- 30 May, 2019 4 commits
-
-
Lianbo Jiang authored
When SME is enabled, the smartpqi driver won't work on the HP DL385 G10 machine, which causes the failure of kernel boot because it fails to allocate pqi error buffer. Please refer to the kernel log: .... [ 9.431749] usbcore: registered new interface driver uas [ 9.441524] Microsemi PQI Driver (v1.1.4-130) [ 9.442956] i40e 0000:04:00.0: fw 6.70.48768 api 1.7 nvm 10.2.5 [ 9.447237] smartpqi 0000:23:00.0: Microsemi Smart Family Controller found Starting dracut initqueue hook... [ OK ] Started Show Plymouth Boot Scre[ 9.471654] Broadcom NetXtreme-C/E driver bnxt_en v1.9.1 en. [ OK ] Started Forward Password Requests to Plymouth Directory Watch. [[0;[ 9.487108] smartpqi 0000:23:00.0: failed to allocate PQI error buffer .... [ 139.050544] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts [ 139.589779] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts Basically, the fact that the coherent DMA mask value wasn't set caused the driver to fall back to SWIOTLB when SME is active. For correct operation, lets call the dma_set_mask_and_coherent() to properly set the mask for both streaming and coherent, in order to inform the kernel about the devices DMA addressing capabilities. Signed-off-by:Lianbo Jiang <lijiang@redhat.com> Acked-by:
Don Brace <don.brace@microsemi.com> Tested-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Steffen Maier authored
When the user tries to remove a zfcp port via sysfs, we only rejected it if there are zfcp unit children under the port. With purely automatically scanned LUNs there are no zfcp units but only SCSI devices. In such cases, the port_remove erroneously continued. We close the port and this implicitly closes all LUNs under the port. The SCSI devices survive with their private zfcp_scsi_dev still holding a reference to the "removed" zfcp_port (still allocated but invisible in sysfs) [zfcp_get_port_by_wwpn in zfcp_scsi_slave_alloc]. This is not a problem as long as the fc_rport stays blocked. Once (auto) port scan brings back the removed port, we unblock its fc_rport again by design. However, there is no mechanism that would recover (open) the LUNs under the port (no "ersfs_3" without zfcp_unit [zfcp_erp_strategy_followup_success]). Any pending or new I/O to such LUN leads to repeated: Done: NEEDS_RETRY Result: hostbyte=DID_IMM_RETRY driverbyte=DRIVER_OK See also v4.10 commit 6f2ce1c6 ("scsi: zfcp: fix rport unblock race with LUN recovery"). Even a manual LUN recovery (echo 0 > /sys/bus/scsi/devices/H:C:T:L/zfcp_failed) does not help, as the LUN links to the old "removed" port which remains to lack ZFCP_STATUS_COMMON_RUNNING [zfcp_erp_required_act]. The only workaround is to first ensure that the fc_rport is blocked (e.g. port_remove again in case it was re-discovered by (auto) port scan), then delete the SCSI devices, and finally re-discover by (auto) port scan. The port scan includes an fc_rport unblock, which in turn triggers a new scan on the scsi target to freshly get new pure auto scan LUNs. Fix this by rejecting port_remove also if there are SCSI devices (even without any zfcp_unit) under this port. Re-use mechanics from v3.7 commit d99b601b ("[SCSI] zfcp: restore refcount check on port_remove"). However, we have to give up zfcp_sysfs_port_units_mutex earlier in unit_add to prevent a deadlock with scsi_host scan taking shost->scan_mutex first and then zfcp_sysfs_port_units_mutex now in our zfcp_scsi_slave_alloc(). Signed-off-by:
Steffen Maier <maier@linux.ibm.com> Fixes: b62a8d9b ("[SCSI] zfcp: Use SCSI device data zfcp scsi dev instead of zfcp unit") Fixes: f8210e34 ("[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode") Cc: <stable@vger.kernel.org> #2.6.37+ Reviewed-by:
Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
-
Steffen Maier authored
With this early return due to zfcp_unit child(ren), we don't use the zfcp_port reference from the earlier zfcp_get_port_by_wwpn() anymore and need to put it. Signed-off-by:
Jens Remus <jremus@linux.ibm.com> Reviewed-by:
-
Varun Prakash authored
ip_dev_find() can return NULL so add a check for NULL pointer. Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
- 20 May, 2019 4 commits
-
-
Martin K. Petersen authored
This reverts commit 20bd1d02. This patch introduced regressions for devices that come online in read-only state and subsequently switch to read-write. Given how the partition code is currently implemented it is not possible to persist the read-only flag across a device revalidate call. This may need to get addressed in the future since it is common for user applications to proactively call BLKRRPART. Reverting this commit will re-introduce a regression where a device-initiated revalidate event will cause the admin state to be forgotten. A separate patch will address this issue. Fixes: 20bd1d02 ("scsi: sd: Keep disk read-only when re-reading partition") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Colin Ian King authored
Currently an int is being shifted and the result is being cast to a u64 which leads to undefined behaviour if the shift is more than 31 bits. Fix this by casting the integer value 1 to u64 before the shift operation. Addresses-Coverity: ("Bad shift operation") Fixes: 7b594769 ("[SCSI] bnx2fc: Handle REC_TOV error code from firmware") Signed-off-by:Colin Ian King <colin.king@canonical.com> Acked-by:
Saurav Kashyap <skashyap@marvell.com> Signed-off-by:
-
Erwan Velu authored
When a HARDWARE_ERROR is triggered for ASC=0x3e, the existing code is only considering the case where ASCQ=0x1. According to the http://www.t10.org/lists/asc-num.htm#ASC_3E specification, other values may occur like a timeout (ASCQ=0x2). This patch prints an error message when a non-handled message is received. This can help diagnose a possible misbehavior of the controller or a missing implementation in the Linux kernel. This patch keeps the exact same error handling but prints a message if an ASCQ != 1 is reported. [mkp: clarified commit message] Signed-off-by:
Erwan Velu <e.velu@criteo.com> Acked-by:
-
YueHaibing authored
drivers/scsi/myrs.c: In function 'myrs_log_event': drivers/scsi/myrs.c:821:24: warning: 'sshdr.sense_key' may be used uninitialized in this function [-Wmaybe-uninitialized] struct scsi_sense_hdr sshdr; If ev->ev_code is not 0x1C, sshdr.sense_key may be used uninitialized. Fix this by initializing variable 'sshdr' to 0. Fixes: 77266186 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
- 14 May, 2019 7 commits
-
-
James Smart authored
Due to the couple of bug fixes, update lpfc version to 12.2.0.2 Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Tested-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
James Smart authored
There was a missing qualification of a valid ndlp structure when calling to send an RRQ for an abort. Add the check. Signed-off-by:
-
James Smart authored
Many of the exit cases were not releasing the rcu read lock. Corrected the exit paths. Signed-off-by:
-
James Smart authored
There were a number of erroneous comments and incorrect older lockdep checks that were causing a number of warnings. Resolve the following: - Inconsistent lock state warnings in lpfc_nvme_info_show(). - Fixed comments and code on sequences where ring lock is now held instead of hbalock. - Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than locking prior to the routine and have routine guess on what lock, take the lock within the routine. The lockdep check becomes unnecessary. - Fixed comments and removed erroneous hbalock checks. Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/qedi/qedi_iscsi.c: In function 'qedi_ep_connect': drivers/scsi/qedi/qedi_iscsi.c:813:23: warning: variable 'udev' set but not used [-Wunused-but-set-variable] drivers/scsi/qedi/qedi_iscsi.c:812:18: warning: variable 'cdev' set but not used [-Wunused-but-set-variable] These have never been used since introduction. Signed-off-by:
Manish Rangankar <mrangankar@marvell.com> Signed-off-by:
-
YueHaibing authored
KASAN reports this: BUG: KASAN: global-out-of-bounds in qedi_dbg_err+0xda/0x330 [qedi] Read of size 31 at addr ffffffffc12b0ae0 by task syz-executor.0/2429 CPU: 0 PID: 2429 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xfa/0x1ce lib/dump_stack.c:113 print_address_description+0x1c4/0x270 mm/kasan/report.c:187 kasan_report+0x149/0x18d mm/kasan/report.c:317 memcpy+0x1f/0x50 mm/kasan/common.c:130 qedi_dbg_err+0xda/0x330 [qedi] ? 0xffffffffc12d0000 qedi_init+0x118/0x1000 [qedi] ? 0xffffffffc12d0000 ? 0xffffffffc12d0000 ? 0xffffffffc12d0000 do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x462e99 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f2d57e55c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000000000073bfa0 RCX: 0000000000462e99 RDX: 0000000000000000 RSI: 00000000200003c0 RDI: 0000000000000003 RBP: 00007f2d57e55c70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f2d57e566bc R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004 The buggy address belongs to the variable: __func__.67584+0x0/0xffffffffffffd520 [qedi] Memory state around the buggy address: ffffffffc12b0980: fa fa fa fa 00 04 fa fa fa fa fa fa 00 00 05 fa ffffffffc12b0a00: fa fa fa fa 00 00 04 fa fa fa fa fa 00 05 fa fa > ffffffffc12b0a80: fa fa fa fa 00 06 fa fa fa fa fa fa 00 02 fa fa ^ ffffffffc12b0b00: fa fa fa fa 00 00 04 fa fa fa fa fa 00 00 03 fa ffffffffc12b0b80: fa fa fa fa 00 00 02 fa fa fa fa fa 00 00 04 fa Currently the qedi_dbg_* family of functions can overrun the end of the source string if it is less than the destination buffer length because of the use of a fixed sized memcpy. Remove the memset/memcpy calls to nfunc and just use func instead as it is always a null terminated string. Reported-by:Hulk Robot <hulkci@huawei.com> Fixes: ace7f46b ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Quinn Tran authored
During EEH error recovery testing it was discovered that driver's reset() callback partially frees resources used by driver, leaving some stale memory. After reset() is done and when resume() callback in driver uses old data which results into error leaving adapter disabled due to PCIe error. This patch does cleanup for EEH recovery code path and prevents adapter from getting disabled. Signed-off-by:
Quinn Tran <qutran@marvell.com> Signed-off-by:
Himanshu Madhani <hmadhani@marvell.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
- 29 Apr, 2019 25 commits
-
-
Bart Van Assche authored
This patch avoids that lockdep reports the following warning: ===================================================== WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected 5.1.0-rc1-dbg+ #11 Tainted: G W ----------------------------------------------------- rmdir/1478 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: 00000000e7ac4607 (&(&k->k_lock)->rlock){+.+.}, at: klist_next+0x43/0x1d0 and this task is already holding: 00000000cf0baf5e (&(&ha->tgt.sess_lock)->rlock){-...}, at: tcm_qla2xxx_close_session+0x57/0xb0 [tcm_qla2xxx] which would create a new lock dependency: (&(&ha->tgt.sess_lock)->rlock){-...} -> (&(&k->k_lock)->rlock){+.+.} but this new dependency connects a HARDIRQ-irq-safe lock: (&(&ha->tgt.sess_lock)->rlock){-...} ... which became HARDIRQ-irq-safe at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 qla2x00_fcport_event_handler+0x1f3d/0x22b0 [qla2xxx] qla2x00_async_login_sp_done+0x1dc/0x1f0 [qla2xxx] qla24xx_process_response_queue+0xa37/0x10e0 [qla2xxx] qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx] __handle_irq_event_percpu+0x79/0x3c0 handle_irq_event_percpu+0x70/0xf0 handle_irq_event+0x5a/0x8b handle_edge_irq+0x12c/0x310 handle_irq+0x192/0x20a do_IRQ+0x73/0x160 ret_from_intr+0x0/0x1d default_idle+0x23/0x1f0 arch_cpu_idle+0x15/0x20 default_idle_call+0x35/0x40 do_idle+0x2bb/0x2e0 cpu_startup_entry+0x1d/0x20 start_secondary+0x24d/0x2d0 secondary_startup_64+0xa4/0xb0 to a HARDIRQ-irq-unsafe lock: (&(&k->k_lock)->rlock){+.+.} ... which became HARDIRQ-irq-unsafe at: ... lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7f4/0xb60 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 other info that might help us debug this: Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&k->k_lock)->rlock); local_irq_disable(); lock(&(&ha->tgt.sess_lock)->rlock); lock(&(&k->k_lock)->rlock); <Interrupt> lock(&(&ha->tgt.sess_lock)->rlock); *** DEADLOCK *** 4 locks held by rmdir/1478: #0: 000000002c7f1ba4 (sb_writers#10){.+.+}, at: mnt_want_write+0x32/0x70 #1: 00000000c85eb147 (&default_group_class[depth - 1]#2/1){+.+.}, at: do_rmdir+0x217/0x2d0 #2: 000000002b164d6f (&sb->s_type->i_mutex_key#13){++++}, at: vfs_rmdir+0x7e/0x1d0 #3: 00000000cf0baf5e (&(&ha->tgt.sess_lock)->rlock){-...}, at: tcm_qla2xxx_close_session+0x57/0xb0 [tcm_qla2xxx] the dependencies between HARDIRQ-irq-safe lock and the holding lock: -> (&(&ha->tgt.sess_lock)->rlock){-...} ops: 127 { IN-HARDIRQ-W at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 qla2x00_fcport_event_handler+0x1f3d/0x22b0 [qla2xxx] qla2x00_async_login_sp_done+0x1dc/0x1f0 [qla2xxx] qla24xx_process_response_queue+0xa37/0x10e0 [qla2xxx] qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx] __handle_irq_event_percpu+0x79/0x3c0 handle_irq_event_percpu+0x70/0xf0 handle_irq_event+0x5a/0x8b handle_edge_irq+0x12c/0x310 handle_irq+0x192/0x20a do_IRQ+0x73/0x160 ret_from_intr+0x0/0x1d default_idle+0x23/0x1f0 arch_cpu_idle+0x15/0x20 default_idle_call+0x35/0x40 do_idle+0x2bb/0x2e0 cpu_startup_entry+0x1d/0x20 start_secondary+0x24d/0x2d0 secondary_startup_64+0xa4/0xb0 INITIAL USE at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 qla2x00_loop_resync+0xb3d/0x2690 [qla2xxx] qla2x00_do_dpc+0xcee/0xf30 [qla2xxx] kthread+0x1d2/0x1f0 ret_from_fork+0x3a/0x50 } ... key at: [<ffffffffa125f700>] __key.62804+0x0/0xfffffffffff7e900 [qla2xxx] ... acquired at: __lock_acquire+0x11ed/0x1b60 lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 klist_next+0x43/0x1d0 device_for_each_child+0x96/0x110 scsi_target_block+0x3c/0x40 [scsi_mod] fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc] qla2x00_mark_device_lost+0x4d3/0x500 [qla2xxx] qlt_unreg_sess+0x104/0x2c0 [qla2xxx] tcm_qla2xxx_close_session+0xa2/0xb0 [tcm_qla2xxx] target_shutdown_sessions+0x17b/0x190 [target_core_mod] core_tpg_del_initiator_node_acl+0xf3/0x1f0 [target_core_mod] target_fabric_nacl_base_release+0x25/0x30 [target_core_mod] config_item_release+0x9f/0x120 [configfs] config_item_put+0x29/0x2b [configfs] configfs_rmdir+0x3d2/0x520 [configfs] vfs_rmdir+0xb3/0x1d0 do_rmdir+0x25c/0x2d0 __x64_sys_rmdir+0x24/0x30 do_syscall_64+0x77/0x220 entry_SYSCALL_64_after_hwframe+0x49/0xbe the dependencies between the lock to be acquired and HARDIRQ-irq-unsafe lock: -> (&(&k->k_lock)->rlock){+.+.} ops: 14568 { HARDIRQ-ON-W at: lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7f4/0xb60 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 SOFTIRQ-ON-W at: lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7f4/0xb60 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 INITIAL USE at: lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7f4/0xb60 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 } ... key at: [<ffffffff83f3d900>] __key.15805+0x0/0x40 ... acquired at: __lock_acquire+0x11ed/0x1b60 lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 klist_next+0x43/0x1d0 device_for_each_child+0x96/0x110 scsi_target_block+0x3c/0x40 [scsi_mod] fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc] qla2x00_mark_device_lost+0x4d3/0x500 [qla2xxx] qlt_unreg_sess+0x104/0x2c0 [qla2xxx] tcm_qla2xxx_close_session+0xa2/0xb0 [tcm_qla2xxx] target_shutdown_sessions+0x17b/0x190 [target_core_mod] core_tpg_del_initiator_node_acl+0xf3/0x1f0 [target_core_mod] target_fabric_nacl_base_release+0x25/0x30 [target_core_mod] config_item_release+0x9f/0x120 [configfs] config_item_put+0x29/0x2b [configfs] configfs_rmdir+0x3d2/0x520 [configfs] vfs_rmdir+0xb3/0x1d0 do_rmdir+0x25c/0x2d0 __x64_sys_rmdir+0x24/0x30 do_syscall_64+0x77/0x220 entry_SYSCALL_64_after_hwframe+0x49/0xbe stack backtrace: CPU: 7 PID: 1478 Comm: rmdir Tainted: G W 5.1.0-rc1-dbg+ #11 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x86/0xca check_usage.cold.59+0x473/0x563 check_prev_add.constprop.43+0x1f1/0x1170 __lock_acquire+0x11ed/0x1b60 lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 klist_next+0x43/0x1d0 device_for_each_child+0x96/0x110 scsi_target_block+0x3c/0x40 [scsi_mod] fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc] qla2x00_mark_device_lost+0x4d3/0x500 [qla2xxx] qlt_unreg_sess+0x104/0x2c0 [qla2xxx] tcm_qla2xxx_close_session+0xa2/0xb0 [tcm_qla2xxx] target_shutdown_sessions+0x17b/0x190 [target_core_mod] core_tpg_del_initiator_node_acl+0xf3/0x1f0 [target_core_mod] target_fabric_nacl_base_release+0x25/0x30 [target_core_mod] config_item_release+0x9f/0x120 [configfs] config_item_put+0x29/0x2b [configfs] configfs_rmdir+0x3d2/0x520 [configfs] vfs_rmdir+0xb3/0x1d0 do_rmdir+0x25c/0x2d0 __x64_sys_rmdir+0x24/0x30 do_syscall_64+0x77/0x220 entry_SYSCALL_64_after_hwframe+0x49/0xbe Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by: -
Bart Van Assche authored
The "(&ctio->u.status1.sense_data)[i]" where i >= 0 expressions in qlt_send_resp_ctio() are probably typos and should have been "(&ctio->u.status1.sense_data[4 * i])" instead. Instead of only fixing these typos, modify the code for storing sense data such that it becomes easy to read. This patch fixes a Coverity complaint about accessing an array outside its bounds. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: be25152c ("qla2xxx: Improve T10-DIF/PI handling in driver.") # v4.11. Signed-off-by:
-
Bart Van Assche authored
Since fc_remote_port_delete() must be called with interrupts enabled, do not disable interrupts when calling that function. Remove the lockin calls from around the put_sess() call. This is safe because the function that is called when the final reference is dropped, qlt_unreg_sess(), grabs the proper locks. This patch avoids that lockdep reports the following: WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected kworker/2:1/62 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: 0000000009e679b3 (&(&k->k_lock)->rlock){+.+.}, at: klist_next+0x43/0x1d0 and this task is already holding: 00000000a033b71c (&(&ha->tgt.sess_lock)->rlock){-...}, at: qla24xx_delete_sess_fn+0x55/0xf0 [qla2xxx_scst] which would create a new lock dependency: (&(&ha->tgt.sess_lock)->rlock){-...} -> (&(&k->k_lock)->rlock){+.+.} but this new dependency connects a HARDIRQ-irq-safe lock: (&(&ha->tgt.sess_lock)->rlock){-...} ... which became HARDIRQ-irq-safe at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 qla24xx_report_id_acquisition+0xa69/0xe30 [qla2xxx_scst] qla24xx_process_response_queue+0x69e/0x1270 [qla2xxx_scst] qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx_scst] __handle_irq_event_percpu+0x79/0x3c0 handle_irq_event_percpu+0x70/0xf0 handle_irq_event+0x5a/0x8b handle_edge_irq+0x12c/0x310 handle_irq+0x192/0x20a do_IRQ+0x73/0x160 ret_from_intr+0x0/0x1d default_idle+0x23/0x1f0 arch_cpu_idle+0x15/0x20 default_idle_call+0x35/0x40 do_idle+0x2bb/0x2e0 cpu_startup_entry+0x1d/0x20 start_secondary+0x2a8/0x320 secondary_startup_64+0xa4/0xb0 to a HARDIRQ-irq-unsafe lock: (&(&k->k_lock)->rlock){+.+.} ... which became HARDIRQ-irq-unsafe at: ... lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7e1/0xb50 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 other info that might help us debug this: Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&k->k_lock)->rlock); local_irq_disable(); lock(&(&ha->tgt.sess_lock)->rlock); lock(&(&k->k_lock)->rlock); <Interrupt> lock(&(&ha->tgt.sess_lock)->rlock); *** DEADLOCK *** 3 locks held by kworker/2:1/62: #0: 00000000a4319c16 ((wq_completion)"qla2xxx_wq"){+.+.}, at: process_one_work+0x437/0xa80 #1: 00000000ffa34c42 ((work_completion)(&sess->del_work)){+.+.}, at: process_one_work+0x437/0xa80 #2: 00000000a033b71c (&(&ha->tgt.sess_lock)->rlock){-...}, at: qla24xx_delete_sess_fn+0x55/0xf0 [qla2xxx_scst] the dependencies between HARDIRQ-irq-safe lock and the holding lock: -> (&(&ha->tgt.sess_lock)->rlock){-...} ops: 8 { IN-HARDIRQ-W at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 qla24xx_report_id_acquisition+0xa69/0xe30 [qla2xxx_scst] qla24xx_process_response_queue+0x69e/0x1270 [qla2xxx_scst] qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx_scst] __handle_irq_event_percpu+0x79/0x3c0 handle_irq_event_percpu+0x70/0xf0 handle_irq_event+0x5a/0x8b handle_edge_irq+0x12c/0x310 handle_irq+0x192/0x20a do_IRQ+0x73/0x160 ret_from_intr+0x0/0x1d default_idle+0x23/0x1f0 arch_cpu_idle+0x15/0x20 default_idle_call+0x35/0x40 do_idle+0x2bb/0x2e0 cpu_startup_entry+0x1d/0x20 start_secondary+0x2a8/0x320 secondary_startup_64+0xa4/0xb0 INITIAL USE at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 qla24xx_report_id_acquisition+0xa69/0xe30 [qla2xxx_scst] qla24xx_process_response_queue+0x69e/0x1270 [qla2xxx_scst] qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx_scst] __handle_irq_event_percpu+0x79/0x3c0 handle_irq_event_percpu+0x70/0xf0 handle_irq_event+0x5a/0x8b handle_edge_irq+0x12c/0x310 handle_irq+0x192/0x20a do_IRQ+0x73/0x160 ret_from_intr+0x0/0x1d default_idle+0x23/0x1f0 arch_cpu_idle+0x15/0x20 default_idle_call+0x35/0x40 do_idle+0x2bb/0x2e0 cpu_startup_entry+0x1d/0x20 start_secondary+0x2a8/0x320 secondary_startup_64+0xa4/0xb0 } ... key at: [<ffffffffa0c0d080>] __key.85462+0x0/0xfffffffffff7df80 [qla2xxx_scst] ... acquired at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 klist_next+0x43/0x1d0 device_for_each_child+0x96/0x110 scsi_target_block+0x3c/0x40 [scsi_mod] fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc] qla2x00_mark_device_lost+0xa0b/0xa30 [qla2xxx_scst] qlt_unreg_sess+0x1c6/0x380 [qla2xxx_scst] qla24xx_delete_sess_fn+0xe6/0xf0 [qla2xxx_scst] process_one_work+0x511/0xa80 worker_thread+0x67/0x5b0 kthread+0x1d2/0x1f0 ret_from_fork+0x3a/0x50 the dependencies between the lock to be acquired and HARDIRQ-irq-unsafe lock: -> (&(&k->k_lock)->rlock){+.+.} ops: 13831 { HARDIRQ-ON-W at: lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7e1/0xb50 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 SOFTIRQ-ON-W at: lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7e1/0xb50 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 INITIAL USE at: lock_acquire+0xe3/0x200 _raw_spin_lock+0x32/0x50 klist_add_tail+0x33/0xb0 device_add+0x7e1/0xb50 device_create_groups_vargs+0x11c/0x150 device_create_with_groups+0x89/0xb0 vtconsole_class_init+0xb2/0x124 do_one_initcall+0xc5/0x3ce kernel_init_freeable+0x295/0x32e kernel_init+0x11/0x11b ret_from_fork+0x3a/0x50 } ... key at: [<ffffffff83ed8780>] __key.15491+0x0/0x40 ... acquired at: lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 klist_next+0x43/0x1d0 device_for_each_child+0x96/0x110 scsi_target_block+0x3c/0x40 [scsi_mod] fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc] qla2x00_mark_device_lost+0xa0b/0xa30 [qla2xxx_scst] qlt_unreg_sess+0x1c6/0x380 [qla2xxx_scst] qla24xx_delete_sess_fn+0xe6/0xf0 [qla2xxx_scst] process_one_work+0x511/0xa80 worker_thread+0x67/0x5b0 kthread+0x1d2/0x1f0 ret_from_fork+0x3a/0x50 stack backtrace: CPU: 2 PID: 62 Comm: kworker/2:1 Tainted: G O 5.0.7-dbg+ #8 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Workqueue: qla2xxx_wq qla24xx_delete_sess_fn [qla2xxx_scst] Call Trace: dump_stack+0x86/0xca check_usage.cold.52+0x473/0x563 __lock_acquire+0x11c0/0x23e0 lock_acquire+0xe3/0x200 _raw_spin_lock_irqsave+0x3d/0x60 klist_next+0x43/0x1d0 device_for_each_child+0x96/0x110 scsi_target_block+0x3c/0x40 [scsi_mod] fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc] qla2x00_mark_device_lost+0xa0b/0xa30 [qla2xxx_scst] qlt_unreg_sess+0x1c6/0x380 [qla2xxx_scst] qla24xx_delete_sess_fn+0xe6/0xf0 [qla2xxx_scst] process_one_work+0x511/0xa80 worker_thread+0x67/0x5b0 kthread+0x1d2/0x1f0 ret_from_fork+0x3a/0x50 Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by: -
Bart Van Assche authored
A reference count underflow is a severe bug. Hence complain loudly if a reference count underflow happens. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
This patch makes the code easier to read and more compact. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Introduce two structures for the (DMA address, length) combination instead of using separate structure members for the DMA address and length. This patch fixes several Coverity complaints about 'cur_dsd' being used to write outside the bounds of structure members. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Since the next patch will modify several firmware data structures, add compile time checks that verify that these structures have the correct size. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Pass dsd_list_len in little endian format to the firmware instead of in CPU endian format. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
In the *_done() functions, instead of returning early if sp->ref_count >= 2, only decrement sp->ref_count. In qla2xxx_eh_abort(), instead of deciding what to do based on the value of sp->ref_count, decide which action to take depending on the completion status of the firmware abort. Remove srb.cwaitq and use srb.comp instead. In qla2x00_abort_srb(), call isp_ops->abort_command() directly instead of calling qla2xxx_eh_abort(). Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
This patch reduces the size of struct srb. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Since qla24xx_async_abort_cmd() is only called from inside qla_init.c, declare that function static. Reorder a few functions to avoid that any forward declarations are needed. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
All callbacks from the target core into the qla2xxx driver and also all I/O completion functions are serialized per command. Since .cmd_sent_to_fw and .trc_flags are only modified from inside these functions it is not necessary to protect it with locking. Remove the superfluous locking. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Since the previous patch removed the only statement that sets qla_tgt_cmd.released, remove the code that depends on that member variable being set and the member variable itself. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
The previous patch guarantees that a command is only released after the firmware has finished processing it. Hence complain if a command is released that is owned by the firmware. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Remove the function qlt_abort_cmd_on_host_reset() because it can do the following, all of which can cause a kernel crash: - DMA unmapping while DMA is in progress. - Call target_execute_cmd() while DMA is in progress. - Call transport_generic_free_cmd() while the LIO core owns a command. Instead of trying to abort a command asynchronously, set the 'aborted' flag and handle the abort after the hardware has passed control back to the tcm_qla2xxx driver. Cc: Arun Easi <arun.easi@qlogic.com> Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: c0cb4496 ("qla2xxx: Add Host reset handling in target mode.") # v3.18. Signed-off-by:
-
Bart Van Assche authored
Implementations of the .write_pending() callback functions must guarantee that an appropriate LIO core callback function will be called immediately or at a later time. Make sure that this guarantee is met for aborted SCSI commands. [mkp: typo] Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: 694833ee ("scsi: tcm_qla2xxx: Do not allow aborted cmd to advance.") # v4.13. Fixes: a07100e0 ("qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM") # v4.5. Signed-off-by:
-
Bart Van Assche authored
The test "if (!cmd)" is not useful because it is guaranteed that cmd != NULL. Instead of testing the cmd pointer, rely on the tag to decide whether or not command allocation failed. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: 33e79977 ("qla2xxx: Add support for QFull throttling and Term Exchange retry") # v3.18. Signed-off-by:
-
Bart Van Assche authored
All qlt_send_term_imm_notif() callers pass '1' as second argument to this function. Hence remove the (broken) code that depends on that second argument having another value. Add a pr_debug() statement that prints rc to avoid that the compiler would complain that rc has been set but is not used. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
The current order for freeing memory is as follows: - struct crc_context itself. - struct crc_context member pointers. Change the freeing order into the following: - struct crc_context member pointers. - struct crc_context itself. Detected by Coverity. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: 50b81275 ("scsi: qla2xxx: Fix DMA error when the DIF sg buffer crosses 4GB boundary") # v5.1-rc1. Fixes: d7459527 ("scsi: qla2xxx: Add multiple queue pair functionality.") # v4.10. Signed-off-by:
-
Bart Van Assche authored
Make sure that the allocated interrupts are freed if allocating memory for the msix_entries array fails. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Clear each pointer after having freed memory such that it becomes safe to call qla2x00_mem_free() twice. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Instead of clearing all freed pointers at the end of qla2x00_mem_free(), clear freed pointers immediately after having freed the memory these pointers point at. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
This patch avoids that Coverity complains that qla2x00_async_event() writes outside the bounds of the mb[] arrays (MBA_IDC_AEN case). Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
It is important to know why a firmware command failed. Hence log 'rval' together with the values of the mailbox registers if a firwmare command fails. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
Bart Van Assche authored
Since Coverity cannot know that rport != NULL in qla2xxx_queuecommand() and since there is code in that function that dereferences the rport pointer, modify qla2xxx_queuecommand() such that it fails SCSI commands if rport == NULL. Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
