- 07 Aug, 2017 29 commits
-
-
Rob Herring authored
Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by:
Rob Herring <robh@kernel.org> Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Prabu Thangamuthu authored
As per internal decision, Joao Pinto will be maintainer for DWC UFS driver. Signed-off-by:
Prabu Thangamuthu <prabut@synopsys.com> Acked-by:
Joao Pinto <Joao.Pinto@synopsys.com> Signed-off-by:
-
Arnd Bergmann authored
gcc points out a theorerical string overflow: drivers/message/fusion/mptbase.c: In function 'mpt_detach': drivers/message/fusion/mptbase.c:2103:17: error: '%s' directive writing up to 31 bytes into a region of size 28 [-Werror=format-overflow=] sprintf(pname, MPT_PROCFS_MPTBASEDIR "/%s/summary", ioc->name); ^~~~~ drivers/message/fusion/mptbase.c:2103:2: note: 'sprintf' output between 13 and 44 bytes into a destination of size 32 We can simply double the size of the local buffer here to be on the safe side, and using snprintf() instead of sprintf() protects us if ioc->name was not terminated properly. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
We print a 256 byte event string into a buffer that is only 161 bytes long, this is clearly wrong: drivers/scsi/gdth_proc.c: In function 'gdth_show_info': drivers/scsi/gdth.c:3660:41: error: '%s' directive writing up to 255 bytes into a region of size between 141 and 150 [-Werror=format-overflow=] sprintf(buffer,"Adapter %d: %s\n", ^~ /git/arm-soc/drivers/scsi/gdth.c:3660:13: note: 'sprintf' output between 13 and 277 bytes into a destination of size 161 sprintf(buffer,"Adapter %d: %s\n", ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ dvr->eu.async.ionode,dvr->event_string); ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ gcc calculates that the worst case buffer size would be 277 bytes, so we can use that. Signed-off-by: -
Arnd Bergmann authored
The MSI interrupt name can require 11 bytes in addition to the device name, for a total of 23 bytes: drivers/scsi/fnic/fnic_isr.c: In function 'fnic_request_intr': drivers/scsi/fnic/fnic_isr.c:192:4: error: '-fcs-rq' directive writing 7 bytes into a region of size between 5 and 16 [-Werror=format-overflow=] "%.11s-fcs-rq", fnic->name); drivers/scsi/fnic/fnic_isr.c:206:3: note: 'sprintf' output between 12 and 23 bytes into a destination of size 16 sprintf(fnic->msix[FNIC_MSIX_ERR_NOTIFY].devname, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ "%.11s-err-notify", fnic->name); This extends the buffer to fit any possible value. Signed-off-by: -
Arnd Bergmann authored
gcc notices that we would overflow the buffer for the inquiry of the product name if we have too many adapters: drivers/scsi/gdth.c: In function 'gdth_next': drivers/scsi/gdth.c:2357:29: warning: 'sprintf' may write a terminating nul past the end of the destination [-Wformat-overflow=] sprintf(inq.product,"Host Drive #%02d",t); ^~~~~~~~~~~~~~~~~~~ drivers/scsi/gdth.c:2357:9: note: 'sprintf' output between 16 and 17 bytes into a destination of size 16 sprintf(inq.product,"Host Drive #%02d",t); This won't happen in practice, so just use snprintf to truncate the string. Signed-off-by: -
Arnd Bergmann authored
We print the driver name into one string and then add and ID and copy it into a second string of the same length, at which point gcc complains about a possible overflow: drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_probe': drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: error: '_cm' directive writing 3 bytes into a region of size between 1 and 32 [-Werror=format-overflow=] printf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id); ^~~~~~~~~ drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: note: directive argument in the range [0, 255] drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:2: note: 'sprintf' output between 5 and 38 bytes into a destination of size 32 sprintf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Making the first string shorter is sufficient to avoid the warning here, as we know it can only contain either "mpt2sas" or "mpt3sas". Signed-off-by: -
Arnd Bergmann authored
gcc-7 complains that the firmware version strings might overflow for some values: drivers/scsi/megaraid.c: In function 'megaraid_probe_one': drivers/scsi/megaraid.c:314:33: error: '%d' directive writing between 1 and 2 bytes into a region of size between 1 and 2 [-Werror=format-overflow=] drivers/scsi/megaraid.c:314:33: note: directive argument in the range [0, 15] drivers/scsi/megaraid.c:314:3: note: 'sprintf' output between 7 and 9 bytes into a destination of size 7 drivers/scsi/megaraid.c:320:35: error: '%d' directive writing between 1 and 2 bytes into a region of size between 1 and 2 [-Werror=format-overflow=] drivers/scsi/megaraid.c:320:35: note: directive argument in the range [0, 15] drivers/scsi/megaraid.c:320:3: note: 'sprintf' output between 7 and 9 bytes into a destination of size 7 This makes the code use a truncating snprintf() instead, which shuts up that warning. Signed-off-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. Signed-off-by:
Romain Perier <romain.perier@collabora.com> Acked-by:
Peter Senna Tschudin <peter.senna@collabora.com> Tested-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. Signed-off-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. Signed-off-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. Signed-off-by:
Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. It also updates some comments, accordingly. Signed-off-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. It also updates the name of some variables and the content of comments, accordingly. Signed-off-by:
-
Romain Perier authored
The PCI pool API is deprecated. This commit replaces the PCI pool old API by the appropriate function with the DMA pool API. Signed-off-by:
-
Ondrej Zary authored
Limit PDMA send to 512 B to avoid data corruption on DTC3181E. The corruption is always the same: one byte missing at the beginning of a 128 B block. It happens only with slow Quantum LPS 240 drive, not with faster IBM DORS-32160. It's not clear what causes this. Documentation for the DTC436 chip has not been made available. Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Tested-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Ondrej Zary authored
The polling loops in pread() and pwrite() can easily become infinite loops and hang the machine. Merge the IRQ check into host buffer wait loop and add polling limit. Also place a limit on polling for 53C80 registers accessibility. [Use NCR5380_poll_politely2() for register polling. Rely on polling for gated IRQ rather than polling for phase error, like the algorithm in the 53c400 datasheet. Move DTC436 workarounds into a separate patch. Factor-out common code as wait_for_53c80_access(). Rework the residual calculations. -- F.T.] Signed-off-by:
-
Finn Thain authored
The word "read" may be used to mean "DMA read operation" or "SCSI READ command", though a READ command implies writing to memory. Signed-off-by:
-
Finn Thain authored
Signed-off-by:
-
Ondrej Zary authored
When an IRQ arrives during PDMA transfer, pread() and pwrite() return without waiting for the 53C80 registers to be ready and this ends up messing up the chip state. This was observed with SONY CDU-55S which is slow enough to disconnect during 4096-byte reads. IRQ during PDMA is not an error so don't return -1. Instead, store the remaining byte count for use by NCR5380_dma_residual(). [Poll for the BASR_END_DMA_TRANSFER condition rather than remove the error message -- F.T.] Signed-off-by:
-
Ondrej Zary authored
generic_NCR5380_dma_xfer_len() incorrectly uses cmd->transfersize which causes rescan-scsi-bus and CD-ROM access to hang the system. Use cmd->SCp.this_residual instead, like other NCR5380 drivers. Signed-off-by:
-
Hannes Reinecke authored
When issuing a bus reset we should complete all commands, not just the command triggering the reset. Signed-off-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by:
-
Hannes Reinecke authored
To correctly identify which fib has a scsi command callback this patch implements a flag FIB_CONTEXT_FLAG_SCSI_CMD. Signed-off-by:
-
Hannes Reinecke authored
aac_hba_send() will return FAILED for any non-SCSI command requests, failing any TMFs. This patch updates the check to allow TMFs. Signed-off-by:
-
Hannes Reinecke authored
When sending a reset fib we shouldn't rely on the scsi command, but rather set the TMF status in the map_info->reset_state variable. That allows us to send a TMF independent on a scsi command. Signed-off-by:
-
Hannes Reinecke authored
Split off device, target, and bus reset functionality into individual functions. Signed-off-by:
-
Hannes Reinecke authored
Split off the host reset parts of aac_eh_reset() into a separate host reset function. Signed-off-by:
-
Hannes Reinecke authored
Split off reset FIB generation into separate functions. Signed-off-by:
-
Linus Torvalds authored
-
- 06 Aug, 2017 11 commits
-
-
git://git.infradead.org/linux-platform-drivers-x86Linus Torvalds authored
Pull x86 platform driver fix from Darren Hart: "Fix loop preventing some platforms from waking up via the power button in s2idle: - intel-vbtn: match power button on press rather than release" * tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86: platform/x86: intel-vbtn: match power button on press rather than release
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "A large number of ext4 bug fixes and cleanups for v4.13" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: fix copy paste error in ext4_swap_extents() ext4: fix overflow caused by missing cast in ext4_resize_fs() ext4, project: expand inode extra size if possible ext4: cleanup ext4_expand_extra_isize_ea() ext4: restructure ext4_expand_extra_isize ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize ext4: make xattr inode reads faster ext4: inplace xattr block update fails to deduplicate blocks ext4: remove unused mode parameter ext4: fix warning about stack corruption ext4: fix dir_nlink behaviour ext4: silence array overflow warning ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize ext4: release discard bio after sending discard commands ext4: convert swap_inode_data() over to use swap() on most of the fields ext4: error should be cleared if ea_inode isn't added to the cache ext4: Don't clear SGID when inheriting ACLs ext4: preserve i_mode if __ext4_set_acl() fails ext4: remove unused metadata accounting variables ext4: correct comment references to ext4_ext_direct_IO()
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS fixes from Ralf Baechle: "This fixes two build issues for ralink platforms, both due to missing #includes which used to be included indirectly via other headers" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: ralink: mt7620: Add missing header MIPS: ralink: Fix build error due to missing header
-
Dmitry V. Levin authored
The latest change of compat_sys_sigpending in commit 8f13621a ("sigpending(): move compat to native") has broken it in two ways. First, it tries to write 4 bytes more than userspace expects: sizeof(old_sigset_t) == sizeof(long) == 8 instead of sizeof(compat_old_sigset_t) == sizeof(u32) == 4. Second, on big endian architectures these bytes are being written in the wrong order. This bug was found by strace test suite. Reported-by:
Anatoly Pugachev <matorola@gmail.com> Inspired-by:
Eugene Syromyatnikov <evgsyr@gmail.com> Fixes: 8f13621a ("sigpending(): move compat to native") Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Maninder Singh authored
This bug was found by a static code checker tool for copy paste problems. Signed-off-by:
Maninder Singh <maninder1.s@samsung.com> Signed-off-by:
Vaneet Narang <v.narang@samsung.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu>
-
Jerry Lee authored
On a 32-bit platform, the value of n_blcoks_count may be wrong during the file system is resized to size larger than 2^32 blocks. This may caused the superblock being corrupted with zero blocks count. Fixes: 1c6bd717Signed-off-by:
Jerry Lee <jerrylee@qnap.com> Signed-off-by:
-
Miao Xie authored
When upgrading from old format, try to set project id to old file first time, it will return EOVERFLOW, but if that file is dirtied(touch etc), changing project id will be allowed, this might be confusing for users, we could try to expand @i_extra_isize here too. Reported-by:
Zhang Yi <yi.zhang@huawei.com> Signed-off-by:
Miao Xie <miaoxie@huawei.com> Signed-off-by:
Wang Shilong <wshilong@ddn.com> Signed-off-by:
-
Miao Xie authored
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer. Signed-off-by:
-
Miao Xie authored
Current ext4_expand_extra_isize just tries to expand extra isize, if someone is holding xattr lock or some check fails, it will give up. So rename its name to ext4_try_to_expand_extra_isize. Besides that, we clean up unnecessary check and move some relative checks into it. Signed-off-by:
-
Miao Xie authored
We should avoid the contention between the i_extra_isize update and the inline data insertion, so move the xattr trylock in front of i_extra_isize update. Signed-off-by:
-
Tahsin Erdogan authored
ext4_xattr_inode_read() currently reads each block sequentially while waiting for io operation to complete before moving on to the next block. This prevents request merging in block layer. Add a ext4_bread_batch() function that starts reads for all blocks then optionally waits for them to complete. A similar logic is used in ext4_find_entry(), so update that code to use the new function. Signed-off-by:
Tahsin Erdogan <tahsin@google.com> Signed-off-by:
-
