If the host buffers are freed before destroying MR in HW,
HW could try accessing these buffers. This could cause a host
crash. Fixing the code to avoid this condition.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch implements the following HW workarounds

1. The SQ depth needs to be augmented  by 128 + 1 to avoid running
   into an Out of order CQE issue
2. Workaround to handle the problem where the HW fast path engine continues
   to access DMA memory in retranmission mode even after the WQE has
   already been completed. If the HW reports this condition, driver detects
   it and posts a Fence WQE. The driver stops reporting the completions
   to stack until it receives completion  for Fence WQE.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Fixing a concurrency issue with creq handling. Each caller
was given a globally managed crsq element, which was
accessed outside a lock. This could result in corruption,
if lot of applications are simultaneously issuing Control Path
commands. Now, each caller will provide its own response buffer
and the responses will be copied under a lock.
Also, Fixing the queue full condition check for the CMDQ.

As a part of these changes, the control path code is refactored
to remove the code replication in the response status checking.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Commit eea40b8f ("infiniband: call ipv6 route lookup via the stub
interface") introduced a regression in address resolution when connecting
to IPv6 destination addresses.  The old code called ip6_route_output(),
while the new code calls ipv6_stub->ipv6_dst_lookup().  The two are almost
the same, except that ipv6_dst_lookup() also calls ip6_route_get_saddr()
if the source address is in6addr_any.

This means that the test of ipv6_addr_any(&fl6.saddr) now never succeeds,
and so we never copy the source address out.  This ends up causing
rdma_resolve_addr() to fail, because without a resolved source address,
cma_acquire_dev() will fail to find an RDMA device to use.  For me, this
causes connecting to an NVMe over Fabrics target via RoCE / IPv6 to fail.

Fix this by copying out fl6.saddr if ipv6_addr_any() is true for the original
source address passed into addr6_resolve().  We can drop our call to
ipv6_dev_get_saddr() because ipv6_dst_lookup() already does that work.

Fixes: eea40b8f ("infiniband: call ipv6 route lookup via the stub interface")
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Commit 9fdca4da (IB/SA: Split struct sa_path_rec based on IB and
ROCE specific fields) moved the service_id to be specific attribute
for IB and OPA SA Path Record, and thus wasn't assigned for RoCE.

This caused to the following kernel panic in the CMA request handler flow:

[   27.074594] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[   27.074731] IP: __radix_tree_lookup+0x1d/0xe0
...
[   27.075356] Workqueue: ib_cm cm_work_handler [ib_cm]
[   27.075401] task: ffff88022e3b8000 task.stack: ffffc90001298000
[   27.075449] RIP: 0010:__radix_tree_lookup+0x1d/0xe0
...
[   27.075979] Call Trace:
[   27.076015]  radix_tree_lookup+0xd/0x10
[   27.076055]  cma_ps_find+0x59/0x70 [rdma_cm]
[   27.076097]  cma_id_from_event+0xd2/0x470 [rdma_cm]
[   27.076144]  ? ib_init_ah_from_path+0x39a/0x590 [ib_core]
[   27.076193]  cma_req_handler+0x25/0x480 [rdma_cm]
[   27.076237]  cm_process_work+0x25/0x120 [ib_cm]
[   27.076280]  ? cm_get_bth_pkey.isra.62+0x3c/0xa0 [ib_cm]
[   27.076350]  cm_req_handler+0xb03/0xd40 [ib_cm]
[   27.076430]  ? sched_clock_cpu+0x11/0xb0
[   27.076478]  cm_work_handler+0x194/0x1588 [ib_cm]
[   27.076525]  process_one_work+0x160/0x410
[   27.076565]  worker_thread+0x137/0x4a0
[   27.076614]  kthread+0x112/0x150
[   27.076684]  ? max_active_store+0x60/0x60
[   27.077642]  ? kthread_park+0x90/0x90
[   27.078530]  ret_from_fork+0x2c/0x40

This patch moves it back to the common SA Path Record structure
and removes the redundant setter and getter.

Tested on Connect-IB and Connect-X4 in Infiniband and RoCE respectively.

Fixes: 9fdca4da (IB/SA: Split struct sa_path_rec based on IB ands
	ROCE specific fields)
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Add mmap_sem lock around VMA inspection in ib_umem_odp_get().

Fixes: 0008b84e ('IB/umem: Add support to huge ODP')
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This change will optimize kernel memory deregistration operations.
__ib_umem_release() used to call set_page_dirty_lock() against every
writable page in its memory region. Its purpose is to keep data
synced between CPU and DMA device when swapping happens after mem
deregistration ops. Now we choose not to set page dirty bit if it's
already set by kernel prior to calling __ib_umem_release(). This
reduces memory deregistration time by half or even more when we ran
application simulation test program.
Signed-off-by: Qing Huang <qing.huang@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Commit 57520751 ("IB/SA: Add OPA path record type") introduced
new local function __ib_copy_path_rec_to_user, but didn't limit its
scope. This produces the following sparse warning:

	drivers/infiniband/core/uverbs_marshall.c:99:6: warning:
	symbol '__ib_copy_path_rec_to_user' was not declared. Should it be
	static?

In addition, it used sizeof ... notations instead of sizeof(...), which
is correct in C, but a little bit misleading. Let's change it too.

Fixes: 57520751 ("IB/SA: Add OPA path record type")
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

RDMA netlink is part of ib_core, hence ibnl_chk_listeners(),
ibnl_init() and ibnl_cleanup() don't need to be published
in public header file.

Let's remove EXPORT_SYMBOL from ibnl_chk_listeners() and move all these
functions to private header file.

CC: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

If srp_init_qp() fails at srp_create_ch_ib() then ch->send_cq
may be NULL.
Calling directly to ib_destroy_qp() is sufficient because
no work requests were posted on the created qp.

Fixes: 9294000d ("IB/srp: Drain the send queue before destroying a QP")
Cc: <stable@vger.kernel.org>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Bart van Assche <bart.vanassche@sandisk.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>

ipoib_dev_uninit_default() call is used in ipoib_main.c file only
and it generates the following warning from smatch tool:
	drivers/infiniband/ulp/ipoib/ipoib_main.c:1593:6: warning:
	symbol 'ipoib_dev_uninit_default' was not declared. Should it
	be static?

so let's declare that function as static.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

ipoib_dev_init accesses the wrong private data for the IPoIB device.
Commit cd565b4b (IB/IPoIB: Support acceleration options callbacks)
changed ipoib_priv from being identical to netdev_priv to being an
area inside of, but not the same pointer as, the netdev_priv pointer.
As such, the struct we want is the ipoib_priv area, not the netdev_priv
area, so use the right accessor, otherwise we kernel panic.

[   27.271938] IPv6: ADDRCONF(NETDEV_CHANGE): mlx5_ib0.8006: link becomes ready
[   28.156790] BUG: unable to handle kernel NULL pointer dereference at 000000000000067c
[   28.166309] IP: ib_query_port+0x30/0x180 [ib_core]
...
[   28.306282] RIP: 0010:ib_query_port+0x30/0x180 [ib_core]
...
[   28.393337] Call Trace:
[   28.397594]  ipoib_get_link_ksettings+0x66/0xe0 [ib_ipoib]
[   28.405274]  __ethtool_get_link_ksettings+0xa0/0x1c0
[   28.412353]  speed_show+0x74/0xa0
[   28.417503]  dev_attr_show+0x20/0x50
[   28.422922]  ? mutex_lock+0x12/0x40
[   28.428179]  sysfs_kf_seq_show+0xbf/0x1a0
[   28.434002]  kernfs_seq_show+0x21/0x30
[   28.439470]  seq_read+0x116/0x3b0
[   28.444445]  ? do_filp_open+0xa5/0x100
[   28.449774]  kernfs_fop_read+0xff/0x180
[   28.455220]  __vfs_read+0x37/0x150
[   28.460167]  ? security_file_permission+0x9d/0xc0
[   28.466560]  vfs_read+0x8c/0x130
[   28.471318]  SyS_read+0x55/0xc0
[   28.475950]  do_syscall_64+0x67/0x150
[   28.481163]  entry_SYSCALL64_slow_path+0x25/0x25
...
[   28.584493] ---[ end trace 3549968a4bf0aa5d ]---

Fixes: cd565b4b (IB/IPoIB: Support acceleration options callbacks)
Fixes: 0d7e2d21 (IB/ipoib: add get_link_ksettings in ethtool)
Signed-off-by: Honggang Li <honli@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Add null check before dereferencing pointer sgid_attr.ndev
inside function rdma_vlan_dev_vlan_id().

Addresses-Coverity-ID: 1373979
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Cache the needed umr_fence and set the wqe ctrl segmennt
accordingly.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>

HW can implement UMR wqe re-transmission in various ways.
Thus, add HCA cap to distinguish the needed fence for UMR to make
sure that the wqe wouldn't fail on mkey checks.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The cited patch added a type field to structures ib_ah and rdma_ah_attr.

Function mlx4_ib_query_ah() builds an rdma_ah_attr structure from the
data in an mlx4_ib_ah structure (which contains both an ib_ah structure
and an address vector).

For mlx4_ib_query_ah() to work properly, the type field in the contained
ib_ah structure must be set correctly.

In the outgoing MAD tunneling flow, procedure mlx4_ib_multiplex_mad()
paravirtualizes a MAD received from a slave and sends the processed
mad out over the wire. During this processing, it populates an
mlx4_ib_ah structure and calls mlx4_ib_query_ah().

The cited commit overlooked setting the type field in the contained
ib_ah structure before invoking mlx4_ib_query_ah(). As a result, the
type field remained uninitialized, and the rdma_ah_attr structure was
incorrectly built. This resulted in improperly built MADs being sent out
over the wire.

This patch properly initializes the type field in the contained ib_ah
structure before calling mlx4_ib_query_ah(). The rdma_ah_attr structure
is then generated correctly.

Fixes: 44c58487 ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The handling of IB_RDMA_WRITE_ONLY_WITH_IMMEDIATE will leak a memory
reference when a buffer cannot be allocated for returning the immediate
data.

The issue is that the rkey validation has already occurred and the RNR
nak fails to release the reference that was fruitlessly gotten.  The
the peer will send the identical single packet request when its RNR
timer pops.

The fix is to release the held reference prior to the rnr nak exit.
This is the only sequence the requires both rkey validation and the
buffer allocation on the same packet.

Cc: Stable <stable@vger.kernel.org> # 4.7+
Tested-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Keep VL15 credits at 0 during LNI, before link-up. Store
VL15 credits value during verify cap interrupt and set
in after link-up. This addresses an issue where VL15 MAD
packets could be sent by one side of the link before
the other side is ready to receive them.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The Omni-Path adapter driver fails to load on the ppc64le platform
due to invalid PCI setup.

This patch makes the PCI configuration more robust and will
fix 64 bit addressing for ppc64le.
Signed-off-by: Steven L Roberts <robers97@gmail.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This fixes a kernel panic when loading the hfi driver as a dynamic module.
Signed-off-by: Steven L Roberts <robers97@gmail.com>
Reviewed-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Take care of ipv6 checks while computing header length for deducing mtu
size of ipv6 servers. Due to the incorrect header length computation for
ipv6 servers, wrong mss is reported to the peer (client).
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

use egrstatuspagesize to calculate t4_eq_status_entries.

Fixes: bb58d079 ("cxgb4: Update IngPad and IngPack values")
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The patch 761e19a5 (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure()) from May 6, 2016
leads to the following static checker warning:
	drivers/infiniband/hw/cxgb4/cm.c:575 abort_arp_failure()
	warn: passing freed memory 'skb'

Also fixes skb leak when l2t resolution fails

Fixes: 761e19a5 (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure())
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Explicitly ACK the MPA Reply frame so the peer
does not retransmit the frame.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Don't set control flag for 0-length FULPDU (Send) RTR indication
in the enhanced MPA Request/Reply frames, because it isn't supported.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Refactor code to avoid identical code for different branches.

Addresses-Coverity-ID: 1357356
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

MSS change on active QPs is not supported. Store new MSS
value for new QPs only. Remove code to modify MSS on the fly.
This also resolves a crash on QP modify to QP 0.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: i40iw_sc_qp_modify+0x22/0x280 [i40iw]
Oops: 0000 [#1] SMP KASAN
CPU: 2 PID: 1236 Comm: kworker/u16:4 Not tainted 4.12.0-rc1 #5
Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./Q87M-D2H,
BIOS F7 01/17/2014
Workqueue: l2params i40iw_l2params_worker [i40iw]
task: ffff88070f5a9b40 task.stack: ffff88070f5a0000
RIP: 0010:i40iw_sc_qp_modify+0x22/0x280 [i40iw]
...
Call Trace:
i40iw_exec_cqp_cmd+0x2ce/0x410 [i40iw]
? _raw_spin_lock_irqsave+0x6f/0x80
? i40iw_process_cqp_cmd+0x1d/0x80 [i40iw]
i40iw_process_cqp_cmd+0x7c/0x80 [i40iw]
i40iw_handle_cqp_op+0x2f/0x200 [i40iw]
? trace_hardirqs_off+0xd/0x10
? _raw_spin_unlock_irqrestore+0x46/0x50
i40iw_hw_modify_qp+0x5e/0x90 [i40iw]
i40iw_qp_mss_modify+0x52/0x60 [i40iw]
i40iw_change_l2params+0x145/0x160 [i40iw]
i40iw_l2params_worker+0x1f/0x40 [i40iw]
process_one_work+0x1f5/0x650
? process_one_work+0x161/0x650
worker_thread+0x48/0x3b0
kthread+0x112/0x150
? process_one_work+0x650/0x650
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x2e/0x40
Code: 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 41 56 41 55 41 89 cd 41 54 49 89 fc
53 48 89 f3 48 89 d6 48 83 ec 08 48 8b 87 10 01 00 00 <48> 8b 40 08 4c 8b b0 40 04
00 00 4c 89 f7 e8 1b e5 ff ff 48 85
RIP: i40iw_sc_qp_modify+0x22/0x280 [i40iw] RSP: ffff88070f5a7c28
CR2: 0000000000000008
---[ end trace 77a405931e296060 ]---
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Some error paths in i40iw_initialize_dev are doing
additional and unnecessary work before exiting.
Correctly free resources allocated prior to error
and return with correct status code.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intelcom>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Explicitly ACK the MPA Reject frame so the peer does
not retransmit the frame.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Don't set control flag for 0-length FULPDU (Send)
RTR indication in the enhanced MPA Request/Reply
frames, because it isn't supported.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull thermal SoC management fixes from Eduardo Valentin:

 - fixes to TI SoC driver, Broadcom, qoriq

 - small sparse warning fix on thermal core

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: broadcom: ns-thermal: default on iProc SoCs
  ti-soc-thermal: Fix a typo in a comment line
  ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
  ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
  thermal: core: make thermal_emergency_poweroff static
  thermal: qoriq: remove useless call for of_thermal_get_trip_points()

Pull tty/serial fixes from Greg KH:
 "Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
  than normal, which is why I had them bake in linux-next for a few
  weeks and didn't send them to you for -rc2.

  They revert a few of the serdev patches from 4.12-rc1, and bring
  things back to how they were in 4.11, to try to make things a bit more
  stable there. Rob and Johan both agree that this is the way forward,
  so this isn't people squabbling over semantics. Other than that, just
  a few minor serial driver fixes that people have had problems with.

  All of these have been in linux-next for a few weeks with no reported
  issues"

* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: altera_uart: call iounmap() at driver remove
  serial: imx: ensure UCR3 and UFCR are setup correctly
  MAINTAINERS/serial: Change maintainer of jsm driver
  serial: enable serdev support
  tty/serdev: add serdev registration interface
  serdev: Restore serdev_device_write_buf for atomic context
  serial: core: fix crash in uart_suspend_port
  tty: fix port buffer locking
  tty: ehv_bytechan: clean up init error handling
  serial: ifx6x60: fix use-after-free on module unload
  serial: altera_jtaguart: adding iounmap()
  serial: exar: Fix stuck MSIs
  serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
  serdev: fix tty-port client deregistration
  Revert "tty_port: register tty ports with serdev bus"
  drivers/tty: 8250: only call fintek_8250_probe when doing port I/O

Pull powerpc fixes from Michael Ellerman:
 "Fix running SPU programs on Cell, and a few other minor fixes.

  Thanks to Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas
  Piggin"

* tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions
  powerpc/spufs: Fix hash faults for kernel regions
  powerpc: Fix booting P9 hash with CONFIG_PPC_RADIX_MMU=N
  powerpc/powernv/npu-dma.c: Fix opal_npu_destroy_context() call
  selftests/powerpc: Fix TM resched DSCR test with some compilers

Pull x86 fixes from Thomas Gleixner:
 "A series of fixes for X86:

   - The final fix for the end-of-stack issue in the unwinder
   - Handle non PAT systems gracefully
   - Prevent access to uninitiliazed memory
   - Move early delay calaibration after basic init
   - Fix Kconfig help text
   - Fix a cross compile issue
   - Unbreak older make versions"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
  x86/alternatives: Prevent uninitialized stack byte read in apply_alternatives()
  x86/PAT: Fix Xorg regression on CPUs that don't support PAT
  x86/watchdog: Fix Kconfig help text file path reference to lockup watchdog documentation
  x86/build: Permit building with old make versions
  x86/unwind: Add end-of-stack check for ftrace handlers
  Revert "x86/entry: Fix the end of the stack for newly forked tasks"
  x86/boot: Use CROSS_COMPILE prefix for readelf

Pull timer fixlet from Thomas Gleixner:
 "Silence dmesg spam by making the posix cpu timer printks depend on
  print_fatal_signals"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-timers: Make signal printks conditional

Pull RAS fixes from Thomas Gleixner:
 "Two fixlets for RAS:

   - Export memory_error() so the NFIT module can utilize it

   - Handle memory errors in NFIT correctly"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  acpi, nfit: Fix the memory error check in nfit_handle_mce()
  x86/MCE: Export memory_error()

Pull perf tooling fixes from Thomas Gleixner:

 - Synchronization of tools and kernel headers

 - A series of fixes for perf report addressing various failures:
    * Handle invalid maps proper
    * Plug a memory leak
    * Handle frames and callchain order correctly

 - Fixes for handling inlines and children mode

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/include: Sync kernel ABI headers with tooling headers
  perf tools: Put caller above callee in --children mode
  perf report: Do not drop last inlined frame
  perf report: Always honor callchain order for inlined nodes
  perf script: Add --inline option for debugging
  perf report: Fix off-by-one for non-activation frames
  perf report: Fix memory leak in addr2line when called by addr2inlines
  perf report: Don't crash on invalid maps in `-g srcline` mode

Pull locking fix from Thomas Gleixner:
 "A fix for a state leak which was introduced in the recent rework of
  futex/rtmutex interaction"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()

Pull kthread fix from Thomas Gleixner:
 "A single fix which prevents a use after free when kthread fork fails"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kthread: Fix use-after-free if kthread fork fails