Errors that cannot be cleared (determined by reading REGERR register)
are currently handled by masking it. Documentation states that REGERR
"Checks which application/debug error sources are active" - it does not
indicate that this is "interrupt status" - masked out status represented
eventually in the irq line to MPU.
For example:

Lets say module 0 bit 8(0x100) was unclearable, we do the mask it from
generating further errors. However in the following cases:
a) bit 9 of Module 0
OR
b) any bit of Module 1+
occur, the interrupt handler wrongly assumes that the raw interrupt
status of module 0 bit 8 is the root cause of the interrupt, and
returns. This causes unhandled interrupt and resultant infinite
interrupts.

Fix this scenario by storing the events we masked out and masking raw
status with masked ones before identifying and handling the error.
Reported-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Current interrupt handler does the first level parse to identify the
slave and then handles the slave even identification, reporting and
clearing of event as well. It is hence logical to split the handler
into two where the primary handler just parses the flagmux till it
identifies a slave and the slave handling, reporting and clearing is
done in a helper function.

While at it update the documentation in kerneldoc style.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

The logic between handling CUSTOM_ERROR and STANDARD_ERROR is just the
reporting style.

So make it generic, simplify and standardize the reporting with both
master and target information printed to log.

Handle the register address difference for master code for standard
error and custom error as well.

While at it, fix a minor indentation error.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

As per Documentation (OMAP4+), then masterid is infact encoded as
follows:
"L3_TARG_STDERRLOG_MSTADDR[7:0] STDERRLOG_MSTADDR stores the NTTP
master address. The master address is the concatenation of Prefix &
Initiator ConnID. It is defined on 8 bits. The 6 MSBs are used to
distinguish the different initiators."

So, when we matchup currently with the master ID list, we never get a
proper match other than when MPU is the master (thanks to 0).

Now, on other platforms such as AM437x, this tends to be bits[5:0].

Fix this by using the relevant 6MSBits to identify the master ID for
standard and custom errors.
Reported-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

This allows us to encompass target information and flag mux offset that
points to the target information into a singular structure. This saves
us the need to look up two different arrays indexed by module ID for
information.

This allows us to reduce the static target information allocation to
just the ones that are documented.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

DRA7xx SoC has the same l3-noc interconnect ip (as OMAP4 and OMAP5), but
AM437x SoC has just 2 modules instead of 3 which other SoCs have.

So, stop using direct access of array indices and use of->match data and
simplify implementation to benefit future usage.

While at it, rename a few very generic variables to make them omap
specific. This helps us differentiate from DRA7 and AM43xx data in the
future.

NOTE: None of the platforms that use omap_l3_noc are non-device tree
anymore. So, it is safe to assume OF match here.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: split, refactor and optimize logic]
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

On DRA7, unlike on OMAP4 and OMAP5, the flag mux input numbers used
to indicate the source of errors are not continous. Have a way in the
driver to catch these and WARN the user of the flag mux input thats
either undocumented or wrong.

In the similar vein, Timeout errors in AM43x can't be cleared per h/w
team, neither does it have a STDERRLOG_MAIN to clear the error.

Further, the mux bit offset might not even be indexed into our array
of known mux input description, in which case we'd have a abort.

So, define a static range check for bit description and any definition
which has target_name set to NULL (the ones that are not populated or
ones that are specifically marked in the case of discontinous input
numbers), can handle the same gracefully. Upon occurance of error from
such sources, mask it. Otherwise, we'd have an infinite interrupt
source without any means to clear it.

NOTE: follow on patch ensures that these masked bits are ignored.

[nm@ti.com: rebase, squash and improve]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Currently the target instance information is organized indexed by bit
field offset into multiple arrays.

1. We currently have offsets specific to each target associated with each
clock domains are in seperate arrays:

l3_targ_inst_clk1
l3_targ_inst_clk2
l3_targ_inst_clk3

2. Then they are organized per master index in l3_targ.

3. We have names in l3_targ_inst_name as an array to array of strings
corresponding to the above with offsets.

Simplify the same by defining a structure for information containing
both target offset and name. this is then stored in arrays per domain
and organized into an array indexed off domain.

The array is still indexed based on bit field offset.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Move the L3 master structure out of the static definition to enable
reuse for other SoCs.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

just simplify derefencing that is equivalent.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Currently we use __raw_readl and writel in this driver. Considering
there is no specific need for a memory barrier, replacing writel
with endian-neutral writel_relaxed and replacing __raw_readls with
the corresponding endian-neutral readl_relaxed allows us to have a
standard set of register operations for the driver.

While at it, simplify address computation using variables for
register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

l3->dev is not populated, so populate it and use it to print information
relevant to the device instead of using a generic pr_*.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

we do not use iclk directly anymore. And, even if we had to, we
should be using pm_runtime APIs to do the same to be completely SoC
independent.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Since omap_l3_noc driver is now being used for OMAP5 and reusable with
DRA7 and AM437x, using omap4 specific naming is misleading.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

This is an embarrassing patch :(.

Texas Corporation does not make OMAP. Texas Instruments Inc does.

For that matter I dont seem to be able to find a Texas Corporation on
the internet either.

While at it, update coverage to the current year and update the template
to remove redundant information and use the standard boiler plate
licensing.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Use dev_err() which will going to print the driver's name as well and the
KERN_ERR level is sufficient in this case (we also print via dev_err when
there is an error with the mem resources)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

It is NOP after the devm_* conversion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

With this we can remove the free_irq() calls from probe and remove.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

We can then remove the iounmap() calls from probe and remove.
Since the driver requests the resources via index we can do the mem resource
request within a for loop.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

We can remove the kfree() calls from probe and remove.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

Pull vfs fixes from Al Viro:
 "Switch mnt_hash to hlist, turning the races between __lookup_mnt() and
  hash modifications into false negatives from __lookup_mnt() (instead
  of hangs)"

On the false negatives from __lookup_mnt():
 "The *only* thing we care about is not getting stuck in __lookup_mnt().
  If it misses an entry because something in front of it just got moved
  around, etc, we are fine.  We'll notice that mount_lock mismatch and
  that'll be it"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  switch mnt_hash to hlist
  don't bother with propagate_mnt() unless the target is shared
  keep shadowed vfsmounts together
  resizable namespace.c hashes

I am the new kernel tree Documentation maintainer (except for parts that
are handled by other people, of course).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull input updates from Dmitry Torokhov:
 "Some more updates for the input subsystem.

  You will get a fix for race in mousedev that has been causing quite a
  few oopses lately and a small fixup for force feedback support in
  evdev"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: mousedev - fix race when creating mixed device
  Input: don't modify the id of ioctl-provided ff effect on upload failure

It its possible to configure your PAM stack to refuse login if audit
messages (about the login) were unable to be sent.  This is common in
many distros and thus normal configuration of many containers.  The PAM
modules determine if audit is enabled/disabled in the kernel based on
the return value from sending an audit message on the netlink socket.
If userspace gets back ECONNREFUSED it believes audit is disabled in the
kernel.  If it gets any other error else it refuses to let the login
proceed.

Just about ever since the introduction of namespaces the kernel audit
subsystem has returned EPERM if the task sending a message was not in
the init user or pid namespace.  So many forms of containers have never
worked if audit was enabled in the kernel.

BUT if the container was not in net_init then the kernel network code
would send ECONNREFUSED (instead of the audit code sending EPERM).  Thus
by pure accident/dumb luck/bug if an admin configured the PAM stack to
reject all logins that didn't talk to audit, but then ran the login
untility in the non-init_net namespace, it would work!! Clearly this was
a bug, but it is a bug some people expected.

With the introduction of network namespace support in 3.14-rc1 the two
bugs stopped cancelling each other out.  Now, containers in the
non-init_net namespace refused to let users log in (just like PAM was
configfured!) Obviously some people were not happy that what used to let
users log in, now didn't!

This fix is kinda hacky.  We return ECONNREFUSED for all non-init
relevant namespaces.  That means that not only will the old broken
non-init_net setups continue to work, now the broken non-init_pid or
non-init_user setups will 'work'.  They don't really work, since audit
isn't logging things.  But it's what most users want.

In 3.15 we should have patches to support not only the non-init_net
(3.14) namespace but also the non-init_pid and non-init_user namespace.
So all will be right in the world.  This just opens the doors wide open
on 3.14 and hopefully makes users happy, if not the audit system...
Reported-by: Andre Tomt <andre@tomt.net>
Reported-by: Adam Richter <adam_richter2004@yahoo.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use cmpxchg() to atomically set i_flags instead of clearing out the
S_IMMUTABLE, S_APPEND, etc. flags and then setting them from the
EXT4_IMMUTABLE_FL, EXT4_APPEND_FL flags, since this opens up a race
where an immutable file has the immutable flag cleared for a brief
window of time.
Reported-by: John Sullivan <jsrhbz@kanargh.force9.co.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fixes RCU bug - walking through hlist is safe in face of element moves,
since it's self-terminating.  Cyclic lists are not - if we end up jumping
to another hash chain, we'll loop infinitely without ever hitting the
original list head.

[fix for dumb braino folded]

Spotted by: Max Kellermann <mk@cm4all.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

If the dest_mnt is not shared, propagate_mnt() does nothing -
there's no mounts to propagate to and thus no copies to create.
Might as well don't bother calling it in that case.

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

preparation to switching mnt_hash to hlist

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* switch allocation to alloc_large_system_hash()
* make sizes overridable by boot parameters (mhash_entries=, mphash_entries=)
* switch mountpoint_hashtable from list_head to hlist_head

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull timer fix from Ingo Molnar:
 "A late breaking fix from John.  (The bug fixed has a hard lockup
  potential, but that was not observed, warnings were)"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Revert to calling clock_was_set_delayed() while in irq context

Pull Ceph fix from Sage Weil:
 "This drops a bad assert that a few users have been hitting but we've
  only recently been able to track down"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: drop an unsafe assertion

We should not be using static variable mousedev_mix in methods that can be
called before that singleton gets assigned. While at it let's add open and
close methods to mousedev structure so that we do not need to test if we
are dealing with multiplexor or normal device and simply call appropriate
method directly.

This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=71551Reported-by: GiulioDP <depasquale.giulio@gmail.com>
Tested-by: GiulioDP <depasquale.giulio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If a new (id == -1) ff effect was uploaded from userspace,
ff-core.c::input_ff_upload() will have assigned a positive number to the
new effect id.  Currently, evdev.c::evdev_do_ioctl() will save this new id
to userspace, regardless of whether the upload succeeded or not.

On upload failure, this can be confusing because the dev->ff->effects[]
array will not contain an element at the index of that new effect id.

This patch fixes this by leaving the id unchanged after upload fails.

Note: Unfortunately applications should still expect changed effect id for
quite some time.

This has been discussed on:
http://www.mail-archive.com/linux-input@vger.kernel.org/msg08513.html
("ff-core effect id handling in case of a failed effect upload")
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Olivier Bonvalet reported having repeated crashes due to a failed
assertion he was hitting in rbd_img_obj_callback():

    Assertion failure in rbd_img_obj_callback() at line 2165:
	rbd_assert(which >= img_request->next_completion);

With a lot of help from Olivier with reproducing the problem
we were able to determine the object and image requests had
already been completed (and often freed) at the point the
assertion failed.

There was a great deal of discussion on the ceph-devel mailing list
about this.  The problem only arose when there were two (or more)
object requests in an image request, and the problem was always
seen when the second request was being completed.

The problem is due to a race in the window between setting the
"done" flag on an object request and checking the image request's
next completion value.  When the first object request completes, it
checks to see if its successor request is marked "done", and if
so, that request is also completed.  In the process, the image
request's next_completion value is updated to reflect that both
the first and second requests are completed.  By the time the
second request is able to check the next_completion value, it
has been set to a value *greater* than its own "which" value,
which caused an assertion to fail.

Fix this problem by skipping over any completion processing
unless the completing object request is the next one expected.
Test only for inequality (not >=), and eliminate the bad
assertion.
Tested-by: Olivier Bonvalet <ob@daevel.fr>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>

Pull networking fixes from David Miller:

 1) We've discovered a common error in several networking drivers, they
    put VLAN offload features into ->vlan_features, which would suggest
    that they support offloading 2 or more levels of VLAN encapsulation.
    Not only do these devices not do that, but we don't have the
    infrastructure yet to handle that at all.

    Fixes from Vlad Yasevich.

 2) Fix tcpdump crash with bridging and vlans, also from Vlad.

 3) Some MAINTAINERS updates for random32 and bonding.

 4) Fix late reseeds of prandom generator, from Sasha Levin.

 5) Bridge doesn't handle stacked vlans properly, fix from Toshiaki
    Makita.

 6) Fix deadlock in openvswitch, from Flavio Leitner.

 7) get_timewait4_sock() doesn't report delay times correctly, fix from
    Eric Dumazet.

 8) Duplicate address detection and addrconf verification need to run in
    contexts where RTNL can be obtained.  Move them to run from a
    workqueue.  From Hannes Frederic Sowa.

 9) Fix route refcount leaking in ip tunnels, from Pravin B Shelar.

10) Don't return -EINTR from non-blocking recvmsg() on AF_UNIX sockets,
    from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
  vlan: Warn the user if lowerdev has bad vlan features.
  veth: Turn off vlan rx acceleration in vlan_features
  ifb: Remove vlan acceleration from vlan_features
  qlge: Do not propaged vlan tag offloads to vlans
  bridge: Fix crash with vlan filtering and tcpdump
  net: Account for all vlan headers in skb_mac_gso_segment
  MAINTAINERS: bonding: change email address
  MAINTAINERS: bonding: change email address
  ipv6: move DAD and addrconf_verify processing to workqueue
  tcp: fix get_timewait4_sock() delay computation on 64bit
  openvswitch: fix a possible deadlock and lockdep warning
  bridge: Fix handling stacked vlan tags
  bridge: Fix inabillity to retrieve vlan tags when tx offload is disabled
  vhost: validate vhost_get_vq_desc return value
  vhost: fix total length when packets are too short
  random32: avoid attempt to late reseed if in the middle of seeding
  random32: assign to network folks in MAINTAINERS
  net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset
  core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors
  vlan: Set hard_header_len according to available acceleration
  ...

Vlad Yasevich says:

====================
Audit all drivers for correct vlan_features.

Some drivers set vlan acceleration features in vlan_features.  This causes
issues with Q-in-Q/802.1ad configurations.

Audit all the drivers for correct vlan_features.  Fix broken ones.
Add a warning to vlan code to help catch future offenders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For completeness, turn off vlan rx acceleration in vlan_features so
that it doesn't show up on q-in-q setups.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not include vlan acceleration features in vlan_features as that
precludes correct Q-in-Q operation.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>