This patch reimplements functions calculating minimum and maximum clock
rates to leverage clock rate cache introduced by previous patches.

In addition, the calculation is simplified to just comparing input
clock rates (max case) or input clock rates divided by maximum divisor
(min case), which is basically what the original code did, but with much
more unnecessary work.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

IS_ERR() must be used to make sure that not a valid clock was returned
by clk_get() and company.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

To fix scheduling while atomic happening in sdhci_s3c_set_clock() caused
by calling clk_get_rate() that might sleep, this patch modifies the
driver to cache rates of all bus clocks at probe time and then only use
those cache values.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Current implementation of sdhci_s3c_consider_clock() is highly
inefficient due to multiple integer divisions by variable performed in a
loop. Since only divisors that are powers of two are considered, this
patch replaces them with respective shifts, removing all the integer
divisions.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by; Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Introduce "altr,socfpga-dw-mshc" to enable Altera's SOCFPGA platform
specific implementation of the dw_mmc driver.

Also add the "syscon" binding to the "altr,sys-mgr" node. The clock
driver can use the syscon driver to toggle the register for the SD/MMC
clock phase shift settings.

Finally, fix an indentation error for the sysmgr node.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Chris Ball <chris@printf.net>

Like the rockchip, Altera's SOCFPGA platform specific implementation of the
dw_mmc driver requires using the HOLD register for SD commands. This patch
renames dw_mci_rockchip_prepare_command to dw_mci_pltfm_prepare_command so
that SOCFPGA and Rockchip can use it.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

It turns now that the only really platform specific code that is needed for
SOCFPGA is using the SDMMC_CMD_USE_HOLD_REG in the prepare_command function.
Since the Rockchip already has this functionality, re-use the code that is
already in dw_mmc-pltfm.c.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

If mrq->sbc is not NULL but data->stop happens to be NULL,
it will lead to NULL pointer dereferencing. Avoid this by
having a NULL check for data->stop.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Commit c02cecb9 ("ARM: orion: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Commit 1ef21f63 ("ARM: msm: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Commit 0976f16d ("mmc: dw_mmc: add support tuning scheme") introduced
the execute_tuning hook but did not add its description for kernel docs.
Update the same.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

pdata could be NULL if cd_gpio = -1. Dereference pdata only
if it is not NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

'of_id' is dereferenced before NULL pointer check. Move it to
after the check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <chris@printf.net>

sizeof should be of the parent structure type.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Enable the external clock needed by the host controller during the
probe and disable it during the remove.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

The ux500 variants have HW busy detection support, which is indicated
by the busy_detect flag. For these variants let's enable the
MMC_CAP_WAIT_WHILE_BUSY flag and add the support for it.

The mmc core will provide the RSP_BUSY command flag for those requests
we should care about busy detection. Regarding the max_busy_timeout,
the HW don't support busy detection timeouts so at this initial step
let's make it simple and set it to zero to indicate we are able to
support any timeout.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

In case of a read operation both MCI_CMDRESPEND and MCI_DATAEND can be
set in the status register when entering the interrupt handler. This is
due to that the card start sending data before the host has
acknowledged the command response.

To resolve the issue for this scenario, we must start by handling the
CMD irq instead of the DATA irq. The reason is beacuse the completion
of the DATA irq will not respect the current command and then causing
it to be garbled.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

When sending a stop command at the recovery path, use a R1B response
when the failing data request are a WRITE. Thus we also care about the
busy detection completion in this case.

For a failing READ request, we use a R1 response for the stop command,
since we don't need to care about busy detection in this case.

To align behavior between hosts supporting MMC_CAP_WAIT_WHILE_BUSY and
those who are not, we add a CMD13 polling method for the card's status.

We also respect whether the host has specified the max_busy_timeout,
which means we may fallback to CMD13 polling if the timeout is greater
than what the host are able to support.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Currently for write request we don't trust the hw busy detection to be
fully handled by host, thus we also poll the card's status until we see
it's gets out of the busy state.

Still there are scenarios where it will a benefit to trust the hw busy
detection done by the host, since no additional polling is needed.
Let's prepare card_busy_detect() to be able to handle this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

To complete a data write request we poll for the card's status register
by sending CMD13. The are other scenarios when this polling method are
needed, which is why we here moves this code to it's own function. No
functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

While using open ended transmission and thus ending the transfer by
sending a stop command, we shall use R1B only for writes and R1 shall
be used for reads. Previously R1B were used in both cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

When sending the sleep command for host drivers supporting
MMC_CAP_WAIT_WHILE_BUSY, we need to confirm that max_busy_timeout is
big enough comparing to the sleep timeout specified from card's
EXT_CSD. If this isn't case, we use a R1 response instead of R1B and
fallback to use a delay instead.

Do note that a max_busy_timeout set to zero by the host, is interpreted
as it can cope with whatever timeout the mmc core provides it with.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Conform to the eMMC spec and use the CMD6 generic timeout from the
EXT_CSD register, when switching to HS200 mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

If the host controller supports busy detection in HW, we expect the
MMC_CAP_WAIT_WHILE_BUSY to be set. Likewise the corresponding
host->max_busy_timeout should reflect the maximum busy detection
timeout supported by the host.

Previously we expected a host that supported MMC_CAP_WAIT_WHILE_BUSY to
cope with any timeout, which just isn't feasible due to HW limitations.

For most switch operations, R1B responses are expected and thus we need
to check for busy detection completion. To cope with cases where the
requested busy detection timeout is greater than what the host are able
to support, we fallback to use a R1 response instead. This will prevent
the host from doing HW busy detection.

In those cases, busy detection completion is handled by polling the for
the card's status using CMD13. This is the same mechanism used when the
host doesn't support MMC_CAP_WAIT_WHILE_BUSY.

Do note, a host->max_busy_timeout set to zero, is interpreted by the
mmc core as it don't know what the host supports. It will then provide
the host with whatever timeout the mmc core finds suitable.

For some cases the mmc core has unfurtunate no clue of what timeout to
use. In these cases we provide the host with a timeout value of zero,
which the host may interpret as use whatever timeout it finds suitable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Instead of using several references to card->host, let's use a local
variable. That means we can remove the BUG_ON verifications for the
same pointers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.

This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.

Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Put myself as a (co)maintainer of the mmc subsystem to help out Chris
Ball in a more official role.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Add support for non-blocking request, pre_req() runs dma_map_sg() and
post_req() runs dma_unmap_sg(). This patch can increase card read/write
speed, especially for high speed card and slow CPU(for some embedded
platform).

Users can get a great benefit from this patch. if CPU frequency is 800MHz,
SDR104 or DDR50 card read/write speed may increase more than 15%.

test results:
intel i3(800MHz - 2.3GHz), SD card clock 208MHz

performance mode(2.3GHz):
Before:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.18191 s, 56.8 MB/s
After:
 dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.09276 s, 61.4 MB/s

powersave mode(800MHz):
Before:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.29569 s, 51.8 MB/s
After:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.11218 s, 60.3 MB/s
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

The new phase searching method is more concise and easier to
understand.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

If the host driver removed while card in the slot, the host will not
power off card power correctly. This bug is produced because host
eject flag set before the last mmc_set_ios callback, we should set the
eject flag after power off.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

This patch adds the erase capability to OMAP1/OMAP2420 MMC driver. Idea is
the same than in commit 93caf8e ("omap_hsmmc: add erase capability") that we
disable the data timeout interrupt for erases.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>