Currently the iseries_veth driver contravenes the specification in
Documentation/networking/driver.txt, in that if packets are not acked by
the other LPAR they will sit around forever.

This patch adds a per-connection timer which fires if we've had no acks for
five seconds. This is superior to the generic TX timer because it catches
the case of a small number of packets being sent and never acked.

This fixes a bug we were seeing on real systems, where some IPv6 neighbour
discovery packets would not be acked and then prevent the module from being
removed, due to skbs lying around.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver uses the generic TX timeout watchdog, however a better
solution is in the works, so remove this code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver can attach to multiple vlans, which correspond to
multiple net devices. However there is only 1 connection between each LPAR,
so the connection structure may be shared by multiple net devices.

This makes module removal messy, because we can't deallocate the connections
until we know there are no net devices still using them. The solution is to
use ref counts on the connections, so we can delete them (actually stop) as
soon as the ref count hits zero.

This patch fixes (part of) a bug we were seeing with IPv6 sending probes to
a dead LPAR, which would then hang us forever due to leftover skbs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch makes veth_init_connection() and veth_destroy_connection()
symmetrical in that they allocate/deallocate the same data.

Currently if there's an error while initialising connections (ie. ENOMEM)
we call veth_module_cleanup(), however this will oops because we call
driver_unregister() before we've called driver_register(). I've never seen
this actually happen though.

So instead we explicitly call veth_destroy_connection() for each connection,
any that have been set up will be deallocated.

We also fix a potential leak if vio_register_driver() fails.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver unconditionally calls dma_unmap_single() even
when the corresponding dma_map_single() may have failed.

Rework the code a bit to keep the return value from dma_unmap_single()
around, and then check if it's a dma_mapping_error() before we do
the dma_unmap_single().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver uses atomic ops to manipulate the in_use field of
one of its per-connection structures. However all references to the
flag occur while the connection's lock is held, so the atomic ops aren't
necessary.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver keeps a stack of messages for each connection
and a lock to protect the stack. However there is also a per-connection lock
which makes the message stack lock redundant.

Remove the message stack lock and document the fact that callers of the
stack-manipulation functions must hold the connection's lock.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Due to a logic bug, once promiscuous mode is enabled in the iseries_veth
driver it is never disabled.

The driver keeps two flags, promiscuous and all_mcast which have exactly the
same effect. This is because we only ever receive packets destined for us,
or multicast packets. So consolidate them into one promiscuous flag for
simplicity.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver contains a state machine which is used to manage
how connections are setup and neogotiated between LPARs.

If one side of a connection resets for some reason, the two LPARs can get
stuck in a race to re-setup the connection. This can lead to the connection
being declared dead by one or both ends. In practice the connection is
declared dead by one or both ends approximately 8/10 times a connection is
reset, although it is rare for connections to be reset.

(an example here: http://michael.ellerman.id.au/files/misc/veth-trace.html)

The core of the problem is that the end that resets the connection doesn't
wait for the other end to become aware of the reset. So the resetting end
starts setting the connection back up, and then receives a reset from the
other end (which is the response to the initial reset). And so on.

We're severely limited in what we can do to fix this. The protocol between
LPARs is essentially fixed, as we have to interoperate with both OS/400
and old Linux drivers. Which also means we need a fix that only changes the
code on one end.

The only fix I've found given that, is to just blindly sleep for a bit when
resetting the connection, in the hope that the other end will get itself
sorted.  Needless to say I'd love it if someone has a better idea.

This does work, I've so far been unable to get it to break, whereas without
the fix a reset of one end will lead to a dead connection ~8/10 times.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The iseries_veth driver has a timer which we use to send acks. When the
connection is reset or stopped we need to delete the timer.

Currently we only call del_timer() when resetting a connection, which means
the timer might run again while the connection is being re-setup. As it turns
out that's ok, because the flags the timer consults have been reset.

It's cleaner though to call del_timer_sync() once we've dropped the lock,
although the timer may still run between us dropping the lock and calling
del_timer_sync(), but as above that's ok.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Currently the iseries_veth driver prints the file name and line number in its
error messages. This isn't very useful for most users, so just print
"iseries_veth: message" instead.

 - convert uses of veth_printk() to veth_debug()/veth_error()/veth_info()
 - make terminology consistent, ie. always refer to LPAR not lpar
 - be consistent about printing return codes as %d not %x
 - make format strings fit in 80 columns
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

BZ# 4475.

Noted in BZ# 2960.

The following patch fixes two warnings in arch/ppc/syslib/m8xx_setup.c
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

I had some time to think about PCI assign issues in 2.6.13-rc series.

The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:

 /**
  * Reserve motherboard resources after PCI claim BARs,
  * but before PCI assign resources for uninitialized PCI devices
  */

So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.

Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
  it duplicates pci_assign_unassigned_resources() functionality and
  actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
  settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
  various setups.

Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

USB generic driver
When a USB error occurs that might indicate that the device has been
unplugged, don't resubmit the URB immediately to prevent flooding the
log with error messages before khubd has us disconnect()ed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>

Add register_sound_special_device() function to allow assignment of
device pointer to a specific OSS device for HAL.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

EMU10K1/EMU10K2 driver
Add identification for Live 5.1 [SB0220]
Signed-off-by: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

EMU10K1/EMU10K2 driver
Added the missing ac97 support on SBLive! Player 5.1.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Intel8x0 driver
Added ac97_quirk for FSC 4010.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

PCM Midlevel
Fixed zero-division bug in PCM 32bit compat layer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Intel8x0 driver
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

USB generic driver
Emagic devices pad their packets not with 0xff bytes but with a 0xff
byte followed by garbage, so we have to stop at the first such byte.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>

au88x0 driver,Common EMU synth
Fixed missing spin_unlock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

GUS Library
'extern inline' doesn't make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HDA Intel driver
Fix and clean up for the support of ULI M5461
- set CORB/RIRB sizes explicitly
- add workarounds for ULI on ia32
- max number of streams depends on the chip type now
- increase the size of BDL
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HDA Codec driver
Added the missing beep support for Uniwill laptop (ALSA bug#1358).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Digigram VX Pocket driver
Add snd_card_set_dev() to register the device pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Digigram VX Pocket driver
Fixed the wrong index number assignment.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Digigram VX Pocket driver
Added the missing event callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Memalloc module
Fix an error when built without CONFIG_PROC_FS.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HDA Codec driver
Use struct instead of array to improve the readability of hda_codec.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HDA Codec driver
The insertion of the rate 9600 make a shift in detection of supported
rate, put this rate at the end of the list.
Signed-off-by: Nicolas Graziano <nicolas.graziano@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Intel8x0 driver,AC97 Codec
The HP nx6110 laptop needs to have Headphone Jack Sense enabled so
that the internal speakers will be turned off when headphones are
plugged in.

Also ac97_quirk=hp_only is needed to make a single Master volume in
the mixer instead of separate volumes for internal speakers and
headphones, which just confuses the user.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>