Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of a workaround for a hardware erratum in the SFC9100 family
(SF bug 35388), the TX_DESC_UPD_DWORD register address is also used
for communicating with the event block, and only descriptor pointer
values < 2048 are valid.

If the TX DMA ring size is increased to 4096 descriptors (which the
firmware still allows) then we may write a descriptor pointer
value >= 2048, which has entirely different and undesirable effects!

Limit the TX DMA ring size correctly when this workaround is in
effect.

Fixes: 8127d661 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I will be taking over the work from Ben Hutchings.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the practice set by commit 0afb1666 "vxlan: Add capability
of Rx checksum offload for inner packet" is applied when the skb
goes through the portion of the RX code which is shared between
vxlan netdevices and ovs vxlan port instances.

Cc: Joseph Gasparakis <joseph.gasparakis@intel.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In this situation then ARRAY_SIZE() and sizeof() are the same, but we're
really dealing with array indexes and not byte offsets so ARRAY_SIZE()
is cleaner.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit a6222602("ip_tunnel: fix kernel panic with icmp_dest_unreach")
clear IPCB in ip_tunnel_xmit()  , or else skb->cb[] may contain garbage from
GSO segmentation layer.

But commit 0e6fbc5b("ip_tunnels: extend iptunnel_xmit()") refactor codes,
and it clear IPCB behind the dst_link_failure().

So clear IPCB in ip_tunnel_xmit() just like commti a6222602("ip_tunnel:
fix kernel panic with icmp_dest_unreach").
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We possibly retrieve the adapter's statistics during EEH recovery
and that should be disallowed. Otherwise, it would possibly incur
replicate EEH error and EEH recovery is going to fail eventually.

The patch reuses statistics lock and checks net_device is attached
before going to retrieve statistics, so that the problem can be
avoided.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we have EEH error happens to the adapter and we have to remove
it from the system for some reasons (e.g. more than 5 EEH errors
detected from the device in last hour), the adapter will be disabled
for towice separately by eeh_err_detected() and remove_one(), which
will incur following unexpected backtrace. The patch tries to avoid
it.

WARNING: at drivers/pci/pci.c:1431
CPU: 12 PID: 121 Comm: eehd Not tainted 3.13.0-rc7+ #1
task: c0000001823a3780 ti: c00000018240c000 task.ti: c00000018240c000
NIP: c0000000003c1e40 LR: c0000000003c1e3c CTR: 0000000001764c5c
REGS: c00000018240f470 TRAP: 0700   Not tainted  (3.13.0-rc7+)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI>  CR: 28000024  XER: 00000004
CFAR: c000000000706528 SOFTE: 1
GPR00: c0000000003c1e3c c00000018240f6f0 c0000000010fe1f8 0000000000000035
GPR04: 0000000000000000 0000000000000000 00000000003ae509 0000000000000000
GPR08: 000000000000346f 0000000000000000 0000000000000000 0000000000003fef
GPR12: 0000000028000022 c00000000ec93000 c0000000000c11b0 c000000184ac3e40
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 c0000000009398d8 c00000000101f9c0 c0000001860ae000
GPR28: c000000182ba0000 00000000000001f0 c0000001860ae6f8 c0000001860ae000
NIP [c0000000003c1e40] .pci_disable_device+0xd0/0xf0
LR [c0000000003c1e3c] .pci_disable_device+0xcc/0xf0
Call Trace:
[c0000000003c1e3c] .pci_disable_device+0xcc/0xf0 (unreliable)
[d0000000073881c4] .remove_one+0x174/0x320 [cxgb4]
[c0000000003c57e0] .pci_device_remove+0x60/0x100
[c00000000046396c] .__device_release_driver+0x9c/0x120
[c000000000463a20] .device_release_driver+0x30/0x60
[c0000000003bcdb4] .pci_stop_bus_device+0x94/0xd0
[c0000000003bcf48] .pci_stop_and_remove_bus_device+0x18/0x30
[c00000000003f548] .pcibios_remove_pci_devices+0xa8/0x140
[c000000000035c00] .eeh_handle_normal_event+0xa0/0x3c0
[c000000000035f50] .eeh_handle_event+0x30/0x2b0
[c0000000000362c4] .eeh_event_handler+0xf4/0x1b0
[c0000000000c12b8] .kthread+0x108/0x130
[c00000000000a168] .ret_from_kernel_thread+0x5c/0x74
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable promiscuous mode support for CPSW.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we have multiple devices attempting to sync the same address
to a single destination, each device should be permitted to sync
it once.  To accomplish this, pass the 'sync_cnt' of the source
address when adding the addresss to the lower device.  'sync_cnt'
tracks how many time a given address has been succefully synced.
This way, we know that if the 'sync_cnt' passed in is 0, we should
sync this address.

Also, turn 'synced' member back into the counter as was originally
done in
   commit 4543fbef.
   net: count hw_addr syncs so that unsync works properly.
It tracks how many time a given address has been added via a
'sync' operation.  For every successfull 'sync' the counter is
incremented, and for ever 'unsync', the counter is decremented.
This makes sure that the address will be properly removed from
the the lower device when all the upper devices have removed it.
Reported-by: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru>
CC: Konstantin Ushakov <Konstantin.Ushakov@oktetlabs.ru>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed few issues around using __rcu prefix and rcu_assign_pointer, also
fixed a warning print to use ntohs(port) and not htons(port).

net/ipv4/udp_offload.c:112:9: error: incompatible types in comparison expression (different address spaces)
net/ipv4/udp_offload.c:113:9: error: incompatible types in comparison expression (different address spaces)
net/ipv4/udp_offload.c:176:19: error: incompatible types in comparison expression (different address spaces)
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A socket may be v6/v4-mapped. In that case sk->sk_family is AF_INET6,
but the IP being used is actually an IPv4-address.
Current's tcp-metrics will thus represent it as an IPv6-address:

root@server:~# ip tcp_metrics
::ffff:10.1.1.2 age 22.920sec rtt 18750us rttvar 15000us cwnd 10
10.1.1.2 age 47.970sec rtt 16250us rttvar 10000us cwnd 10

This patch modifies the tcp-metrics so that they are able to handle the
v6/v4-mapped sockets correctly.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 8df8c56a, 6lowpan_iphc is a module of its own.

Unfortunately, it lacks some infrastructure to behave like a
good kernel citizen:

  kernel: 6lowpan_iphc: module license 'unspecified' taints kernel.
  kernel: Disabling lock debugging due to kernel taint

This patch adds the basic MODULE_LICENSE(); with GPL license:
the code was copied from net/ieee802154/6lowpan.c which is GPL
and the module exports symbol with EXPORT_SYMBOL_GPL();.

Cc: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like bonding, team as netdevice doesn't cross netns boundaries.

Team ports and team itself live in same netns.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like bridge, bonding as netdevice doesn't cross netns boundaries.

Bonding ports and bonding itself live in same netns.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used API bond-specific can be removed now. This is now handled
in a generic way in rtnl_link_ops.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88a)

Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.

This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow user to identify easily what the attributes are related to. Change
the name of the group to "bonding_slave" to be similar to master which
is named "bonding".
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Workqueue used in neighbour layer have no real dependency of scheduling these on
the cpu which scheduled them.

On a idle system, it is observed that an idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.

This patch replaces normal workqueues with power efficient versions. This
doesn't change existing behavior of code unless CONFIG_WQ_POWER_EFFICIENT is
enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Workqueue used in ipv4 layer have no real dependency of scheduling these on the
cpu which scheduled them.

On a idle system, it is observed that an idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.

This patch replaces normal workqueues with power efficient versions. This
doesn't change existing behavior of code unless CONFIG_WQ_POWER_EFFICIENT is
enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change allows to consider an anycast address valid as source address
when given via an IPV6_PKTINFO or IPV6_2292PKTINFO ancillary data item.
So, when sending a datagram with ancillary data, the unicast and anycast
addresses are handled in the same way.

- Adds ipv6_chk_acast_addr_src() to check if an anycast address is link-local
  on given interface or is global.
- Uses it in ip6_datagram_send_ctl().
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A patch for fixing a race between queue selection and changing queues
was introduced in commit 92bb73ea("tuntap: fix a possible race between
queue selection and changing queues").

The fix was to prevent the driver from re-reading the tun->numqueues
more than once within tun_select_queue() using ACCESS_ONCE().

We have been experiancing 'Divide-by-zero' errors in tun_net_xmit()
since we moved from 3.6 to 3.10, and believe that they come from a
simular source where the value of tun->numqueues changes to zero
between the first and a subsequent read of tun->numqueues.

The fix is a simular use of ACCESS_ONCE(), as well as a multiply
instead of a divide in the if statement.
Signed-off-by: Dominic Curran <dominic.curran@citrix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Max Krasnyansky <maxk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

br_handle_vlan() pushes HW accelerated vlan tag into skbuff when outgoing
port is the bridge device.
This is unnecessary because __netif_receive_skb_core() can handle skbs
with HW accelerated vlan tag. In current implementation,
__netif_receive_skb_core() needs to extract the vlan tag embedded in skb
data. This could cause low network performance especially when receiving
frames at a high frame rate on the bridge device.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In bbf852b9 I introduced the tmlist, which allows to delete
multiple entries from the cache that match a specified destination if no
source-IP is specified.

However, as the cache is an RCU-list, we should not create this tmlist, as
it will change the tcpm_next pointer of the element that will be deleted
and so a thread iterating over the cache's entries while holding the
RCU-lock might get "redirected" to this tmlist.

This patch fixes this, by reverting back to the old behavior prior to
bbf852b9, which means that we simply change the tcpm_next
pointer of the previous element (pp) to jump over the one we are
deleting.
The difference is that we call kfree_rcu() directly on the cache entry,
which allows us to delete multiple entries from the list.

Fixes: bbf852b9 (tcp: metrics: Delete all entries matching a certain destination)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ding Tianhong says:

====================
bonding: fix primary problem for bonding

If the slave's name changed, and the bond params primary is exist,
the bond should deal with the situation in two ways:

1) If the slave was the primary slave yet, clean the primary slave
   and reselect active slave.
2) If the slave's new name is as same as bond primary, set the slave
   as primary slave and reselect active slave.

If the new primary is not matching any slave in the bond, the bond should
record it to params, clean the primary slave and select a new active slave.

Update bonding.txt for primary description.

v2.1->v1: Because there are too many indentions and useless verification, so rewrite
	  the logic for updating the primary slave.
	  Modify some comments for to clean the typos.

v3->v2.1: Veaceslav disagree the first patch and modify the logic for it
	  (bonding: update the primary slave when changing slave's name)
	  and resend it himself (bonding: handle slave's name change with primary_slave logic),
	  so remove the first patch and send the last two patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the new primay is not matching any slave in the bond, the bond should
record it to params, clean the primary slave and select a new active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per suggestion from Eric W. Biederman, vxlan should be using
{un,}register_pernet_subsys() instead of {un,}register_pernet_device()
to ensure the vxlan_net structure is initialized before and cleaned
up after all network devices in a given network namespace i.e. when
dealing with network notifiers. This is similarly handeled already in
commit 91e2ff35 ("net: Teach vlans to cleanup as a pernet subsystem")
and, thus, improves upon fd27e0d4 ("net: vxlan: do not use vxlan_net
before checking event type"). Just as in 91e2ff35, we do not need
to explicitly handle deletion of vxlan devices as network namespace
exit calls dellink on all remaining virtual devices, and
rtnl_link_unregister() calls dellink on all outstanding devices in that
network namespace, so we can entirely drop the pernet exit operation
as well. Moreover, on vxlan module exit, rcu_barrier() is called by
netns since commit 3a765eda ("netns: Add an explicit rcu_barrier
to unregister_pernet_{device|subsys}"), so this may be omitted. Tested
with various scenarios and works well on my side.
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the class in skb->priority is not a leaf, apply filters from the
selected class, not the qdisc. This lets netfilter or user space
partially classify the packet.
Signed-off-by: Harry Mason <harry.mason@smoothwall.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a queue mapping mode to the fanout operation of af_packet
sockets.  This allows user space af_packet users to better filter on flows
ingressing and egressing via a specific hardware queue, and avoids the potential
packet reordering that can occur when FANOUT_CPU is being used and irq affinity
varies.

Tested successfully by myself.  applies to net-next
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bonding: introduce new option API

This patchset's goal is to introduce a new option API which should be used
to properly describe the bonding options with their mode dependcies and
requirements. With this patchset applied we get centralized option
manipulation, automatic RTNL acquire per option setting, automatic option
range checking, mode dependcy checking and other various flags which are
described in detail in patch 01's commit message and comments.
Also the parameter passing is changed to use a specialized structure which
is initialized to a value depending on the needs.
The main exported functions are:
 __bond_opt_set() - set an option (RTNL should be acquired prior)
 bond_opt_init(val|str) - init a bond_opt_value struct for value or string
                          parameter passing
 bond_opt_tryset_rtnl() - function which tries to acquire rtnl, mainly used
                          for sysfs
 bond_opt_parse - used to parse or check for valid values
 bond_opt_get - retrieve a pointer to bond_option struct for some option
 bond_opt_get_val - retrieve a pointer to a bond_opt_value struct for
                    some value

The same functions are used to set an option via sysfs and netlink, just
the parameter that's passed is usually initialized in a different way.
The converted options have multiple style fixes, there're some longer
lines but they looked either ugly or were strings/pr_warnings, if you
think some line would be better broken just let me know :-) there're
also a few sscanf false-positive warnings.
I decided to keep the "unsuppmodes" way of mode dep checking since it's
straight forward, if we make a more general way for checking dependencies
it'll be easy to change it.

Future plans for this work include:
 - Automatic sysfs generation from the bond_opts[].
 - Use of the API in bond_check_params() and thus cleaning it up (this has
   actually started, I'll take care of the rest in a separate patch)
 - Clean up all option-unrelated files of option definitions and functions

I've tried to leave as much documentation as possible, if there's anything
unclear please let me know. One more thing, I haven't moved all
option-related functions from bonding.h to the new bond_options.h, this
will be done in a separate patch, it's in my todo list.

This patchset has been tested by setting each converted option via sysfs
and netlink to a couple of wrong values, a couple of correct values and
some random values, also for the opts that have flags they have been
tested as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the necessary changes so slaves would use
the new bonding option API. Also move the option to its own set function
in bond_options.c and fix some style errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the necessary changes so lp_interval would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the necessary changes so resend_igmp would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the necessary changes so all_slaves_active would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the necessary changes so queue_id would use
the new bonding option API. Also move it to its own set function in
bond_options.c and fix some style errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the necessary changes so active_slave would use
the new bonding option API. Also some trivial/style fixes.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>