This adds basic SPI nodes to the base rk3288 device tree file.

A few notes:
* It's assumed that most users of the SPI ports are using chip select
  0.  Thus the default pinctrl for the ports enables chip select 0
  (but not chip select 1 on ports that have it).  If a board wants to
  use chip select 1 or wants a GPIO chip select the board should
  override the pinctrl (just like boards can override UART pinctrl if
  they have hardware flow control).
* Since SPI DMA support appears broken and the SPI works fine without
  DMA we don't include the DMA references.  That can come in a later
  change.
Signed-off-by: huang lin <hl@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

USB host1 port is the host A port nearby the otg port.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

rk3288 has two kind of usb controller, this add the dwc2 controller
for otg and host1.

Controller can works with usb PHY default setting and Vbus on.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch requires that <https://patchwork.kernel.org/patch/4701721/>
land in order to compile.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the core device nodes for the SARADC found on both the Cortex-A9 series
(rk3066 and rk3188) as well as the newer rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The Radxa Rock uses a hym8563 as rtc. Add the i2c device and necessary
pinconfig for the interrupt pin - labeled rtc_int in the schematics.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

PWM0 is the PWM associated with the LCD backlight.  Enable it.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds the PWM info (other than the VOP PWM) to the main rk3288
dtsi file.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The PMIC interrupt pinctrl line was added to the rk3288-evb-act8846,
but it's the same line on both the ACT8846 version and the RK808
version.  This makes a lot of sense since they share the same SoC
daugherboard.  Move the pinctrl definition to the common file so we
can use it for the RK808 version.

NOTE: The PMIC interrupt doesn't _actually_ go to the PMIC on the
ACT8846 version of the board (it does on the RK808), but our
convention is to label things as they're labelled on the schematics.
In the very least you can argue that this is the interrupt from the
PMIC daughtercard even if it doesn't actually go to the PMIC chip.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This enables basic SD and eMMC support.  Things are not yet running at
the fastest speed and we don't have the regulators specified, but we
can at least use the eMMC and SD cards now.

A note:
* Though MMC DDR50 mode is partially supported in the dw_mmc
  rk3288-specific code in Addy's patch, Addy's patch doesn't add
  tuning support.  That means DDR50 mode is not reliable.  From the
  3288 TRM: "Tuning is required for other speed modes-such as
  DDR50-even though the output delay from the card is less than one
  cycle."  Thus, we don't enable MMC DDR50 mode in this patch.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds support for the sdmmc and emmc ports on the rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Pull x86 platform driver updates from Matthew Garrett:
 "A moderate number of changes, but nothing awfully significant.

  A lot of const cleanups, some reworking and additions to the rfkill
  quirks in the asus driver, a new driver for generating falling laptop
  events on Toshibas and some misc fixes.

  Maybe vendors have stopped inventing things"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (41 commits)
  platform/x86: Enable build support for toshiba_haps
  Documentation: Add file about toshiba_haps module
  platform/x86: Toshiba HDD Active Protection Sensor
  asus-nb-wmi: Add wapf4 quirk for the U32U
  alienware-wmi: make hdmi_mux enabled on case-by-case basis
  ideapad-laptop: Constify DMI table and other r/o variables
  asus-nb-wmi.c: Rename x401u quirk to wapf4
  compal-laptop: correct invalid hwmon name
  toshiba_acpi: Add Qosmio X75-A to the alt keymap dmi list
  toshiba_acpi: Add extra check to backlight code
  Fix log message about future removal of interface
  ideapad-laptop: Disable touchpad interface on Yoga models
  asus-nb-wmi: Add wapf4 quirk for the X550CC
  intel_ips: Make ips_mcp_limits variables static
  thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
  fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
  hp-wmi: Add missing __init annotations to initialization code
  hp_accel: Constify ACPI and DMI tables
  fujitsu-tablet: Mark DMI callbacks as __init code
  dell-laptop: Mark dell_quirks[] DMI table as __initconst
  ...

Pull idle update from Len Brown:
 "Two Intel-platform-specific updates to intel_idle, and a cosmetic
  tweak to the turbostat utility"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: tweak whitespace in output format
  intel_idle: Broadwell support
  intel_idle: Disable Baytrail Core and Module C6 auto-demotion

Pull module fix from Rusty Russell:
 "Nasty potential bug if someone uses a known module param with an
  invalid value (we don't fail unknown module params any more, just
  warn)"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  module: Clean up ro/nx after early module load failures

Pull virtio-rng update from Amit Shah:
 "Add derating factor for use by hwrng core

  Sending directly to you with the commit log changes Ted Ts'o pointed
  out.  Not sure if Rusty's back after his travel, but this already has
  his s-o-b"

* 'rng-queue' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio:
  virtio: rng: add derating factor for use by hwrng core

Pull btrfs updates from Chris Mason:
 "These are all fixes I'd like to get out to a broader audience.

  The biggest of the bunch is Mark's quota fix, which is also in the
  SUSE kernel, and makes our subvolume quotas dramatically more
  accurate.

  I've been running xfstests with these against your current git
  overnight, but I'm queueing up longer tests as well"

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: disable strict file flushes for renames and truncates
  Btrfs: fix csum tree corruption, duplicate and outdated checksums
  Btrfs: Fix memory corruption by ulist_add_merge() on 32bit arch
  Btrfs: fix compressed write corruption on enospc
  btrfs: correctly handle return from ulist_add
  btrfs: qgroup: account shared subtrees during snapshot delete
  Btrfs: read lock extent buffer while walking backrefs
  Btrfs: __btrfs_mod_ref should always use no_quota
  btrfs: adjust statfs calculations according to raid profiles

Pull file locking bugfixes from Jeff Layton:
 "Most of these patches are to fix a long-standing regression that crept
  in when the BKL was removed from the file-locking code.  The code was
  converted to use a conventional spinlock, but some fl_release_private
  ops can block and you can end up sleeping inside the lock.

  There's also a patch to make /proc/locks show delegations as 'DELEG'"

* tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux:
  locks: update Locking documentation to clarify fl_release_private behavior
  locks: move locks_free_lock calls in do_fcntl_add_lease outside spinlock
  locks: defer freeing locks in locks_delete_lock until after i_lock has been dropped
  locks: don't reuse file_lock in __posix_lock_file
  locks: don't call locks_release_private from locks_copy_lock
  locks: show delegations as "DELEG" in /proc/locks

Pull aio updates from Ben LaHaise.

* git://git.kvack.org/~bcrl/aio-next:
  aio: use iovec array rather than the single one
  aio: fix some comments
  aio: use the macro rather than the inline magic number
  aio: remove the needless registration of ring file's private_data
  aio: remove no longer needed preempt_disable()
  aio: kill the misleading rcu read locks in ioctx_add_table() and kill_ioctx()
  aio: change exit_aio() to load mm->ioctx_table once and avoid rcu_read_lock()

Makefile and Kconfig build support patch for the newly introduced
kernel module toshiba_haps.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

This patch provides information about the Toshiba HDD
Active Protection Sensor driver module toshiba_haps.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

This driver adds support for the built-in accelereometer found
on recent Toshiba laptops with HID TOS620A.

This driver receives ACPI notify events 0x80 when the sensor
detects a sudden move or a harsh vibration, as well as an
ACPI notify event 0x81 whenever the movement or vibration has
been stabilized.

Also provides sysfs entries to get/set the desired protection
level and reseting the HDD protection interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

As reported here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1173681
the U32U needs wapf=4 too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Not all HW supporting WMAX method will support the HDMI mux feature.
Explicitly quirk the HW that does support it.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Constify the rfkill_blacklist[] DMI table, the ideapad_rfk_data[] table
and the ideapad_attribute_group attribute group. There's no need to have
them writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

The actual x401u does not use the so named x401u quirk but the x55u quirk.
All that the x401u quirk does it setting wapf to 4, so rename it to wapf4 to
stop the confusion.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Change the name of the hwmon interface from "compal-laptop" to "compal".
A dash is an invalid character for a hwmon name and caused the call to
hwmon_device_register_with_groups() to fail.
Signed-off-by: Roald Frederickx <roald.frederickx@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

The Toshiba Qosmio X75-A series models also come with
the new keymap layout.

This patch adds this model to the alt_keymap_dmi list,
along with an extra key found on these models.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Some Toshiba models (most notably Qosmios) come with an
incomplete backlight method where the AML code doesn't
check for write or read commands and always returns
HCI_SUCCESS and the actual brightness (and in some
cases the max brightness), thus allowing the backlight
interface to be registered without write support.

This patch changes the set_lcd_brightness function,
checking the returned values for values greater than
zero to avoid registering a broken backlight interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

If this is going away, it won't be in 2012.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Yoga models don't offer touchpad ctrl through the ideapad interface, causing
ideapad_sync_touchpad_state to send wrong touchpad enable/disable events.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

As reported here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1173681
the X550CC needs wapf=4 too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

These variables don't need to be visible outside of this compilation
unit, make them static.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Mark volume_alsa_control_vol and volume_alsa_control_mute as __initdata,
as snd_ctl_new1() will copy the relevant parts, so there is no need to
keep the master copies around after initialization.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

The DMI table is only ever used during initialization. Mark it as
__initconst so its memory can be released afterwards -- roughly 1.5 kB.
In turn, the callback functions can be marked with __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

These functions are only called from other initialization routines, so
can be marked __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

Constify the lis3lv02d_device_ids[] ACPI and the lis3lv02d_dmi_ids[] DMI
tables. There's no need to have them writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

The DMI table is already marked as __initconst, so can be the callback
functions as they're only used in that context.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Robert Gerlach <khnz@gmx.de>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

The dell_quirks[] DMI table is only ever used during initialization.
Mark it as __initconst so its memory can be released afterwards --
roughly 5.7 kB. In turn, the callback function can be marked with
__init, too.

Also the touchpad_led_init() function can be marked __init as it's only
referenced from dell_init() -- an __init function.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>