The DMA ring seems to be stable now.

v2: remove pt_ring_index as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Stop fiddling with jiffies, always wait for RADEON_FENCE_JIFFIES_TIMEOUT.
Consolidate the two wait sequence implementations into just one function.
Activate all waiters and remember if the reset was already done instead of
trying to reset from only one thread.

v2: clear reset flag earlier to avoid timeout in IB test
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It is said to cause hangs.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The parameter is in bytes not dwords.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Make sure the UVD clocks are still active before sending
the destroy message, otherwise the hw might hang.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Typo in the register offset.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The buffers needs to be in little endian format.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If the user has forced the state high or low, retain that preference
even when we switch power states.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=70654Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If the thermal state is active, we are in the lowest performance level
to cool down the chip.  Don't let the user force it higher.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems to be stable on them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems to be stable on them.  There are still some issues
with the performance states staying in the highest levels
on certain cards when multiple monitors are attached, but
being that the the cards are always in their highest power
state at boot up anyway, this doesn't really change anything
and improves things in all other cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems to be stable on them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems to be stable on them and improves peformance
as most SI asics have very low boot clocks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

DPM seems to be stable on these asics and it drastically
improves performance depending on the boot clocks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Avoids spamming the system log for chips where dpm is enabled by
default, but prints then messages when users force it on for other
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently radeon devices are not properly shutdown during kexec. This
causes a varity of issues, e.g. dpm initialization failures.
Fix this by implementing a radeon_pci_shutdown function, that unloads
the driver cleanly.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

No need to continue with the loops once we've matched
the appropriate connector.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The plain [EN|DIS]ABLE functions do the same thing and more
and aren't broken on some systems like [EN|DIS]ABLE_OUTPUT.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The plain [EN|DIS]ABLE functions do the same thing and more
and aren't broken on some systems like [EN|DIS]ABLE_OUTPUT.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On SI asics, the SMC will automatically force the performance
level to the lowest level if there are no displays active.  This
prevents automatic performance scaling on PowerXpress systems or
for offscreen rendering or compute when displays are disabled.

Going forward, it would be best to dynamically change this, but
for now leave scaling enabled.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69395Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Uses the CP ring rather than the DMA ring.  Useful
for debugging and benchmarking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The rv6xx_clocks_per_unit() function pretends it can set flags in a u64
bitfield but really because "1" is an int it doesn't work for more than
32 bits.  The only caller truncates the high bits away anyway.  I've
just changed it to be a u32.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Uses CP DMA packet just like previous asics.
Useful for debugging and benchmarking.  Uses
same packet format as prior asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems to be stable enough for the majority of users.
It can be disabled on the fly via connector attributes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This hooks radeon up to the runtime PM system to enable
dynamic power management for secondary GPUs in switchable
and powerxpress laptops.

v2: agd5f: clean up, add module parameter
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is a pre-requisite for runtime pm on powerxpress systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Allows you to enable dither in the display hardware
when the monitor supports lower a lower bpc than the
current framebuffer format.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The FMT blocks control how data is sent from the backend
of the display pipe to to monitor.  Proper set up of the
FMT blocks are required for 30bpp formats.  Additionally,
dithering can be enabled on for better display with 18 and
24bpp displays.  The exception is LVDS/eDP which atom
takes care of in the SelectCRTC_Source table.  For now
just enable truncation until we test dithering more.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

device_unregister() already drops its reference to the struct device, so
explicitly calling put_device() before device_unregister() can cause the
device to have been freed before it can be unregistered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel into drm-next

- CRC support from Damien and He Shuang. Long term this should allow us to
  test an awful lot modesetting corner cases automatically. So for me as
  the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
  helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.

* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
  drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
  drm/i915: remove dead code in ironlake_crtc_mode_set
  drm/i915: crc support for hsw
  drm/i915: fix CRC debugfs setup
  drm/i915: wait one vblank when disabling CRCs
  drm/i915: use ->get_vblank_counter for the crc frame counter
  drm/i915: wire up CRC interrupt for ilk/snb
  drm/i915: add CRC #defines for ilk/snb
  drm/i915: extract display_pipe_crc_update
  drm/i915: don't Oops in debugfs for I915_FBDEV=n
  drm/i915: set HDMI pixel clock in audio configuration
  drm/i915: pass mode to ELD write vfuncs
  cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
  drm/i915: check gem bo size when creating framebuffers
  drm/i915: Use unsigned long for obj->user_pin_count
  drm/i915: prevent tiling changes on framebuffer backing storage
  drm/i915: grab dev->struct_mutex around framebuffer_init
  drm/i915: vlv: fix VGA hotplug after modeset
  drm: add support for additional stereo 3D modes
  drm/i915: preserve dispaly init order on ByT
  ...

To disable a monitor, a Spice client sends a monitor config with the
monitor resolution to 0x0.

However, before qxl_crtc_disable() is reached after the hotplug event,
it can happen that another monitor is reconfigured, and
qxl_send_monitors_config() is called with the old config, which will
re-enable the monitor on the client.

Reset config if monitor is found disconnected, during
drm_helper_hpd_irq_event().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

All hard-coded resolutions are passing this check.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

By default, 1024x768 is the preferred resolution. However, when a
monitor config is given, it should be the only preferred resolution.

Note that the monitor config resolution is passed to
qxl_add_common_modes() to avoid adding a duplicate mode without the
preferred resolution. That would discard the previous monitor config
preferred bit.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

In commit 38d5487d, Keith explained:
    This patch simply merges the two mode type bits together; that seems
    reasonable to me, but perhaps only a subset of the bits should be
    used? None of these can be user defined as they all come from
    looking at just the hardware.

However, merging the bits means that a flag becomes sticky. It is not
possible, for example to update the mode type to remove the
DRM_MODE_TYPE_PREFERRED bit.

After a brief discussion with Dave Airlie on irc, it was agreed to
propose that change, instead of introducing another function to remove a
bit from exisiting modes type.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm_helper_hpd_irq_event() only notifies when the connector status
changed. However, Spice monitor config can change while the connector is
connected, to support arbitrary resolution. Do an hotplug event if it
wasn't done by drm_helper_hpd_irq_event().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The caller may want to know whether the configuration was changed, and
if an hotplug event was sent.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Fix a little spelling of drm_crtc_convert_umode() comment.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>