control algorithm will detect dropped packages and adjust the bandwidth accordingly. When using fq_codel and sending raw frames over CAN, which is the common use case, the user space thinks the package has been sent without problems, because send() returned without an error. pfifo_fast will drop skbs, if the queue length exceeds the maximum. But with this scheduler the skbs at the tail are dropped, an error (-ENOBUFS) is propagated to user space. So that the user space can slow down the package generation. On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH during compile time, or set default during runtime with sysctl net.core.default_qdisc (see [1]), we get a bad user experience. In my test case with pfifo_fast, I can transfer thousands of million CAN frames without a frame drop. On the other hand with fq_codel there is more then one lost CAN frame per thousand frames. As pointed out fq_codel is not suited for CAN hardware, so this patch changes attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices. During transition of a netdev from down to up state the default queuing discipline is attached by attach_default_qdiscs() with the help of attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to attach the pfifo_fast (pfifo_fast_ops) if the network device type is "ARPHRD_CAN". [1] https://github.com/systemd/systemd/issues/9194Signed-off-by:
Vincent Prince <vincent.prince.fr@gmail.com> Signed-off-by:
-
- 24 Oct, 2019 7 commits
-
-
David S. Miller authored
Taehee Yoo says: ==================== net: fix nested device bugs This patchset fixes several bugs that are related to nesting device infrastructure. Current nesting infrastructure code doesn't limit the depth level of devices. nested devices could be handled recursively. at that moment, it needs huge memory and stack overflow could occur. Below devices type have same bug. VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, and VXLAN. But I couldn't test all interface types so there could be more device types, which have similar problems. Maybe qmi_wwan.c code could have same problem. So, I would appreciate if someone test qmi_wwan.c and other modules. Test commands: ip link add dummy0 type dummy ip link add vlan1 link dummy0 type vlan id 1 for i in {2..100} do let A=$i-1 ip link add name vlan$i link vlan$A type vlan id $i done ip link del dummy0 1st patch actually fixes the root cause. It adds new common variables {upper/lower}_level that represent depth level. upper_level variable is depth of upper devices. lower_level variable is depth of lower devices. [U][L] [U][L] vlan1 1 5 vlan4 1 4 vlan2 2 4 vlan5 2 3 vlan3 3 3 | | | +------------+ | vlan6 4 2 dummy0 5 1 After this patch, the nesting infrastructure code uses this variable to check the depth level. 2nd patch fixes Qdisc lockdep related problem. Before this patch, devices use static lockdep map. So, if devices that are same types are nested, lockdep will warn about recursive situation. These patches make these devices use dynamic lockdep key instead of static lock or subclass. 3rd patch fixes unexpected IFF_BONDING bit unset. When nested bonding interface scenario, bonding interface could lost it's IFF_BONDING flag. This should not happen. This patch adds a condition before unsetting IFF_BONDING. 4th patch fixes nested locking problem in bonding interface Bonding interface has own lock and this uses static lock. Bonding interface could be nested and it uses same lockdep key. So that unexisting lockdep warning occurs. 5th patch fixes nested locking problem in team interface Team interface has own lock and this uses static lock. Team interface could be nested and it uses same lockdep key. So that unexisting lockdep warning occurs. 6th patch fixes a refcnt leak in the macsec module. When the macsec module is unloaded, refcnt leaks occur. But actually, that holding refcnt is unnecessary. So this patch just removes these code. 7th patch adds ignore flag to an adjacent structure. In order to exchange an adjacent node safely, ignore flag is needed. 8th patch makes vxlan add an adjacent link to limit depth level. Vxlan interface could set it's lower interface and these lower interfaces are handled recursively. So, if the depth of lower interfaces is too deep, stack overflow could happen. 9th patch removes unnecessary variables and callback. After 1st patch, subclass callback and variables are unnecessary. This patch just removes these variables and callback. 10th patch fix refcnt leaks in the virt_wifi module Like every nested interface, the upper interface should be deleted before the lower interface is deleted. In order to fix this, the notifier routine is added in this patch. v4 -> v5 : - Update log messages - Move variables position, 1st patch - Fix iterator routine, 1st patch - Add generic lockdep key code, which replaces 2, 4, 5, 6, 7 patches. - Log message update, 10th patch - Fix wrong error value in error path of __init routine, 10th patch - hold module refcnt when interface is created, 10th patch v3 -> v4 : - Add new 12th patch to fix refcnt leaks in the virt_wifi module - Fix wrong usage netdev_upper_dev_link() in the vxlan.c - Preserve reverse christmas tree variable ordering in the vxlan.c - Add missing static keyword in the dev.c - Expose netdev_adjacent_change_{prepare/commit/abort} instead of netdev_adjacent_dev_{enable/disable} v2 -> v3 : - Modify nesting infrastructure code to use iterator instead of recursive. v1 -> v2 : - Make the 3rd patch do not add a new priv_flag. ==================== Signed-off-by: -
Taehee Yoo authored
virt_wifi_newlink() calls netdev_upper_dev_link() and it internally holds reference count of lower interface. Current code does not release a reference count of the lower interface when the lower interface is being deleted. So, reference count leaks occur. Test commands: ip link add dummy0 type dummy ip link add vw1 link dummy0 type virt_wifi ip link del dummy0 Splat looks like: [ 133.787526][ T788] WARNING: CPU: 1 PID: 788 at net/core/dev.c:8274 rollback_registered_many+0x835/0xc80 [ 133.788355][ T788] Modules linked in: virt_wifi cfg80211 dummy team af_packet sch_fq_codel ip_tables x_tables unix [ 133.789377][ T788] CPU: 1 PID: 788 Comm: ip Not tainted 5.4.0-rc3+ #96 [ 133.790069][ T788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 133.791167][ T788] RIP: 0010:rollback_registered_many+0x835/0xc80 [ 133.791906][ T788] Code: 00 4d 85 ff 0f 84 b5 fd ff ff ba c0 0c 00 00 48 89 de 4c 89 ff e8 9b 58 04 00 48 89 df e8 30 [ 133.794317][ T788] RSP: 0018:ffff88805ba3f338 EFLAGS: 00010202 [ 133.795080][ T788] RAX: ffff88805e57e801 RBX: ffff88805ba34000 RCX: ffffffffa9294723 [ 133.796045][ T788] RDX: 1ffff1100b746816 RSI: 0000000000000008 RDI: ffffffffabcc4240 [ 133.797006][ T788] RBP: ffff88805ba3f4c0 R08: fffffbfff5798849 R09: fffffbfff5798849 [ 133.797993][ T788] R10: 0000000000000001 R11: fffffbfff5798848 R12: dffffc0000000000 [ 133.802514][ T788] R13: ffff88805ba3f440 R14: ffff88805ba3f400 R15: ffff88805ed622c0 [ 133.803237][ T788] FS: 00007f2e9608c0c0(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000 [ 133.804002][ T788] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 133.804664][ T788] CR2: 00007f2e95610603 CR3: 000000005f68c004 CR4: 00000000000606e0 [ 133.805363][ T788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 133.806073][ T788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 133.806787][ T788] Call Trace: [ 133.807069][ T788] ? generic_xdp_install+0x310/0x310 [ 133.807612][ T788] ? lock_acquire+0x164/0x3b0 [ 133.808077][ T788] ? is_bpf_text_address+0x5/0xf0 [ 133.808640][ T788] ? deref_stack_reg+0x9c/0xd0 [ 133.809138][ T788] ? __nla_validate_parse+0x98/0x1ab0 [ 133.809944][ T788] unregister_netdevice_many.part.122+0x13/0x1b0 [ 133.810599][ T788] rtnl_delete_link+0xbc/0x100 [ 133.811073][ T788] ? rtnl_af_register+0xc0/0xc0 [ 133.811672][ T788] rtnl_dellink+0x30e/0x8a0 [ 133.812205][ T788] ? is_bpf_text_address+0x5/0xf0 [ ... ] [ 144.110530][ T788] unregister_netdevice: waiting for dummy0 to become free. Usage count = 1 This patch adds notifier routine to delete upper interface before deleting lower interface. Fixes: c7cdba31 ("mac80211-next: rtnetlink wifi simulation device") Signed-off-by:Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Taehee Yoo authored
This patch removes variables and callback these are related to the nested device structure. devices that can be nested have their own nest_level variable that represents the depth of nested devices. In the previous patch, new {lower/upper}_level variables are added and they replace old private nest_level variable. So, this patch removes all 'nest_level' variables. In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added to get lockdep subclass value, which is actually lower nested depth value. But now, they use the dynamic lockdep key to avoid lockdep warning instead of the subclass. So, this patch removes ->ndo_get_lock_subclass() callback. Signed-off-by: -
Taehee Yoo authored
Current vxlan code doesn't limit the number of nested devices. Nested devices would be handled recursively and this routine needs huge stack memory. So, unlimited nested devices could make stack overflow. In order to fix this issue, this patch adds adjacent links. The adjacent link APIs internally check the depth level. Test commands: ip link add dummy0 type dummy ip link add vxlan0 type vxlan id 0 group 239.1.1.1 dev dummy0 \ dstport 4789 for i in {1..100} do let A=$i-1 ip link add vxlan$i type vxlan id $i group 239.1.1.1 \ dev vxlan$A dstport 4789 done ip link del dummy0 The top upper link is vxlan100 and the lowest link is vxlan0. When vxlan0 is deleting, the upper devices will be deleted recursively. It needs huge stack memory so it makes stack overflow. Splat looks like: [ 229.628477] ============================================================================= [ 229.629785] BUG page->ptl (Not tainted): Padding overwritten. 0x0000000026abf214-0x0000000091f6abb2 [ 229.629785] ----------------------------------------------------------------------------- [ 229.629785] [ 229.655439] ================================================================== [ 229.629785] INFO: Slab 0x00000000ff7cfda8 objects=19 used=19 fp=0x00000000fe33776c flags=0x200000000010200 [ 229.655688] BUG: KASAN: stack-out-of-bounds in unmap_single_vma+0x25a/0x2e0 [ 229.655688] Read of size 8 at addr ffff888113076928 by task vlan-network-in/2334 [ 229.655688] [ 229.629785] Padding 0000000026abf214: 00 80 14 0d 81 88 ff ff 68 91 81 14 81 88 ff ff ........h....... [ 229.629785] Padding 0000000001e24790: 38 91 81 14 81 88 ff ff 68 91 81 14 81 88 ff ff 8.......h....... [ 229.629785] Padding 00000000b39397c8: 33 30 62 a7 ff ff ff ff ff eb 60 22 10 f1 ff 1f 30b.......`".... [ 229.629785] Padding 00000000bc98f53a: 80 60 07 13 81 88 ff ff 00 80 14 0d 81 88 ff ff .`.............. [ 229.629785] Padding 000000002aa8123d: 68 91 81 14 81 88 ff ff f7 21 17 a7 ff ff ff ff h........!...... [ 229.629785] Padding 000000001c8c2369: 08 81 14 0d 81 88 ff ff 03 02 00 00 00 00 00 00 ................ [ 229.629785] Padding 000000004e290c5d: 21 90 a2 21 10 ed ff ff 00 00 00 00 00 fc ff df !..!............ [ 229.629785] Padding 000000000e25d731: 18 60 07 13 81 88 ff ff c0 8b 13 05 81 88 ff ff .`.............. [ 229.629785] Padding 000000007adc7ab3: b3 8a b5 41 00 00 00 00 ...A.... [ 229.629785] FIX page->ptl: Restoring 0x0000000026abf214-0x0000000091f6abb2=0x5a [ ... ] Fixes: acaf4e70 ("net: vxlan: when lower dev unregisters remove vxlan dev as well") Signed-off-by: -
Taehee Yoo authored
In order to link an adjacent node, netdev_upper_dev_link() is used and in order to unlink an adjacent node, netdev_upper_dev_unlink() is used. unlink operation does not fail, but link operation can fail. In order to exchange adjacent nodes, we should unlink an old adjacent node first. then, link a new adjacent node. If link operation is failed, we should link an old adjacent node again. But this link operation can fail too. It eventually breaks the adjacent link relationship. This patch adds an ignore flag into the netdev_adjacent structure. If this flag is set, netdev_upper_dev_link() ignores an old adjacent node for a moment. This patch also adds new functions for other modules. netdev_adjacent_change_prepare() netdev_adjacent_change_commit() netdev_adjacent_change_abort() netdev_adjacent_change_prepare() inserts new device into adjacent list but new device is not allowed to use immediately. If netdev_adjacent_change_prepare() fails, it internally rollbacks adjacent list so that we don't need any other action. netdev_adjacent_change_commit() deletes old device in the adjacent list and allows new device to use. netdev_adjacent_change_abort() rollbacks adjacent list. Signed-off-by:
-
Taehee Yoo authored
When a macsec interface is created, it increases a refcnt to a lower device(real device). when macsec interface is deleted, the refcnt is decreased in macsec_free_netdev(), which is ->priv_destructor() of macsec interface. The problem scenario is this. When nested macsec interfaces are exiting, the exit routine of the macsec module makes refcnt leaks. Test commands: ip link add dummy0 type dummy ip link add macsec0 link dummy0 type macsec ip link add macsec1 link macsec0 type macsec modprobe -rv macsec [ 208.629433] unregister_netdevice: waiting for macsec0 to become free. Usage count = 1 Steps of exit routine of macsec module are below. 1. Calls ->dellink() in __rtnl_link_unregister(). 2. Checks refcnt and wait refcnt to be 0 if refcnt is not 0 in netdev_run_todo(). 3. Calls ->priv_destruvtor() in netdev_run_todo(). Step2 checks refcnt, but step3 decreases refcnt. So, step2 waits forever. This patch makes the macsec module do not hold a refcnt of the lower device because it already holds a refcnt of the lower device with netdev_upper_dev_link(). Fixes: c09440f7 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: -
Taehee Yoo authored
team interface could be nested and it's lock variable could be nested too. But this lock uses static lockdep key and there is no nested locking handling code such as mutex_lock_nested() and so on. so the Lockdep would warn about the circular locking scenario that couldn't happen. In order to fix, this patch makes the team module to use dynamic lock key instead of static key. Test commands: ip link add team0 type team ip link add team1 type team ip link set team0 master team1 ip link set team0 nomaster ip link set team1 master team0 ip link set team1 nomaster Splat that looks like: [ 40.364352] WARNING: possible recursive locking detected [ 40.364964] 5.4.0-rc3+ #96 Not tainted [ 40.365405] -------------------------------------------- [ 40.365973] ip/750 is trying to acquire lock: [ 40.366542] ffff888060b34c40 (&team->lock){+.+.}, at: team_set_mac_address+0x151/0x290 [team] [ 40.367689] but task is already holding lock: [ 40.368729] ffff888051201c40 (&team->lock){+.+.}, at: team_del_slave+0x29/0x60 [team] [ 40.370280] other info that might help us debug this: [ 40.371159] Possible unsafe locking scenario: [ 40.371942] CPU0 [ 40.372338] ---- [ 40.372673] lock(&team->lock); [ 40.373115] lock(&team->lock); [ 40.373549] *** DEADLOCK *** [ 40.374432] May be due to missing lock nesting notation [ 40.375338] 2 locks held by ip/750: [ 40.375851] #0: ffffffffabcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0 [ 40.376927] #1: ffff888051201c40 (&team->lock){+.+.}, at: team_del_slave+0x29/0x60 [team] [ 40.377989] stack backtrace: [ 40.378650] CPU: 0 PID: 750 Comm: ip Not tainted 5.4.0-rc3+ #96 [ 40.379368] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 40.380574] Call Trace: [ 40.381208] dump_stack+0x7c/0xbb [ 40.381959] __lock_acquire+0x269d/0x3de0 [ 40.382817] ? register_lock_class+0x14d0/0x14d0 [ 40.383784] ? check_chain_key+0x236/0x5d0 [ 40.384518] lock_acquire+0x164/0x3b0 [ 40.385074] ? team_set_mac_address+0x151/0x290 [team] [ 40.385805] __mutex_lock+0x14d/0x14c0 [ 40.386371] ? team_set_mac_address+0x151/0x290 [team] [ 40.387038] ? team_set_mac_address+0x151/0x290 [team] [ 40.387632] ? mutex_lock_io_nested+0x1380/0x1380 [ 40.388245] ? team_del_slave+0x60/0x60 [team] [ 40.388752] ? rcu_read_lock_sched_held+0x90/0xc0 [ 40.389304] ? rcu_read_lock_bh_held+0xa0/0xa0 [ 40.389819] ? lock_acquire+0x164/0x3b0 [ 40.390285] ? lockdep_rtnl_is_held+0x16/0x20 [ 40.390797] ? team_port_get_rtnl+0x90/0xe0 [team] [ 40.391353] ? __module_text_address+0x13/0x140 [ 40.391886] ? team_set_mac_address+0x151/0x290 [team] [ 40.392547] team_set_mac_address+0x151/0x290 [team] [ 40.393111] dev_set_mac_address+0x1f0/0x3f0 [ ... ] Fixes: 3d249d4c ("net: introduce ethernet teaming device") Signed-off-by:
-
