Might help one figure out why aqm drivers may fail to transmit
frames sometimes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This commit allows SAE Authentication for NL80211_CMD_CONNECT
interface, provided host driver advertises the support.

Host drivers may offload the SAE authentication to user space
through NL80211_CMD_EXTERNAL_AUTH interface and thus expect
the user space to advertise support to handle offload through
NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in NL80211_CMD_CONNECT
request. Such drivers should reject the connect request on no
offload support from user space.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This interface allows the host driver to offload the authentication to
user space. This is exclusively defined for host drivers that do not
define separate commands for authentication and association, but rely on
userspace SME (e.g., in wpa_supplicant for the ~WPA_DRIVER_FLAGS_SME
case) for the authentication to happen. This can be used to implement
SAE without full implementation in the kernel/firmware while still being
able to use NL80211_CMD_CONNECT with driver-based BSS selection.

Host driver sends NL80211_CMD_EXTERNAL_AUTH event to start/abort
authentication to the port on which connect is triggered and status
of authentication is further indicated by user space to host
driver through the same command response interface.

User space entities advertise this capability through the
NL80211_ATTR_EXTERNAL_AUTH_SUPP flag in the NL80211_CMD_CONNECT request.
Host drivers shall look at this capability to offload the authentication.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add socket connection ownership check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This commit defines new scan flags (LOW_SPAN, LOW_POWER, HIGH_LATENCY)
to emphasize the requested scan behavior for the driver. These flags
are optional and are mutually exclusive. The implementation of the
respective functionality can be driver/hardware specific.

These flags can be used to control the compromise between how long
a scan takes, how much power it uses, and high accurate/complete
the scan is in finding the BSSs.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make the dump operation aware of changes on radio list and corresponding
inconsistent dumps. Changed variable name for better understanding.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[compress ternary operator]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a NL_ERR_MSG in case of creating a radio by a netlink message to give
clear output to the creating process instead of creating only a debug
message in kernel log. The same function is used for the creation while
module load, so keep the old message, although it should never be thrown
while load, because the module controls all mac addresses.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[remove message, add missing braces]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If simulation needs predictable permanent mac addresses of hwsim wireless
phy, this patch add the ability to create a new radio with a user defined
permanent mac address. Allowed mac addresses needs to be locally
administrated mac addresses (as also the former fixed 42:* and 02:* were).

To do not break the operation with legacy software using hwsim, the new
address is set twice. The problem here is, the netlink call backs use
wiphy->addresses[1] as identification of a radio and not the proposed
permanent address (wiphy->addresses[0]). This design decision is not
documented in the kernel repo, therefore this patch simply reproduces this,
but with the same address.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[make pointer const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ipmr_vif_seq_show() prints the difference between two pointers with the
format string %2zd (z for size_t), however the correct format string is
%2td instead (t for ptrdiff_t).

The same bug in ip6mr_vif_seq_show() was already fixed long ago by
commit d430a227 ("bogus format in ip6mr").
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Wait for a response from the VNIC server before exiting after setting
the MAC address. The resolves an issue with bonding a VNIC client in
ALB or TLB modes. The bonding driver was changing the MAC address more
rapidly than the device could respond, causing the following errors.

"bond0: the hw address of slave eth2 is in use by the bond;
couldn't find a slave with a free hw address to give it
(this should not have happened)"

If the function waits until the change is finalized, these errors are
avoided.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following soft lockup was caught. This is a deadlock caused by
recusive locking.

Process kworker/u40:1:28016 was holding spin lock "mbx->queue_lock" in
qlcnic_83xx_mailbox_worker(), while a softirq came in and ask the same spin
lock in qlcnic_83xx_enqueue_mbx_cmd(). This lock should be hold by disable
bh..

[161846.962125] NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [kworker/u40:1:28016]
[161846.962367] Modules linked in: tun ocfs2 xen_netback xen_blkback xen_gntalloc xen_gntdev xen_evtchn xenfs xen_privcmd autofs4 ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs bnx2fc fcoe libfcoe libfc sunrpc 8021q mrp garp bridge stp llc bonding dm_round_robin dm_multipath iTCO_wdt iTCO_vendor_support pcspkr sb_edac edac_core i2c_i801 shpchp lpc_ich mfd_core ioatdma ipmi_devintf ipmi_si ipmi_msghandler sg ext4 jbd2 mbcache2 sr_mod cdrom sd_mod igb i2c_algo_bit i2c_core ahci libahci megaraid_sas ixgbe dca ptp pps_core vxlan udp_tunnel ip6_udp_tunnel qla2xxx scsi_transport_fc qlcnic crc32c_intel be2iscsi bnx2i cnic uio cxgb4i cxgb4 cxgb3i libcxgbi ipv6 cxgb3 mdio libiscsi_tcp qla4xxx iscsi_boot_sysfs libiscsi scsi_transport_iscsi dm_mirror dm_region_hash dm_log dm_mod
[161846.962454]
[161846.962460] CPU: 1 PID: 28016 Comm: kworker/u40:1 Not tainted 4.1.12-94.5.9.el6uek.x86_64 #2
[161846.962463] Hardware name: Oracle Corporation SUN SERVER X4-2L      /ASSY,MB,X4-2L         , BIOS 26050100 09/19/2017
[161846.962489] Workqueue: qlcnic_mailbox qlcnic_83xx_mailbox_worker [qlcnic]
[161846.962493] task: ffff8801f2e34600 ti: ffff88004ca5c000 task.ti: ffff88004ca5c000
[161846.962496] RIP: e030:[<ffffffff810013aa>]  [<ffffffff810013aa>] xen_hypercall_sched_op+0xa/0x20
[161846.962506] RSP: e02b:ffff880202e43388  EFLAGS: 00000206
[161846.962509] RAX: 0000000000000000 RBX: ffff8801f6996b70 RCX: ffffffff810013aa
[161846.962511] RDX: ffff880202e433cc RSI: ffff880202e433b0 RDI: 0000000000000003
[161846.962513] RBP: ffff880202e433d0 R08: 0000000000000000 R09: ffff8801fe893200
[161846.962516] R10: ffff8801fe400538 R11: 0000000000000206 R12: ffff880202e4b000
[161846.962518] R13: 0000000000000050 R14: 0000000000000001 R15: 000000000000020d
[161846.962528] FS:  0000000000000000(0000) GS:ffff880202e40000(0000) knlGS:ffff880202e40000
[161846.962531] CS:  e033 DS: 0000 ES: 0000 CR0: 0000000080050033
[161846.962533] CR2: 0000000002612640 CR3: 00000001bb796000 CR4: 0000000000042660
[161846.962536] Stack:
[161846.962538]  ffff880202e43608 0000000000000000 ffffffff813f0442 ffff880202e433b0
[161846.962543]  0000000000000000 ffff880202e433cc ffffffff00000001 0000000000000000
[161846.962547]  00000009813f03d6 ffff880202e433e0 ffffffff813f0460 ffff880202e43440
[161846.962552] Call Trace:
[161846.962555]  <IRQ>
[161846.962565]  [<ffffffff813f0442>] ? xen_poll_irq_timeout+0x42/0x50
[161846.962570]  [<ffffffff813f0460>] xen_poll_irq+0x10/0x20
[161846.962578]  [<ffffffff81014222>] xen_lock_spinning+0xe2/0x110
[161846.962583]  [<ffffffff81013f01>] __raw_callee_save_xen_lock_spinning+0x11/0x20
[161846.962592]  [<ffffffff816e5c57>] ? _raw_spin_lock+0x57/0x80
[161846.962609]  [<ffffffffa028acfc>] qlcnic_83xx_enqueue_mbx_cmd+0x7c/0xe0 [qlcnic]
[161846.962623]  [<ffffffffa028e008>] qlcnic_83xx_issue_cmd+0x58/0x210 [qlcnic]
[161846.962636]  [<ffffffffa028caf2>] qlcnic_83xx_sre_macaddr_change+0x162/0x1d0 [qlcnic]
[161846.962649]  [<ffffffffa028cb8b>] qlcnic_83xx_change_l2_filter+0x2b/0x30 [qlcnic]
[161846.962657]  [<ffffffff8160248b>] ? __skb_flow_dissect+0x18b/0x650
[161846.962670]  [<ffffffffa02856e5>] qlcnic_send_filter+0x205/0x250 [qlcnic]
[161846.962682]  [<ffffffffa0285c77>] qlcnic_xmit_frame+0x547/0x7b0 [qlcnic]
[161846.962691]  [<ffffffff8160ac22>] xmit_one+0x82/0x1a0
[161846.962696]  [<ffffffff8160ad90>] dev_hard_start_xmit+0x50/0xa0
[161846.962701]  [<ffffffff81630112>] sch_direct_xmit+0x112/0x220
[161846.962706]  [<ffffffff8160b80f>] __dev_queue_xmit+0x1df/0x5e0
[161846.962710]  [<ffffffff8160bc33>] dev_queue_xmit_sk+0x13/0x20
[161846.962721]  [<ffffffffa0575bd5>] bond_dev_queue_xmit+0x35/0x80 [bonding]
[161846.962729]  [<ffffffffa05769fb>] __bond_start_xmit+0x1cb/0x210 [bonding]
[161846.962736]  [<ffffffffa0576a71>] bond_start_xmit+0x31/0x60 [bonding]
[161846.962740]  [<ffffffff8160ac22>] xmit_one+0x82/0x1a0
[161846.962745]  [<ffffffff8160ad90>] dev_hard_start_xmit+0x50/0xa0
[161846.962749]  [<ffffffff8160bb1e>] __dev_queue_xmit+0x4ee/0x5e0
[161846.962754]  [<ffffffff8160bc33>] dev_queue_xmit_sk+0x13/0x20
[161846.962760]  [<ffffffffa05cfa72>] vlan_dev_hard_start_xmit+0xb2/0x150 [8021q]
[161846.962764]  [<ffffffff8160ac22>] xmit_one+0x82/0x1a0
[161846.962769]  [<ffffffff8160ad90>] dev_hard_start_xmit+0x50/0xa0
[161846.962773]  [<ffffffff8160bb1e>] __dev_queue_xmit+0x4ee/0x5e0
[161846.962777]  [<ffffffff8160bc33>] dev_queue_xmit_sk+0x13/0x20
[161846.962789]  [<ffffffffa05adf74>] br_dev_queue_push_xmit+0x54/0xa0 [bridge]
[161846.962797]  [<ffffffffa05ae4ff>] br_forward_finish+0x2f/0x90 [bridge]
[161846.962807]  [<ffffffff810b0dad>] ? ttwu_do_wakeup+0x1d/0x100
[161846.962811]  [<ffffffff815f929b>] ? __alloc_skb+0x8b/0x1f0
[161846.962818]  [<ffffffffa05ae04d>] __br_forward+0x8d/0x120 [bridge]
[161846.962822]  [<ffffffff815f613b>] ? __kmalloc_reserve+0x3b/0xa0
[161846.962829]  [<ffffffff810be55e>] ? update_rq_runnable_avg+0xee/0x230
[161846.962836]  [<ffffffffa05ae176>] br_forward+0x96/0xb0 [bridge]
[161846.962845]  [<ffffffffa05af85e>] br_handle_frame_finish+0x1ae/0x420 [bridge]
[161846.962853]  [<ffffffffa05afc4f>] br_handle_frame+0x17f/0x260 [bridge]
[161846.962862]  [<ffffffffa05afad0>] ? br_handle_frame_finish+0x420/0x420 [bridge]
[161846.962867]  [<ffffffff8160d057>] __netif_receive_skb_core+0x1f7/0x870
[161846.962872]  [<ffffffff8160d6f2>] __netif_receive_skb+0x22/0x70
[161846.962877]  [<ffffffff8160d913>] netif_receive_skb_internal+0x23/0x90
[161846.962884]  [<ffffffffa07512ea>] ? xenvif_idx_release+0xea/0x100 [xen_netback]
[161846.962889]  [<ffffffff816e5a10>] ? _raw_spin_unlock_irqrestore+0x20/0x50
[161846.962893]  [<ffffffff8160e624>] netif_receive_skb_sk+0x24/0x90
[161846.962899]  [<ffffffffa075269a>] xenvif_tx_submit+0x2ca/0x3f0 [xen_netback]
[161846.962906]  [<ffffffffa0753f0c>] xenvif_tx_action+0x9c/0xd0 [xen_netback]
[161846.962915]  [<ffffffffa07567f5>] xenvif_poll+0x35/0x70 [xen_netback]
[161846.962920]  [<ffffffff8160e01b>] napi_poll+0xcb/0x1e0
[161846.962925]  [<ffffffff8160e1c0>] net_rx_action+0x90/0x1c0
[161846.962931]  [<ffffffff8108aaba>] __do_softirq+0x10a/0x350
[161846.962938]  [<ffffffff8108ae75>] irq_exit+0x125/0x130
[161846.962943]  [<ffffffff813f03a9>] xen_evtchn_do_upcall+0x39/0x50
[161846.962950]  [<ffffffff816e7ffe>] xen_do_hypervisor_callback+0x1e/0x40
[161846.962952]  <EOI>
[161846.962959]  [<ffffffff816e5c4a>] ? _raw_spin_lock+0x4a/0x80
[161846.962964]  [<ffffffff816e5b1e>] ? _raw_spin_lock_irqsave+0x1e/0xa0
[161846.962978]  [<ffffffffa028e279>] ? qlcnic_83xx_mailbox_worker+0xb9/0x2a0 [qlcnic]
[161846.962991]  [<ffffffff810a14e1>] ? process_one_work+0x151/0x4b0
[161846.962995]  [<ffffffff8100c3f2>] ? check_events+0x12/0x20
[161846.963001]  [<ffffffff810a1960>] ? worker_thread+0x120/0x480
[161846.963005]  [<ffffffff816e187b>] ? __schedule+0x30b/0x890
[161846.963010]  [<ffffffff810a1840>] ? process_one_work+0x4b0/0x4b0
[161846.963015]  [<ffffffff810a1840>] ? process_one_work+0x4b0/0x4b0
[161846.963021]  [<ffffffff810a6b3e>] ? kthread+0xce/0xf0
[161846.963025]  [<ffffffff810a6a70>] ? kthread_freezable_should_stop+0x70/0x70
[161846.963031]  [<ffffffff816e6522>] ? ret_from_fork+0x42/0x70
[161846.963035]  [<ffffffff810a6a70>] ? kthread_freezable_should_stop+0x70/0x70
[161846.963037] Code: cc 51 41 53 b8 1c 00 00 00 0f 05 41 5b 59 c3 cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 51 41 53 b8 1d 00 00 00 0f 05 <41> 5b 59 c3 cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

socket can be disconnected and gets transformed back to a listening
socket, if sk_frag.page is not released, which will be cloned into
a new socket by sk_clone_lock, but the reference count of this page
is increased, lead to a use after free or double free issue
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using ioctl to get address of interface, we can't
get it anymore. For example, the command is show as below.

	# ifconfig eth0

In the patch ("03aef17b"), the devinet_ioctl does not
return a suitable value, even though we can find it in
the kernel. Then fix it now.

Fixes: 03aef17b ("devinet_ioctl(): take copyin/copyout to caller")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported a lockdep splat in gen_new_estimator() /
est_fetch_counters() when attempting to lock est->stats_lock.

Since est_fetch_counters() is called from BH context from timer
interrupt, we need to block BH as well when calling it from process
context.

Most qdiscs use per cpu counters and are immune to the problem,
but net/sched/act_api.c and net/netfilter/xt_RATEEST.c are using
a spinlock to protect their data. They both call gen_new_estimator()
while object is created and not yet alive, so this bug could
not trigger a deadlock, only a lockdep splat.

Fixes: 1c0d32fd ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On TTC table creation, the indirection TIRs should be used instead of
the inner indirection TIRs.

Fixes: 1ae1df3a ("net/mlx5e: Refactor RSS related objects and code")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner reported a lockdep splat [1]

This is caused by attempting GFP_KERNEL allocation while RCU lock is
held and BH blocked.

We believe that addrconf_verify_rtnl() could run for a long period,
so instead of using GFP_ATOMIC here as Ido suggested, we should break
the critical section and restart it after the allocation.

[1]
[86220.125562] =============================
[86220.125586] WARNING: suspicious RCU usage
[86220.125612] 4.15.0-rc7-next-20180110+ #7 Not tainted
[86220.125641] -----------------------------
[86220.125666] kernel/sched/core.c:6026 Illegal context switch in RCU-bh read-side critical section!
[86220.125711]
               other info that might help us debug this:

[86220.125755]
               rcu_scheduler_active = 2, debug_locks = 1
[86220.125792] 4 locks held by kworker/0:2/1003:
[86220.125817]  #0:  ((wq_completion)"%s"("ipv6_addrconf")){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680
[86220.125895]  #1:  ((addr_chk_work).work){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680
[86220.125959]  #2:  (rtnl_mutex){+.+.}, at: [<00000000b06d9510>] rtnl_lock+0x12/0x20
[86220.126017]  #3:  (rcu_read_lock_bh){....}, at: [<00000000aef52299>] addrconf_verify_rtnl+0x1e/0x510 [ipv6]
[86220.126111]
               stack backtrace:
[86220.126142] CPU: 0 PID: 1003 Comm: kworker/0:2 Not tainted 4.15.0-rc7-next-20180110+ #7
[86220.126185] Hardware name: ZOTAC ZBOX-CI321NANO/ZBOX-CI321NANO, BIOS B246P105 06/01/2015
[86220.126250] Workqueue: ipv6_addrconf addrconf_verify_work [ipv6]
[86220.126288] Call Trace:
[86220.126312]  dump_stack+0x70/0x9e
[86220.126337]  lockdep_rcu_suspicious+0xce/0xf0
[86220.126365]  ___might_sleep+0x1d3/0x240
[86220.126390]  __might_sleep+0x45/0x80
[86220.126416]  kmem_cache_alloc_trace+0x53/0x250
[86220.126458]  ? ipv6_add_addr+0xfe/0x6e0 [ipv6]
[86220.126498]  ipv6_add_addr+0xfe/0x6e0 [ipv6]
[86220.126538]  ipv6_create_tempaddr+0x24d/0x430 [ipv6]
[86220.126580]  ? ipv6_create_tempaddr+0x24d/0x430 [ipv6]
[86220.126623]  addrconf_verify_rtnl+0x339/0x510 [ipv6]
[86220.126664]  ? addrconf_verify_rtnl+0x339/0x510 [ipv6]
[86220.126708]  addrconf_verify_work+0xe/0x20 [ipv6]
[86220.126738]  process_one_work+0x258/0x680
[86220.126765]  worker_thread+0x35/0x3f0
[86220.126790]  kthread+0x124/0x140
[86220.126813]  ? process_one_work+0x680/0x680
[86220.126839]  ? kthread_create_worker_on_cpu+0x40/0x40
[86220.126869]  ? umh_complete+0x40/0x40
[86220.126893]  ? call_usermodehelper_exec_async+0x12a/0x160
[86220.126926]  ret_from_fork+0x4b/0x60
[86220.126999] BUG: sleeping function called from invalid context at mm/slab.h:420
[86220.127041] in_atomic(): 1, irqs_disabled(): 0, pid: 1003, name: kworker/0:2
[86220.127082] 4 locks held by kworker/0:2/1003:
[86220.127107]  #0:  ((wq_completion)"%s"("ipv6_addrconf")){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680
[86220.127179]  #1:  ((addr_chk_work).work){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680
[86220.127242]  #2:  (rtnl_mutex){+.+.}, at: [<00000000b06d9510>] rtnl_lock+0x12/0x20
[86220.127300]  #3:  (rcu_read_lock_bh){....}, at: [<00000000aef52299>] addrconf_verify_rtnl+0x1e/0x510 [ipv6]
[86220.127414] CPU: 0 PID: 1003 Comm: kworker/0:2 Not tainted 4.15.0-rc7-next-20180110+ #7
[86220.127463] Hardware name: ZOTAC ZBOX-CI321NANO/ZBOX-CI321NANO, BIOS B246P105 06/01/2015
[86220.127528] Workqueue: ipv6_addrconf addrconf_verify_work [ipv6]
[86220.127568] Call Trace:
[86220.127591]  dump_stack+0x70/0x9e
[86220.127616]  ___might_sleep+0x14d/0x240
[86220.127644]  __might_sleep+0x45/0x80
[86220.127672]  kmem_cache_alloc_trace+0x53/0x250
[86220.127717]  ? ipv6_add_addr+0xfe/0x6e0 [ipv6]
[86220.127762]  ipv6_add_addr+0xfe/0x6e0 [ipv6]
[86220.127807]  ipv6_create_tempaddr+0x24d/0x430 [ipv6]
[86220.127854]  ? ipv6_create_tempaddr+0x24d/0x430 [ipv6]
[86220.127903]  addrconf_verify_rtnl+0x339/0x510 [ipv6]
[86220.127950]  ? addrconf_verify_rtnl+0x339/0x510 [ipv6]
[86220.127998]  addrconf_verify_work+0xe/0x20 [ipv6]
[86220.128032]  process_one_work+0x258/0x680
[86220.128063]  worker_thread+0x35/0x3f0
[86220.128091]  kthread+0x124/0x140
[86220.128117]  ? process_one_work+0x680/0x680
[86220.128146]  ? kthread_create_worker_on_cpu+0x40/0x40
[86220.128180]  ? umh_complete+0x40/0x40
[86220.128207]  ? call_usermodehelper_exec_async+0x12a/0x160
[86220.128243]  ret_from_fork+0x4b/0x60

Fixes: f3d9832e ("ipv6: addrconf: cleanup locking in ipv6_add_addr")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In current route cache aging logic, if a route has both RTF_EXPIRE and
RTF_GATEWAY set, the route will only be removed if the neighbor cache
has no NTF_ROUTER flag. Otherwise, even if the route has expired, it
won't get deleted.
Fix this logic to always check if the route has expired first and then
do the gateway neighbor cache check if previous check decide to not
remove the exception entry.

Fixes: 1859bac0 ("ipv6: remove from fib tree aged out RTF_CACHE dst")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compared to ixgbe and other previous Intel drivers the i40e and i40evf
drivers actually reserve 2 additional descriptors in maybe_stop_tx for
cache line alignment. We need to update DESC_NEEDED to reflect this as
otherwise we are more likely to return TX_BUSY which will cause issues with
things like xmit_more.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to cancel any pending work that might update driver coalesce
settings when taking down an interface.

Fixes: 6a8788f2 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unsolicited IPv6 neighbor advertisements should be sent after DAD
completes. Update ndisc_send_unsol_na to skip tentative, non-optimistic
addresses and have those sent by addrconf_dad_completed after DAD.

Fixes: 4a6e3c5d ("net: ipv6: send unsolicited NA on admin up")
Reported-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.

For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:

  'skb->len == 1600' from the first fragment

  size  = lstatus & BD_LENGTH_MASK; # 1602
  size -= ETH_FCS_LEN;              # 1598
  size -= skb->len;                 # -2

Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:

  kernel BUG at ./include/linux/skbuff.h:2068!
  Oops: Exception in kernel mode, sig: 5 [#1]
  ...
  NIP [c021ec60] skb_pull+0x24/0x44
  LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690
  Call Trace:
  [df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
  [df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
  [df7edf40] [c023352c] net_rx_action+0x21c/0x274
  [df7edf90] [c0329000] __do_softirq+0xd8/0x240
  [df7edff0] [c000c108] call_do_irq+0x24/0x3c
  [c0597e90] [c00041dc] do_IRQ+0x64/0xc4
  [c0597eb0] [c000d920] ret_from_except+0x0/0x18
  --- interrupt: 501 at arch_cpu_idle+0x24/0x5c

Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.

Fixes: 6c389fc9 ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong Wang says:

====================
net_sched: reflect tx_queue_len change for pfifo_fast

This pathcset restores the pfifo_fast qdisc behavior of dropping
packets based on latest dev->tx_queue_len. Patch 1 introduces
a helper, patch 2 introduces a new Qdisc ops which is called when
we modify tx_queue_len, patch 3 implements this ops for pfifo_fast.

Please see each patch for details.

---
v3: use skb_array_resize_multiple()
v2: handle error case for ->change_tx_queue_len()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

pfifo_fast used to drop based on qdisc_dev(qdisc)->tx_queue_len,
so we have to resize skb array when we change tx_queue_len.

Other qdiscs which read tx_queue_len are fine because they
all save it to sch->limit or somewhere else in qdisc during init.
They don't have to implement this, it is nicer if they do so
that users don't have to re-configure qdisc after changing
tx_queue_len.

Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new qdisc ops ->change_tx_queue_len() so that
each qdisc could decide how to implement this if it wants.
Previously we simply read dev->tx_queue_len, after pfifo_fast
switches to skb array, we need this API to resize the skb array
when we change dev->tx_queue_len.

To avoid handling race conditions with TX BH, we need to
deactivate all TX queues before change the value and bring them
back after we are done, this also makes implementation easier.

Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch promotes the local change_tx_queue_len() to a core
helper function, dev_change_tx_queue_len(), so that rtnetlink
and net-sysfs could share the code. This also prepares for the
following patch.

Note, the -EFAULT in the original code doesn't make sense,
we should propagate the errno from notifiers.

Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't stop device before reset owner, this means we could try to
serve any virtqueue kick before reset dev->worker. This will result a
warn since the work was pending at llist during owner resetting. Fix
this by stopping device during owner reset.

Reported-by: syzbot+eb17c6162478cc50632c@syzkaller.appspotmail.com
Fixes: 3a4d5c94 ("vhost_net: a kernel-level virtio server")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nicolas Dichtel says:

====================
net: Ease to follow an interface that moves to another netns

The goal of this series is to ease the user to follow an interface that
moves to another netns.

After this series, with a patched iproute2:

$ ip netns
bar
foo
$ ip monitor link &
$ ip link set dummy0 netns foo
Deleted 5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default
    link/ether 6e:a7:82:35:96:46 brd ff:ff:ff:ff:ff:ff new-nsid 0 new-ifindex 6

=> new nsid: 0, new ifindex: 6 (was 5 in the previous netns)

$ ip link set eth1 netns bar
Deleted 3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
    link/ether 52:54:01:12:34:57 brd ff:ff:ff:ff:ff:ff new-nsid 1 new-ifindex 3

=> new nsid: 1, new ifindex: 3 (same ifindex)

$ ip netns
bar (id: 1)
foo (id: 0)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal is to let the user follow an interface that moves to another
netns.

CC: Jiri Benc <jbenc@redhat.com>
CC: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The user should be able to follow any interface that moves to another
netns.  There is no reason to hide physical interfaces.

CC: Jiri Benc <jbenc@redhat.com>
CC: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was found that ethtool provides unexisting module name while
it queries the specified network device for associated driver
information. Then user tries to unload that module by provided
module name and fails.

This happens because ethtool reads value of DRV_NAME macro,
while module name is defined at the driver's Makefile.

This patch is to correct Cavium CN88xx Thunder NIC driver names
(DRV_NAME macro) 'thunder-nicvf' to 'nicvf' and 'thunder-nic'
to 'nicpf', sync bgx and xcv driver names accordingly to their
module names.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael S. Tsirkin says:

====================
ptr_ring fixes

This fixes a bunch of issues around ptr_ring use in net core.
One of these: "tap: fix use-after-free" is also needed on net,
but can't be backported cleanly.

I will post a net patch separately.

Lightly tested - Jason, could you pls confirm this
addresses the security issue you saw with ptr_ring?
Testing reports would be appreciated too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Offset 128 overlaps the last word of the redzone.
Use 132 which is always beyond that.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to make ptr_ring test build again.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't rely on lockless guarantees, but it
seems cleaner than inverting __ptr_ring_peek.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In theory compiler could tear queue loads or stores in two. It does not
seem to be happening in practice but it seems easier to convert the
cases where this would be a problem to READ/WRITE_ONCE than worry about
it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__skb_array_empty should use __ptr_ring_empty since that's the only
legal lockless function.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit bcecb4bb.

If we try to allocate an extra entry as the above commit did, and when
the requested size is UINT_MAX, addition overflows causing zero size to
be passed to kmalloc().

kmalloc then returns ZERO_SIZE_PTR with a subsequent crash.

Reported-by: syzbot+87678bcf753b44c39b67@syzkaller.appspotmail.com
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to bcecb4bb ("net: ptr_ring: otherwise safe empty checks can
overrun array bounds") a lockless use of __ptr_ring_full might
cause an out of bounds access.

We can fix this, but it's easier to just disallow lockless
__ptr_ring_full for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lockless access to __ptr_ring_full is only legal if ring is
never resized, otherwise it might cause use-after free errors.
Simply drop the lockless test, we'll drop the packet
a bit later when produce fails.

Fixes: 362899b8 ("macvtap: switch to use skb array")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>