- 11 Mar, 2011 9 commits
-
-
Johannes Berg authored
Add support to iwlagn for off-channel TX. The microcode API for this is a bit strange in that it uses a hacked-up scan command, so the scan code needs to change quite a bit to accomodate that and be able to send it out. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Jason Young authored
If dynamic_ps is disabled, enabling power save before the 4-way handshake completes may delay the station from being authorized to send/receive traffic, i.e. increase roaming times. It also may result in a failed 4-way handshake depending on the AP's timing requirements and beacon interval, and the station's listen interval. To fix this, prevent power save from being enabled while the station isn't authorized and recalculate power save whenever the station's authorized state changes. Signed-off-by:
Jason Young <a.young.jason@gmail.com> Acked-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Dan Carpenter authored
defs.meshie.val.mesh_id is 32 chars long. It's not supposed to be NUL terminated. This code puts a terminator on the end to make it easier to print to sysfs. The problem is that if the mesh_id fills the entire buffer the original code puts the terminator one spot past the end. The way the original code was written, there was a check to make sure that maxlen was less than PAGE_SIZE. Since we know that maxlen is at most 34 chars, I just removed the check. Signed-off-by:
Dan Carpenter <error27@gmail.com> Acked-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Vivek Natarajan authored
Increasing the wait count makes the nf load pass in most of the cases. Signed-off-by:
Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by:
-
Vivek Natarajan authored
Increase the delay to make sure the initialization of pll passes. Signed-off-by:
-
Vivek Natarajan authored
Set some GPIO pins to Pull-down mode to save power. Signed-off-by:
-
Felix Fietkau authored
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad and covers even frames with PHY errors. When this flag is enabled, this message shows up frequently during scanning or hardware resets: ath: Could not stop RX, we could be confusing the DMA engine when we start RX up Since promiscuous mode is usually not particularly useful, yet enabled by default by bridging (either used normally in 4-addr mode, or with hacks for various virtualization software), we should sacrifice it for better reliability during normal operation. This patch leaves it enabled if there are active monitor mode interfaces, since it's very useful for debugging. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by:
-
Grazvydas Ignotas authored
While working on PS I've noticed elp_work is kicking rather often, and sometimes the chip is put to sleep before 5ms delay expires. This seems to happen because by the time wl1251_ps_elp_wakeup is called elp_work might still be pending. After wakeup is done, the processing may take some time, during which 5ms might expire and elp_work might get scheduled. In this case, ss soon as 1st thread finishes work and releases the mutex, elp_work will then put the device to sleep without 5ms delay. In addition 1st thread will queue additional elp_work needlessly. Fix this by cancelling work in wl1251_ps_elp_wakeup instead. Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Acked-by:
Kalle Valo <kvalo@adurom.com> Signed-off-by:
-
Grazvydas Ignotas authored
wl1251_ps_set_elp() only does acx_sleep_auth call and takes the chip from/to ELP, however all callers of wl1251_ps_set_mode() have already taken the chip out of ELP and puts it back to ELP when they finish. This makes ELP calls (and register writes they result in) superfluous. So remove wl1251_ps_set_elp function and call acx_sleep_auth directly. Signed-off-by:
-
- 09 Mar, 2011 5 commits
-
-
Daniel Halperin authored
Waiting until the status is received can cause the same rate to be probed multiple times consecutively. Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by:
-
John W. Linville authored
This just matches reality... Signed-off-by:
Bob Copeland <me@bobcopeland.com>
-
Scott James Remnant authored
Regulatory devices issue change uevents to inform userspace of a need to call the crda tool; however these can often be sent before udevd is running, and were not previously included in the results of udevadm trigger (which requests a new change event using the /uevent attribute of the sysfs object). Add a uevent function to the device type which includes the COUNTRY information from the last request if it has yet to be processed, the case of multiple requests is already handled in the code by checking whether an unprocessed one is queued in the same manner and refusing to queue a new one. The existing udev rule continues to work as before. Signed-off-by:
Scott James Remnant <keybuk@google.com> Acked-By:
Kay Sievers <kay.sievers@vrfy.org> Acked-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Bing Zhao authored
and make use of it in wireless drivers Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Shan Wei authored
Use kcalloc or kzalloc rather than the combination of kmalloc and memset. Thanks coccicheck for detecting this. (http://coccinelle.lip6.fr/) Signed-off-by:
Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by:
-
- 07 Mar, 2011 8 commits
-
-
Johannes Berg authored
The scan code has a race that Michael reported he ran into, but it's easy to fix while at the same time simplifying the code. The race resulted in the following warning: ------------[ cut here ]------------ WARNING: at net/mac80211/scan.c:310 ieee80211_rx_bss_free+0x20c/0x4b8 [mac80211]() Modules linked in: [...] [<c0033edc>] (unwind_backtrace+0x0/0xe0) from [<c004f2a4>] (warn_slowpath_common+0x4c/0x64) [... backtrace wasn't useful ...] Reported-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Michael Buesch authored
This updates the p54spi Kconfig help text. The driver works well on n8x0, so remove the words "experimental" and "untested". Signed-off-by:
-
Michael Buesch authored
Add a log message to ieee80211_restart_hw() to highlight that special codepath in the logs. This helps debugging bugs in the rarely tested restart code. Signed-off-by:
-
Stanislaw Gruszka authored
My commit 466a19a0 "iwlwifi: move rx handlers code to iwl-rx.c" breaks compilation on 32 bits. Fix that. Reported-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Shan Wei authored
Signed-off-by:
-
Shan Wei authored
Compile test only. Signed-off-by:
-
Ben Greear authored
It seems ath5k has issues receiving broadcast packets (ARPs) when using multiple STA interfaces associated with multiple APs. This patch ensures the NIC is always in PROMISC mode if there are more than 1 stations associated. Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
- 04 Mar, 2011 18 commits
-
-
Stanislaw Gruszka authored
Usually H/W generate statistics notify once per about 100ms, but sometimes we can receive notify in shorter time, even 2 ms. This can be problem for plcp health and ack health checking. I.e. with 2 plcp errors happens randomly in 2 ms duration, we exceed plcp delta threshold equal to 100 (2*100/2). Also checking ack's in short time, can results not necessary false positive and firmware reset, for example when channel is noised and we do not receive ACKs frames or when remote device does not send ACKs at the moment. Patch change code to do statistic check and possible recovery only if 99ms elapsed from last check. Forced delay should assure we have good statistic data to estimate hardware state. Signed-off-by:
-
Stanislaw Gruszka authored
Make iwl_good_plcp_health code easiest to read. Signed-off-by:
-
Stanislaw Gruszka authored
Put generic rx_handlers (except iwlagn_rx_reply_compressed_ba) to iwl-rx.c . Make functions static and change prefix from iwlagn_ to iwl_ . Beautify iwl_setup_rx_handlers and do some other minor coding style changes. Signed-off-by:
-
Helmut Schaa authored
mac80211 does the same afterwards anyway. Hence, just drop this redundant code. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
-
Ben Greear authored
No use printing addresses of pointers, just print the pointers themselves. Signed-off-by:
-
Gertjan van Wingerde authored
Now that all accesses to the data_queue structures is done via the specialized rt2x00queue_get_tx_queue function or via direct accesses, there is no need for the rt2x00queue_get_queue function anymore, so remove it. Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Gertjan van Wingerde authored
In the spirit of optimizing the code to get the queue structure of TX queues, also optimize the code to get beacon queues. We can simply use the bcn queue field of the rt2x00_dev structure instead of using the rt2x00queue_get_queue function. Signed-off-by:
-
Gertjan van Wingerde authored
The ATIM queue is considered to be a TX queue by the drivers that support the queue. Therefore include support for the ATIM queue to the rt2x00queue_get_tx_queue function so that the drivers that support the ATIM queue can also use that function. Add the support in such a way that drivers that do not support the ATIM queue are not penalized in their efficiency. Signed-off-by:
-
Gertjan van Wingerde authored
Current code for the atim queue is strange, as it is considered in the rt2x00_dev structure as a second beacon queue. Normalize this by letting the atim queue have its own struct data_queue pointer in the rt2x00_dev structure. Signed-off-by:
-
Helmut Schaa authored
We don't use interrupt threads anymore. Fix the comment. Signed-off-by:
-
Helmut Schaa authored
The PCI device irqmask is locked by a spin_lock. Currently spin_lock_irqsave is used everywhere. To reduce the locking overhead replace spin_lock_irqsave in hard irq context with spin_lock and in soft irq context with spin_lock_irq. Signed-off-by:
-
Helmut Schaa authored
Signed-off-by:
-
Helmut Schaa authored
When setting up multiple BSSIDs in AP mode on an rt2800pci device we previously used the STAs AID to select an appropriate key slot. But since the AID is per VIF we can end up with two STAs having the same AID and thus using the same key index. This resulted in one STA overwriting the key information of another STA. Fix this by simply searching for the next unused entry in the pairwise key table. Also bring the key table init in sync with deleting keys by initializing the key table entries to 0 instead of 1. Signed-off-by:
-
Helmut Schaa authored
This makes the code less error-prone. Acked-by:
-
Helmut Schaa authored
ieee80211_get_tx_rate is not valid for HT rates. Hence, restructure the TX desciptor creation to be aware of MCS rates. The generic TX desciptor creation now cares about the rate_mode (CCK, OFDM, MCS, GF). As a result, ieee80211_get_tx_rate gets only called for legacy rates. Acked-by:
-
Helmut Schaa authored
"ifs" is only used by no-HT devices. Move it into the plcp substruct and fill in the value only for no-HT devices. Signed-off-by:
-
Ivo van Doorn authored
Some fields only need to be u8 and for ifs and txop we can use the already available enums. Acked-by:
-
Helmut Schaa authored
HT and no-HT rt2x00 devices use a partly different TX descriptor. Optimize the tx desciptor memory layout by putting the PLCP and HT substructs into a union and introduce a new driver flag to decide which TX desciptor format is used by the device. This saves us the expensive PLCP calculation fOr HT devices and the HT descriptor setup on no-HT devices. Acked-by:
-
