- 27 Jun, 2013 11 commits
-
-
Khalid Aziz authored
I ported BusLogic driver to 64-bit. There is no current maintainer for this driver and since I made significant changes to the driver for 64-bit porting work, I will continue to maintain it. Signed-off-by:
Khalid Aziz <khalid@gonehiking.org> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Khalid Aziz authored
[jejb: fix up pointer to int cast warning] Signed-off-by:
Khalid Aziz <khalid.aziz@oracle.com> Signed-off-by:
-
Khalid Aziz authored
Fix CamelCase and extra long lines in the buslogic driver. Signed-off-by:
-
Eddie Wai authored
This is the kernel part of the modification to extract the net params from the ibft sysfs to the iface struct used for the connection request upon sync_session in the open-iscsi util. Three new session sysfs params are defined: boot_root - holds the name of the /sys/firmware/ibft or iscsi_rootN boot_nic - holds the ethernetN name boot_target - holds the targetN name Signed-off-by:
Eddie Wai <eddie.wai@broadcom.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Mahesh Rajashekhara authored
One of the customer had reported that the set of raid logical arrays will become unavailable (I/O offline) after a long hours of IO stress test. The OS wouldn`t be accessible afterwards and require a hard reset. This driver patch has a fix for race condition between the doorbell and the circular buffer. The driver is modified to do an extra read after clearing the doorbell in case there had been a completion posted during the small timing window. With this fix, we ran IO stress for ~13 days. There were no IO failures. Signed-off-by:
Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
wenxiong@linux.vnet.ibm.com authored
Signed-off-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Martin K. Petersen authored
SATA drives located behind a SAS controller would incorrectly receive WRITE SAME commands. Tweak the heuristics so that: - If REPORT SUPPORTED OPERATION CODES is provided we will use that to choose between WRITE SAME(16), WRITE SAME(10) and disabled. This also fixes an issue with the old code which would issue WRITE SAME(10) despite the command not being whitelisted in REPORT SUPPORTED OPERATION CODES. - If REPORT SUPPORTED OPERATION CODES is not provided we will fall back to WRITE SAME(10) unless the device has an ATA Information VPD page. The assumption is that a SATL which is smart enough to implement WRITE SAME would also provide REPORT SUPPORTED OPERATION CODES. To facilitate the new heuristics scsi_report_opcode() has been modified to so we can distinguish between "operation not supported" and "RSOC not supported". Reported-by:
H. Peter Anvin <hpa@zytor.com> Tested-by:
Bernd Schubert <bernd.schubert@itwm.fraunhofer.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dan Carpenter authored
There is an unlock missing if the == FNIC_IOREQ_ABTS_PENDING is false. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Hiral Patel <hiralpat@cisco.com> Signed-off-by:
-
Vijaya Mohan Guvva authored
Update bfa driver version to 3.2.21.1 Update bfa to use firmware image versions 3.2.1.0 Signed-off-by:
Vijaya Mohan Guvva <vmohan@brocade.com> Signed-off-by:
-
Vijaya Mohan Guvva authored
Disassoicate path_tov in the driver with the dev_loss_tmo set by the application. Signed-off-by:
-
Vijaya Mohan Guvva authored
This patch enables support for chinook quad port 16G FC card (falcon) Signed-off-by:
-
- 26 Jun, 2013 29 commits
-
-
Vijaya Mohan Guvva authored
Fix endianess issue on Big-endian architecture for firmware statistics Signed-off-by:
-
Vijaya Mohan Guvva authored
Fix bug_on condition check in RPSC (Report Port Speed Capabilities) response processing. Signed-off-by:
-
Vijaya Mohan Guvva authored
Allow processing completions from firmware during IOC_DISABLE request is being processed by the firmware, by setting the queue_process flag appropriately. Signed-off-by:
-
Vijaya Mohan Guvva authored
Get RDS drop interrupts and REC (Read Exchange Concise) related stats from firmware. Signed-off-by:
-
Vijaya Mohan Guvva authored
1. While FRU VPD data update, inform firmware to send a completion event on I2C bus. Without this change, firmware used to send completion message on I2C bus for every chunk of FRU VPD update. 2. Support for FRU VPN update on CHINOOK2 cards. 3. Append port count to the model name to differentiate between single port and dual port model of 1860. 4. Update the size of the model name to 16bytes Signed-off-by:
-
Vijaya Mohan Guvva authored
Replaced usage of void * with u64 in data structure shared between brocade user space libraries and the bfa driver to address pointer size changes across 32-bit vs 64-bit to have the compatibility between 32bit library and 64bit driver and vice versa. Signed-off-by:
-
Vijaya Mohan Guvva authored
Root cause: When kernel crashes, On brocade 815/825 adapters, bfa IOC state machine and FW doesn't get a notification and hence are not cleanly shutdown. So registers holding driver/IOC state information are not reset back to valid disabled/parking values. This causes subsequent driver initialization to fail during kdump kernel boot. Fix description: during the initialization of first PCI function, reset corresponding register when unclean shutown is detect by reading chip registers. This will make sure that ioc/fw gets clean re-initialization. Signed-off-by:
-
Vijaya Mohan Guvva authored
Retry FDISC a max of 6 times. Introduce new events to handle vport login fails due to max logins to fabric/switch. Signed-off-by:
Anil Gurumurthy <agurumur@brocade.com> Signed-off-by:
-
Vijaya Mohan Guvva authored
On Xen kernels, if ATC (address translation cache) is enabled, the first PCIe DMA read from the adapter fails with an error. This is due to a bug ASIC, which leads to a failure of 1860 ports to be initialised. This patch includes the fix to disable Invalidated Tag Match Enable capability by setting the bit 26 of CHIP_MISC_PRG to 0, by default it is set to 1. Signed-off-by:
-
Vijaya Mohan Guvva authored
Update addl. fields in FDMI to confirm to FC-GS6 standard for RPA and RHBA commands. Signed-off-by:
-
Vijaya Mohan Guvva authored
The WARN_ON condition check in IO completion path is wrong. IOtags returned by the firmware is compared with driver/bfa iotag after masking the retry count bits. Signed-off-by:
-
Vijaya Mohan Guvva authored
D-Port is a new port type created with the intention of running link level diagnostic tests like loopback, traffic test. In static D-port mode, user configures the port to D-port mode and starts the test, but in dynamic D-port, once the Brocade switch port is configured to D-port, it will reject the regular FLOGI from HBA with reason that it is in D-port mode. So based on the reason code HBA port will turn itself into D-port and start diagnostic test. Signed-off-by:
Sudarsana Reddy Kalluru <skalluru@brocade.com> Signed-off-by:
-
Vijaya Mohan Guvva authored
This patch includes changes to get FC HBA feature Forward Error Correction (FEC) (enabled at 16Gig speed) status from firmware and to return to brocade HBA management utility. Signed-off-by:
-
Vijaya Mohan Guvva authored
This patch includes changes to 1) Enable/disable fc credit recovery on Brocade FC adapter port operating at max supported speed. 2) Get credit recovery status and stats related to credit loss and recovered credits Signed-off-by:
-
Sergei Shtylyov authored
The 'ctl' field of the 'struct ata_taskfile' is not really dual purpose, i.e. it is not intended for storing the alternate status register (which is mapped at the same address in the legacy IDE controllers) in the qc_fill_rtf() method. No other 'libata' driver except 'drivers/scsi/ipr.c' stores the alternate status register's value in the 'ctl' field of 'qc->result_tf', hence this driver should not do this as well... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by:
-
James Smart authored
Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
