As suggested by David Daney.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Don't assume they are there, the device tree will tell us.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9461/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Without this, we get bus errors.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9460/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some hardware blocks attached to the OCTEON bootbus run asynchronously
to accesses from the CPUs.  These include MMC/SD host, CF(when using
DMA), and NAND controller.  A bus error, or corrupt data may occur if
a CPU is trying to access a bootbus connected device at the same time
the bus is running asynchronous operations.

To work around these problems we add this semaphore that must be
acquired before initiating bootbus activity.  Subsequent patches will
add users for this.
Signed-off-by: David Daney <david.daney@cavium.com>
[aleksey.makarov@auriga.com: combine the patches]
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Chandrakala Chavva <cchavva@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9459/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Most of the supported chips use legacy (non-DT) bootloaders, so they will
need to select an appropriate builtin DTB at compile time until the
bootloader is updated.  Provide suitable DTS files, and a means to compile
one of them into the kernel image.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: f.fainelli@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8858/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add an entry for each supported Broadcom SoC.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: f.fainelli@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8857/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The DT bindings for this platform have changed as the bootloader and
product requirements evolved.  In particular, there are both
Linux-on-Zephyr and Linux-on-Viper configurations.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8856/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Also, add an LE defconfig for set-top box (BCM7xxx).  This will allow the
BMIPS kernel to run on several non-BCM3384 platforms.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: f.fainelli@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8855/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This will be required to support BMIPS3300 platforms.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8854/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

BCM3384/BCM63xx can use the common drivers/irqchip/irq-bcm7120-l2.c for
this purpose; BCM7xxx will use drivers/irqchip/irq-bcm7038-l1.c.  We no
longer need this code under arch/mips.

[ralf@linux-mips.org: Fix conflicts.]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8853/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

A couple of chips require special handling in order to make SMP secondary
boot and/or exception vectors work correctly.  Take care of these in
setup.c.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8852/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

There is no "bcm3384" bus so let's just remove it to avoid confusion.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8851/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is a more standardized way of handling DMA remapping, and it is
suitable for the memory map found on BCM3384.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8850/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add a new section covering the Generic BMIPS machine type.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8849/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Enabling support for more than one BMIPS CPU in the same build may
result in different L1_CACHE_SHIFT values, e.g.

    CPU_BMIPS5000 selects MIPS_L1_CACHE_SHIFT_7
    CPU_BMIPS4380 selects MIPS_L1_CACHE_SHIFT_6
    anything else defaults to MIPS_L1_CACHE_SHIFT_5

Ensure that if more than one MIPS_L1_CACHE_SHIFT_x option is selected,
Kconfig sets CONFIG_MIPS_L1_CACHE_SHIFT to the highest value.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8847/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some machines only have one bus type to register (e.g. "simple-bus").
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8845/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is the main peripheral IRQ controller on the BCM7xxx MIPS chips;
it has the following characteristics:

 - 64 to 160+ level IRQs
 - Atomic set/clear registers
 - Reasonably predictable register layout (N status words, then N
   mask status words, then N mask set words, then N mask clear words)
 - SMP affinity supported on most systems
 - Typically connected to MIPS IRQ 2,3,2,3 on CPUs 0,1,2,3

This driver registers one IRQ domain and one IRQ chip to cover all
instances of the block.  Up to 4 instances of the block may appear, as
it supports 4-way IRQ affinity on BCM7435.

The same block exists on the ARM BCM7xxx chips, but typically the ARM GIC
is used instead.  So this driver is primarily intended for MIPS STB chips.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8844/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

These controllers support multiple enable/status pairs (64+ IRQs),
can put the enable/status words at different offsets, and do not
support multiple parent IRQs.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8843/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The BCM7xxx instances of this block (listed in the register manual as
simply "IRQ0") all have the following items in common:

 - brcm,int-map-mask: for routing different bits in the L2 to different
   parent IRQs

 - brcm,int-fwd-mask: for hardwiring certain IRQs to bypass the L2 and
   use dedicated L1 lines

 - one enable/status pair (32 bits only)

Much of the driver code can be shared with BCM3380-style controllers, but
in order to do this cleanly, let's split out the BCM7xxx-specific logic
first.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8842/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Currently the driver assumes that REG_BASE+0x00 is the IRQ enable mask,
and REG_BASE+0x04 is the IRQ status mask.  This is true on BCM3384 and
BCM7xxx, but it is not true for some of the controllers found on BCM63xx
chips.  So we will change a couple of key assumptions:

 - Don't assume that both the IRQEN and IRQSTAT registers will be
   covered by a single ioremap() operation.

 - Don't assume any particular ordering (IRQSTAT might show up before
   IRQEN on some chips).

 - For an L2 controller with >=64 IRQs, don't assume that every
   IRQEN/IRQSTAT pair will use the same register spacing.

This patch changes the "plumbing" but doesn't yet provide a way for users
to instantiate a controller with arbitrary IRQEN/IRQSTAT offsets.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8841/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Wakeable interrupts might be pending at boot/init time, because wakeup
interrupts might have triggered a resume from S5. So don't clear such
wakeups.

This means that any driver which requests a wakeable interrupt bit
should be prepared to handle an interrupt as soon as they call
request_irq(). (This is technically already the correct development
practice, but some drivers probably expect not to receive interrupts
until they have performed some I/O.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8840/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Several drivers now use this API, including the ARM GIC driver, so remove
the outdated comment.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8839/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This platform is configured primarily through device tree, and we can
reuse the same code to support a bunch of other chips.  Change the name
to reflect this.

[ralf@linux-mips.org: Fix conflicts with other patches.]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8838/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add the dtbs_install Makefile target to install the dtb files into
$INSTALL_DTBS_PATH.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8836/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Move the MIPS device-trees into the appropriate vendor sub-directories.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8835/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

With sched_clock being ready, it makes sense to add the option of IRQ time
accounting -- When we have a fast enough sched_clock, IRQ time accounting
will be enabled (see sched_clock_register).
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9489/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use sb1250 hpt for sched_clock source. This implementation will give high
resolution cputime accounting.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9488/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is to make checkpatch.pl happy for the next patch. It would otherwise
say --

ERROR: Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already includes
a copy of the GPL.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9487/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is to prepare for the upcoming read_sched_clock implementation, which
will also need to get cycles from the high precision timer.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9486/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use jz4740 timer counter for sched_clock source. This implementation will
give high resolution cputime accounting.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9485/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use txx9 up-counter for sched_clock source. This implementation will give
high resolution cputime accounting.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9484/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use ip27 hub real time counter for sched_clock source. This implementation
will give high resolution cputime accounting.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9483/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use DEC I/O ASIC's free-running counter for sched_clock source. This
implementation will give high resolution cputime accounting.
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9482/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is to make checkpatch.pl happy for the next patch. It would otherwise
say --

ERROR: Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already includes
a copy of the GPL.
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9481/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use the ZBbus cycle counter for sched_clock source. This implementation
will give high resolution cputime accounting.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9480/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is to make checkpatch.pl happy for the next patch. It would otherwise
say --

ERROR: Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already includes
a copy of the GPL.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9479/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use c0 count register for sched_clock source. This implementation will give
high resolution cputime accounting.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9478/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This will provide sched_clock interface to implement individual
read_sched_clock(). Not for CAVIUM_OCTEON_SOC as it defines its own
sched_clock() directly (not using the sched_clock_register interface).
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9477/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

GENERIC_SCHED_CLOCK can be selected by architectures other than ARM. The
current dependencies of CLKSRC_VERSATILE make it possible that other
architectures will have CLKSRC_VERSATILE available in configuration once
they select GENERIC_SCHED_CLOCK, whereas this clock source should be solely
available to ARM in reality.

This patch adds one more dependency to CLKSRC_VERSATILE to fix the issue.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Reported-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9476/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

With the correct cmpxchg64 on 32-bit platforms, we can now add the config
HAVE_VIRT_CPU_ACCOUNTING_GEN into arch/mips/Kconfig.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9475/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>