- 24 Apr, 2017 40 commits
-
-
yong mao authored
If we don't select a set of better parameters for our emmc host, It may easily occur CMD response CRC error. And also it may cause cannot boot up issue. Fot getting a set of better parameters, our emmc host supports data tune mechanism.Therefore, our emmc driver also should change to use data tune for CMD line. Because our emmc host use the different clock source to sample the CMD signal between HS200 and HS400 mode, the parameters are also different between these two modes. Separate cmd internal delay for HS200/HS400 mode. This change can fix "System can not boot up" issue. Signed-off-by:
Yong Mao <yong.mao@mediatek.com> Signed-off-by:
Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
yong mao authored
Add description for mediatek,hs200-cmd-int-delay Add description for mediatek,hs400-cmd-int-delay Add description for mediatek,hs400-cmd-resp-sel-rising Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Heiner Kallweit authored
Improve mmc_io_rw_extended a little: - using DIV_ROUND_UP achieves the same but is better readable - simplify code by using sg_set_buf - simplify one statement by using -= operator Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Chris Brandt authored
Signed-off-by:
Chris Brandt <chris.brandt@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Acked-by:
-
Masaharu Hayakawa authored
Current code gets number of taps only once and keeps the value. This is not correct, we need to obtain it every time before executing tuning, so remove the outer if-block. Signed-off-by:
Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com> [wsa: extracted from a larger patch and reworded commit message] Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by:
-
Wolfram Sang authored
In the (maybe academical) case, we don't get a DATAEND interrupt after DMA completed, we will wait endlessly for the completion to complete. This is not bad per se, since we have a more generic completion tracking a timeout. In that rare case, however, the DMA buffer will not get unmapped and we have a leak. Reorder the code, so unmapping will always take place. Signed-off-by:
-
Adrian Hunter authored
Move a function to avoid having to forward declare it in a subsequent patch. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ludovic Desroches <ludovic.desroches@microchip.com>
-
Adrian Hunter authored
Add runtime suspend/resume callbacks to match suspend/resume callbacks. Signed-off-by:
-
Adrian Hunter authored
The suspend / resume callbacks lack the flexibility to allow a device to specify a different function entirely. Change them around so that device functions are called directly and they in turn can call the default implementations if needed. Signed-off-by:
-
Adrian Hunter authored
It is confusing to have some parts of suspend / resume under conditional compilation and some parts not. Use conditional compilation everywhere. Signed-off-by:
-
Adrian Hunter authored
Do not use suspend/resume callbacks with runtime pm. It doesn't make sense and isn't being used, so remove. Signed-off-by:
-
Adrian Hunter authored
SDHCI provides more flexibility than simply calling sdhci_add_host(). Make that available by allowing devices to specify their own ->add_host() function. Signed-off-by:
-
Adrian Hunter authored
Add an interrupt hook and helper functions for enabling, disabling and delivering interrupts to a CQE. Signed-off-by:
-
Adrian Hunter authored
Factor out sdhci_set_default_irqs(). Signed-off-by:
-
Adrian Hunter authored
Add sdhci_cleanup_host() to cleanup __sdhci_add_host(). Signed-off-by:
-
Adrian Hunter authored
Get rid of unnecessary 'extern' in header file. Signed-off-by:
-
Adrian Hunter authored
Export sdhci_dumpregs so that it can be called by drivers. Signed-off-by:
-
Adrian Hunter authored
Ensure all prints start with the mmc host name, and the text all lines up. Signed-off-by:
-
Adrian Hunter authored
Use sdhci io wrappers consistently. Signed-off-by:
-
Adrian Hunter authored
Add response register to register dump. Signed-off-by:
-
Adrian Hunter authored
Ensure all debug prints start with the mmc host name. Signed-off-by:
-
Adrian Hunter authored
Tuning execution is already synchronized with respect to other host operations by upper layers "claiming" the host, which also takes care of runtime pm. There can be no requests in progress. Retain the spin lock usage only for ensuring that sending tuning commands is synchronized with respect to the interrupt handler. Signed-off-by:
-
Adrian Hunter authored
The spin lock is not necessary in set_ios. Anything that is racing with changes to the I/O state is already broken. The mmc core already provides synchronization via "claiming" the host. So remove spin_lock and friends from sdhci_set_ios and related callbacks. Signed-off-by:
-
Adrian Hunter authored
Drivers can use the host operation directly, so remove this now unused callback. Signed-off-by:
-
Adrian Hunter authored
Make use of an Intel ACPI _DSM that provides eMMC driver strength. Signed-off-by:
-
Adrian Hunter authored
Make use of an Intel ACPI _DSM that indicates if re-tuning is needed after D3. Signed-off-by:
-
Adrian Hunter authored
Let devices define their own private data to facilitate device-specific operations. The size of the private structure is specified in the sdhci_pci_fixes structure, then sdhci_pci_probe_slot() will allocate extra space for it, and sdhci_pci_priv() can be used to get a reference to it. Signed-off-by:
-
Adrian Hunter authored
Devices might save and restore tuning values so that re-tuning might not be needed after a pm transition. Let drivers decide by pushing the mmc_retune_needed() logic down to them. Signed-off-by:
-
Adrian Hunter authored
The delay loops for reset and clock enable always take at least 1 ms because they use mdelay(1). However they can take a lot less time e.g. less than 50us. Use ktime and reduce the delay to 10 microseconds per loop. Signed-off-by:
-
Eric Anholt authored
The 2835 has two SD controllers: The Arasan sdhci controller (supported by the iproc driver) and a custom sdhost controller. This patch adds a driver for the latter. The sdhci controller supports both sdcard and sdio. The sdhost controller supports the sdcard only, but has better performance. Also note that the rpi3 has sdio wifi, so driving the sdcard with the sdhost controller allows to use the sdhci controller for wifi support. The configuration is done by devicetree via pin muxing. Both SD controller are available on the same pins (2 pin groups = pin 22 to 27 + pin 48 to 53). So it's possible to use both SD controllers at the same time with different pin groups. The code was originally written by Phil Elwell in the downstream Rasbperry Pi tree. In preparation for the upstream merge it was cleaned up and the code base was moderized by Eric Anholt, Stefan Wahren and Gerd Hoffmann. Signed-off-by:
Eric Anholt <eric@anholt.net> Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Signed-off-by:
-
Eric Anholt authored
This is the other SD controller on the platform, which can be swapped to the role of SD card host using pin muxing. Signed-off-by:
-
tcharding authored
File contains multiple functions doing variations on the same thing, sdio_readb(), sdio_writeb()f, sdio_readw(), sdio_writew() etc. Although the functions have very similar logic the code is laid out in a variety of ways. This makes it overly complicated to read. There is a already a nice clean chunk of code, if we use this format for all instances then we will have cleaned up the code, reduced the line count and lessened the cognitive load required while reading. Less lines equals less bugs. Pick the most simple and clear code flow and change all functions to be the same. Signed-off-by:
Tobin C. Harding <me@tobin.cc> Signed-off-by:
-
tcharding authored
Various functions take as parameter an optional pointer. Pointer should be guarded with non-NULL check before dereferencing. Add non-NULL check before dereference of pointer. Signed-off-by:
-
Michał Zegan authored
This patch fixes the case where meson_mmc_probe function fails before core_clk is enabled. Originally, that would result in a try to disable the core clock, and if it was not already enabled, it would result in a kernel warning. This issue is similar to the one with div_clk. Fix it by introducing another error path used only between successfully enabling the core clock, and successfully enabling the div clock. That would ensure that core clock is disabled only if it was enabled before. Signed-off-by:
Michał Zegan <webczat@webczatnet.pl> Signed-off-by:
-
Thierry Reding authored
The SDHCI controller found on Tegra186 in very similar to the controller found on earlier generations of Tegra. Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Thierry Reding authored
The list of compatible strings is somewhat difficult to read and extend. Reformat it into a list to make it more easily extensible. While at it, also remove the "plus one of the above" clause because it isn't actually valid. Signed-off-by:
-
Jisheng Zhang authored
sdhci_pltfm_init() has already set the platform drvdata for us, remove the unnecessary platform_set_drvdata() call. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Acked-by:
Patrice Chotard <patrice.chotard@st.com> Signed-off-by:
-
Jisheng Zhang authored
sdhci_pltfm_init() has already set the platform drvdata for us, remove the unnecessary platform_set_drvdata() call. Signed-off-by:
-
Jisheng Zhang authored
sdhci_pltfm_init() has already set the platform drvdata for us, remove the unnecessary platform_set_drvdata() call. Signed-off-by:
-
Piotr Sroka authored
Add support for HS400ES mode to Cadence SDHCI driver. Signed-off-by:
Piotr Sroka <piotrs@cadence.com> Reviewed-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
