Pull pin control fixes from Linus Walleij:
 "Two pin control fixes arriving late, these are hopefully the last pin
  control fixes I send this kernel cycle. A Chromebook and an Exynos SoC
  thingie.

  The Exynos patch is pretty big, it is fixing unbroken a breakage
  caused by yours truly when trying to figure out the merge mess with
  the different Samsung platforms for this merge window. Sorry about
  that. We have countered this situation by assigning a Samsung pin
  control submaintainer to catch stuff earlier.

  Summary:

   - Make the Acer Chromebook keyboard work again with the Intel
     Cherryview driver.

   - Fix a merge error in the Exynos 5433 driver"

* tag 'pinctrl-v4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: cherryview: Add a quirk to make Acer Chromebook keyboard work again
  pinctrl: samsung: Add missing part for PINCFG_TYPE_DRV of Exynos5433

Pull drm fixes from Dave Airlie:
 "i915, gvt, nouveau, udl and etnaviv fixes.

  I was away the end of last week, so some of these would have been in
  rc6, and it's Easter from tomorrow, so I decided I better dequeue what
  I have now.

  The nouveau changes, just add a hw enable for GP107 display (like a
  pci id addition really), and fix a couple of regressions. i915 has
  some more gvt fixes, along with a few run of the mill ones, the rcu
  one seems like a few people have hit it.

  Otherwise a small udl and small etnaviv fix"

* tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
  drm/udl: Fix unaligned memory access in udl_render_hline
  drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
  drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
  drm/nouveau: initial support (display-only) for GP107
  drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
  drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
  drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
  drm/nouveau/mpeg: mthd returns true on success now
  drm/i915/gvt: set the correct default value of CTX STATUS PTR
  drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
  drm/i915: Use a dummy timeline name for a signaled fence
  drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
  drm/i915/gvt: remove the redundant info NULL check
  drm/i915/gvt: adjust mem size for low resolution type
  drm/i915: Avoid lock dropping between rescheduling
  drm/i915/gvt: exclude cfg space from failsafe mode
  drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
  drm/i915/execlists: Wrap tail pointer after reset tweaking
  drm/i915/perf: remove user triggerable warn
  ...

Merge tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fixes from Thierry Reding:
 "This contain a fix for the atomic update support recently added to
  the Rockchip driver where the clock reference count would become
  unbalanced and result in the clock feeding the PWM to always be
  disabled.

  Another fix to the Intel LPSS driver that adds an update bit quirk
  required for a specific configuration"

* tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: rockchip: State of PWM clock should synchronize with PWM enabled state
  pwm: lpss: Set enable-bit before waiting for update-bit to go low
  pwm: lpss: Split Tangier configuration

GP107 modesetting support (just recognising the chipset, no other changes until 4.12)
a couple of regression fixes, one of them a rather serious double-free issue that appeared in 4.10.
* 'linux-4.11' of git://github.com/skeggsb/linux:
  drm/nouveau: initial support (display-only) for GP107
  drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
  drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
  drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
  drm/nouveau/mpeg: mthd returns true on success now

Merge tag 'drm-intel-fixes-2017-04-12' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes

drm/i915 fixes for v4.11-rc7

one rcu related fix, and a few GVT fixes.

* tag 'drm-intel-fixes-2017-04-12' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
  drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
  drm/i915/gvt: set the correct default value of CTX STATUS PTR
  drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
  drm/i915: Use a dummy timeline name for a signaled fence
  drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
  drm/i915/gvt: remove the redundant info NULL check
  drm/i915/gvt: adjust mem size for low resolution type
  drm/i915: Avoid lock dropping between rescheduling
  drm/i915/gvt: exclude cfg space from failsafe mode
  drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
  drm/i915/execlists: Wrap tail pointer after reset tweaking
  drm/i915/perf: remove user triggerable warn
  drm/i915/perf: destroy stream on sample_flags mismatch
  drm/i915: Align "unfenced" tiled access on gen2, early gen3

drm-misc-fixes for 2017-04-11

Core changes:
 - None

Driver changes
 - udl: Fix unaligned memory access on SPARC (Jonathan)

* tag 'drm-misc-fixes-2017-04-11' of git://anongit.freedesktop.org/git/drm-misc:
  drm/udl: Fix unaligned memory access in udl_render_hline

Single etnaviv error path fix.

* 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux:
  drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()

Add the missing unlock before return from function etnaviv_gpu_submit()
in the error handling case.

lst: fixed label name.

Fixes: f3cd1b06 ("drm/etnaviv: (re-)protect fence allocation with
GPU mutex")
CC: stable@vger.kernel.org #4.9+
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

Pull audit fix from Paul Moore:
 "One more small audit fix, this should be the last for v4.11.

  Seth Forshee noticed a problem where the audit retry queue wasn't
  being flushed properly when audit was enabled and the audit daemon
  wasn't running; this patches fixes the problem (see the commit
  description for more details on the change).

  Both Seth and I have tested this and everything looks good"

* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
  audit: make sure we don't let the retry queue grow without bounds

Pull SCSI target fixes from Nicholas Bellinger:

 "There has been work in a number of different areas over the last
  weeks, including:

   - Fix target-core-user (TCMU) back-end bi-directional handling (Xiubo
     Li + Mike Christie + Ilias Tsitsimpis)

   - Fix iscsi-target TMR reference leak during session shutdown (Rob
     Millner + Chu Yuan Lin)

   - Fix target_core_fabric_configfs.c race between LUN shutdown +
     mapped LUN creation (James Shen)

   - Fix target-core unknown fabric callback queue-full errors (Potnuri
     Bharat Teja)

   - Fix iscsi-target + iser-target queue-full handling in order to
     support iw_cxgb4 RNICs. (Potnuri Bharat Teja + Sagi Grimberg)

   - Fix ALUA transition state race between multiple initiator (Mike
     Christie)

   - Drop work-around for legacy GlobalSAN initiator, to allow QLogic
     57840S + 579xx offload HBAs to work out-of-the-box in MSFT
     environments. (Martin Svec + Arun Easi)

  Note that a number are CC'ed for stable, and although the queue-full
  bug-fixes required for iser-target to work with iw_cxgb4 aren't CC'ed
  here, they'll be posted to Greg-KH separately"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  tcmu: Skip Data-Out blocks before gathering Data-In buffer for BIDI case
  iscsi-target: Drop work-around for legacy GlobalSAN initiator
  target: Fix ALUA transition state race between multiple initiators
  iser-target: avoid posting a recv buffer twice
  iser-target: Fix queue-full response handling
  iscsi-target: Propigate queue_data_in + queue_status errors
  target: Fix unknown fabric callback queue-full errors
  tcmu: Fix wrongly calculating of the base_command_size
  tcmu: Fix possible overwrite of t_data_sg's last iov[]
  target: Avoid mappedlun symlink creation during lun shutdown
  iscsi-target: Fix TMR reference leak during session shutdown
  usb: gadget: Correct usb EP argument for BOT status request
  tcmu: Allow cmd_time_out to be set to zero (disabled)

Pull cgroup fixes from Tejun Heo:
 "This contains fixes for two long standing subtle bugs:

   - kthread_bind() on a new kthread binds it to specific CPUs and
     prevents userland from messing with the affinity or cgroup
     membership. Unfortunately, for cgroup membership, there's a window
     between kthread creation and kthread_bind*() invocation where the
     kthread can be moved into a non-root cgroup by userland.

     Depending on what controllers are in effect, this can assign the
     kthread unexpected attributes. For example, in the reported case,
     workqueue workers ended up in a non-root cpuset cgroups and had
     their CPU affinities overridden. This broke workqueue invariants
     and led to workqueue stalls.

     Fixed by closing the window between kthread creation and
     kthread_bind() as suggested by Oleg.

   - There was a bug in cgroup mount path which could allow two
     competing mount attempts to attach the same cgroup_root to two
     different superblocks.

     This was caused by mishandling return value from kernfs_pin_sb().

     Fixed"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: avoid attaching a cgroup root to two different superblocks
  cgroup, kthread: close race window where new kthreads can be migrated to non-root cgroups

Pull libata fixes from Tejun Heo:
 "Two libata fixes.

  One to disable hotplug on VT6420 which never worked properly. The
  other reverts an earlier patch which disabled the second port on
  SB600/700. There were some confusions due to earlier datasheets which
  incorrectly indicated that the second port is not implemented on both
  SB600 and 700"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  sata_via: Enable hotplug only on VT6421
  Revert "pata_atiixp: Don't use unconnected secondary port on SB600/SB700"

Pull HID fixes from Jiri Kosina:

 - revert of a commit that switched all Synaptics touchpads over to be
   driven by hid-rmi. It turns out that this caused several user-visible
   regressions, and therefore we revert back to the original state
   before all the reported issues have been fixed.

 - a new uclogic device ID addition, from Xiaolei Yu.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  Revert "HID: rmi: Handle all Synaptics touchpads using hid-rmi"
  HID: uclogic: add support for Ugee Tablet EX07S

On SPARC, the udl driver filled my kernel log with these messages:

[186668.910612] Kernel unaligned access at TPC[76609c] udl_render_hline+0x13c/0x3a0

Use put_unaligned_be16 to avoid them. On x86 this results in the same
code, but on SPARC the compiler emits two single-byte stores.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407200229.20642-1-j.neuschaefer@gmx.net

Only call synchronize_rcu_expedited after unlocking struct_mutex to
avoid deadlock because the workqueues depend on struct_mutex.

>From original patch by Andrea:

synchronize_rcu/synchronize_sched/synchronize_rcu_expedited() will
hang until its own workqueues are run. The i915 gem workqueues will
wait on the struct_mutex to be released. So we cannot wait for a
quiescent state using those rcu primitives while holding the
struct_mutex or it creates a circular lock dependency resulting in
kernel hangs (which is reproducible but goes undetected by lockdep).

kswapd0         D    0   700      2 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? _synchronize_rcu_expedited.constprop.65+0x2ef/0x300
? wake_up_bit+0x20/0x20
? rcu_stall_kick_kthreads.part.54+0xc0/0xc0
? rcu_exp_wait_wake+0x530/0x530
? i915_gem_shrink+0x34b/0x4b0
? i915_gem_shrinker_scan+0x7c/0x90
? i915_gem_shrinker_scan+0x7c/0x90
? shrink_slab.part.61.constprop.72+0x1c1/0x3a0
? shrink_zone+0x154/0x160
? kswapd+0x40a/0x720
? kthread+0xf4/0x130
? try_to_free_pages+0x450/0x450
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
plasmashell     D    0  4657   4614 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? i915_gem_close_object+0x26/0xc0
? i915_gem_close_object+0x26/0xc0
? drm_gem_object_release_handle+0x48/0x90
? drm_gem_handle_delete+0x50/0x80
? drm_ioctl+0x1fa/0x420
? drm_gem_handle_create+0x40/0x40
? pipe_write+0x391/0x410
? __vfs_write+0xc6/0x120
? do_vfs_ioctl+0x8b/0x5d0
? SyS_ioctl+0x3b/0x70
? entry_SYSCALL_64_fastpath+0x13/0x94
kworker/0:0     D    0 29186      2 0x00000000
Workqueue: events __i915_gem_free_work
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? del_timer_sync+0x44/0x50
? update_curr+0x57/0x110
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_work+0x2d/0x40
? process_one_work+0x13a/0x3b0
? worker_thread+0x4a/0x460
? kthread+0xf4/0x130
? process_one_work+0x3b0/0x3b0
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30

Fixes: 3d3d18f0 ("drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)")
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 8f612d05)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

i915 is currently doing a full GPU reset at the end of
i915_gem_suspend() followed by GuC suspend in i915_drm_suspend(). This
GPU reset clobbers the GuC, causing the suspend request to then fail,
leaving the GuC in an undefined state. We need to tell the GuC to
suspend before we do the direct intel_gpu_reset().

v2: Commit message update. (Chris, Daniele)

Fixes: 1c777c5d ("drm/i915/hsw: Fix GPU hang during resume from S3-devices state")
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491387710-20553-1-git-send-email-sagar.a.kamble@intel.comReviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit fd089233)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

gvt-fixes-2017-04-07

- execlist csb initial read ptr fix (Min)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407084240.4d2ig5ja2umcnsq3@zhen-hp.sh.intel.com

This reverts commit 279967a6.

Multiple regressions [1] [2] [3] have been reported. The hid-rmi
support would have to fixed and redone in 4.11+.

[1] http://lkml.kernel.org/r/b79b88c8-770a-13f6-5668-c3a94254e5e0@gmail.com
[2] http://lkml.kernel.org/r/375e67b5-2cb8-3491-1d71-d8650d6e9451@gmail.com
[3] https://bugzilla.kernel.org/show_bug.cgi?id=195287Reported-by: Cameron Gutman <aicommander@gmail.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: Lorenzo J. Lucchini <ljlbox@tiscali.it>
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

After commit 47c950d1 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.

However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.

Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d1 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 57e5568f ("sata_via: Implement hotplug for VT6421") adds
hotplug IRQ handler for VT6421 but enables hotplug on all chips. This
is a bug because it causes "irq xx: nobody cared" error on VT6420 when
hot-(un)plugging a drive:

[  381.839948] irq 20: nobody cared (try booting with the "irqpoll" option)
[  381.840014] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc5+ #148
[  381.840066] Hardware name:          P4VM800/P4VM800, BIOS P1.60 05/29/2006
[  381.840117] Call Trace:
[  381.840167]  <IRQ>
[  381.840225]  ? dump_stack+0x44/0x58
[  381.840278]  ? __report_bad_irq+0x14/0x97
[  381.840327]  ? handle_edge_irq+0xa5/0xa5
[  381.840376]  ? note_interrupt+0x155/0x1cf
[  381.840426]  ? handle_edge_irq+0xa5/0xa5
[  381.840474]  ? handle_irq_event_percpu+0x32/0x38
[  381.840524]  ? handle_irq_event+0x1f/0x38
[  381.840573]  ? handle_fasteoi_irq+0x69/0xb8
[  381.840625]  ? handle_irq+0x4f/0x5d
[  381.840672]  </IRQ>
[  381.840726]  ? do_IRQ+0x2e/0x8b
[  381.840782]  ? common_interrupt+0x2c/0x34
[  381.840836]  ? mwait_idle+0x60/0x82
[  381.840892]  ? arch_cpu_idle+0x6/0x7
[  381.840949]  ? do_idle+0x96/0x18e
[  381.841002]  ? cpu_startup_entry+0x16/0x1a
[  381.841057]  ? start_kernel+0x319/0x31c
[  381.841111]  ? startup_32_smp+0x166/0x168
[  381.841165] handlers:
[  381.841219] [<c12a7263>] ata_bmdma_interrupt
[  381.841274] Disabling IRQ #20

Seems that VT6420 can do hotplug too (there's no documentation) but the
comments say that SCR register access (required for detecting hotplug
events) can cause problems on these chips.

For now, just keep hotplug disabled on anything other than VT6421.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

Run this:

    touch file0
    for ((; ;))
    {
        mount -t cpuset xxx file0
    }

And this concurrently:

    touch file1
    for ((; ;))
    {
        mount -t cpuset xxx file1
    }

We'll trigger a warning like this:

 ------------[ cut here ]------------
 WARNING: CPU: 1 PID: 4675 at lib/percpu-refcount.c:317 percpu_ref_kill_and_confirm+0x92/0xb0
 percpu_ref_kill_and_confirm called more than once on css_release!
 CPU: 1 PID: 4675 Comm: mount Not tainted 4.11.0-rc5+ #5
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
 Call Trace:
  dump_stack+0x63/0x84
  __warn+0xd1/0xf0
  warn_slowpath_fmt+0x5f/0x80
  percpu_ref_kill_and_confirm+0x92/0xb0
  cgroup_kill_sb+0x95/0xb0
  deactivate_locked_super+0x43/0x70
  deactivate_super+0x46/0x60
 ...
 ---[ end trace a79f61c2a2633700 ]---

Here's a race:

  Thread A				Thread B

  cgroup1_mount()
    # alloc a new cgroup root
    cgroup_setup_root()
					cgroup1_mount()
					  # no sb yet, returns NULL
					  kernfs_pin_sb()

					  # but succeeds in getting the refcnt,
					  # so re-use cgroup root
					  percpu_ref_tryget_live()
    # alloc sb with cgroup root
    cgroup_do_mount()

  cgroup_kill_sb()
					  # alloc another sb with same root
					  cgroup_do_mount()

					cgroup_kill_sb()

We end up using the same cgroup root for two different superblocks,
so percpu_ref_kill() will be called twice on the same root when the
two superblocks are destroyed.

We should fix to make sure the superblock pinning is really successful.

Cc: stable@vger.kernel.org # 3.16+
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Pull crypto fixes from Herbert Xu:
 "This fixes a number of bugs in the caam driver:

   - device creation fails after release

   - error-path NULL-pointer dereference

   - spurious hardware error in RNG deinstantiation"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: caam - fix RNG deinstantiation error checking
  crypto: caam - fix invalid dereference in caam_rsa_init_tfm()
  crypto: caam - fix JR platform device subsequent (re)creations

The retry queue is intended to provide a temporary buffer in the case
of transient errors when communicating with auditd, it is not meant
as a long life queue, that functionality is provided by the hold
queue.

This patch fixes a problem identified by Seth where the retry queue
could grow uncontrollably if an auditd instance did not connect to
the kernel to drain the queues.  This commit fixes this by doing the
following:

* Make sure we always call auditd_reset() if we decide the connection
with audit is really dead.  There were some cases in
kauditd_hold_skb() where we did not reset the connection, this patch
relocates the reset calls to kauditd_thread() so all the error
conditions are caught and the connection reset.  As a side effect,
this means we could move auditd_reset() and get rid of the forward
definition at the top of kernel/audit.c.

* We never checked the status of the auditd connection when
processing the main audit queue which meant that the retry queue
could grow unchecked.  This patch adds a call to auditd_reset()
after the main queue has been processed if auditd is not connected,
the auditd_reset() call will make sure the retry and hold queues are
correctly managed/flushed so that the retry queue remains reasonable.

Cc: <stable@vger.kernel.org> # 4.10.x-: 5b52330bReported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>

The commit 1259fedd("pinctrl: samsung: Fix the width of
PINCFG_TYPE_DRV bitfields for Exynos5433") already fixed
the different width of PINCFG_TYPE_DRV from previous Exynos SoC.

However wrong merge conflict resolution was chosen in commit
7f36f5d1 ("Merge tag 'v4.10-rc6' into devel") effectively dropping
the changes for PINCFG_TYPE_DRV.  Re-do them here.

The macro EXYNOS_PIN_BANK_EINTW is no longer used so remove it.

Fixes: 7f36f5d1 ("Merge tag 'v4.10-rc6' into devel")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull CIFS fixes from Steve French:
 "This is a set of CIFS/SMB3 fixes for stable.

  There is another set of four SMB3 reconnect fixes for stable in
  progress but they are still being reviewed/tested, so didn't want to
  wait any longer to send these five below"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  Reset TreeId to zero on SMB2 TREE_CONNECT
  CIFS: Fix build failure with smb2
  Introduce cifs_copy_file_range()
  SMB3: Rename clone_range to copychunk_range
  Handle mismatched open calls

Pull ARM fixes from Russell King:
 "A number of ARM fixes:

   - prevent oopses caused by dma_get_sgtable() and declared DMA
     coherent memory

   - fix boot failure on nommu caused by ID_PFR1 access

   - a number of kprobes fixes from Jon Medhurst and Masami Hiramatsu"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8665/1: nommu: access ID_PFR1 only if CPUID scheme
  ARM: dma-mapping: disallow dma_get_sgtable() for non-kernel managed memory
  arm: kprobes: Align stack to 8-bytes in test code
  arm: kprobes: Fix the return address of multiple kretprobes
  arm: kprobes: Skip single-stepping in recursing path if possible
  arm: kprobes: Allow to handle reentered kprobe on single-stepping

Merge tag 'driver-core-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are 3 small fixes for 4.11-rc6.

  One resolves a reported issue with sysfs files that NeilBrown found,
  one is a documenatation fix for the stable kernel rules, and the last
  is a small MAINTAINERS file update for kernfs"

* tag 'driver-core-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  MAINTAINERS: separate out kernfs maintainership
  sysfs: be careful of error returns from ops->show()
  Documentation: stable-kernel-rules: fix stable-tag format

Pull staging/IIO driver rfixes from Greg KH:
 "Here are a number of small IIO and staging driver fixes for 4.11-rc6.
  Nothing big here, just iio fixes for reported issues, and an ashmem
  fix for a very old bug that has been reported by a number of Android
  vendors"

* tag 'staging-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: android: ashmem: lseek failed due to no FMODE_LSEEK.
  iio: hid-sensor-attributes: Fix sensor property setting failure.
  iio: accel: hid-sensor-accel-3d: Fix duplicate scan index error
  iio: core: Fix IIO_VAL_FRACTIONAL_LOG2 for negative values
  iio: st_pressure: initialize lps22hb bootime
  iio: bmg160: reset chip when probing
  iio: cros_ec_sensors: Fix return value to get raw and calibbias data.

Pull VFS fixes from Al Viro:
 "statx followup fixes and a fix for stack-smashing on alpha"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  alpha: fix stack smashing in old_adjtimex(2)
  statx: Include a mask for stx_attributes in struct statx
  statx: Reserve the top bit of the mask for future struct expansion
  xfs: report crtime and attribute flags to statx
  ext4: Add statx support
  statx: optimize copy of struct statx to userspace
  statx: remove incorrect part of vfs_statx() comment
  statx: reject unknown flags when using NULL path
  Documentation/filesystems: fix documentation for ->getattr()

Pull block fixes from Jens Axboe:
 "Here's a pull request for 4.11-rc, fixing a set of issues mostly
  centered around the new scheduling framework. These have been brewing
  for a while, but split up into what we absolutely need in 4.11, and
  what we can defer until 4.12. These are well tested, on both single
  queue and multiqueue setups, and with and without shared tags. They
  fix several hangs that have happened in testing.

  This is obviously larger than I would have preferred at this point in
  time, but I don't think we can shave much off this and still get the
  desired results.

  In detail, this pull request contains:

   - a set of five fixes for NVMe, mostly from Christoph and one from
     Roland.

   - a series from Bart, fixing issues with dm-mq and SCSI shared tags
     and scheduling. Note that one of those patches commit messages may
     read like an optimization, but it is in fact an important fix for
     queue restarts in particular.

   - a series from Omar, most importantly fixing a hang with multiple
     hardware queues when we fail to get a driver tag. Another important
     fix in there is for resizing hardware queues, which nbd does when
     handling multiple sockets for one connection.

   - fixing an imbalance in putting the ctx for hctx request allocations
     from Minchan"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: Restart a single queue if tag sets are shared
  dm rq: Avoid that request processing stalls sporadically
  scsi: Avoid that SCSI queues get stuck
  blk-mq: Introduce blk_mq_delay_run_hw_queue()
  blk-mq: remap queues when adding/removing hardware queues
  blk-mq-sched: fix crash in switch error path
  blk-mq-sched: set up scheduler tags when bringing up new queues
  blk-mq-sched: refactor scheduler initialization
  blk-mq: use the right hctx when getting a driver tag fails
  nvmet: fix byte swap in nvmet_parse_io_cmd
  nvmet: fix byte swap in nvmet_execute_write_zeroes
  nvmet: add missing byte swap in nvmet_get_smart_log
  nvme: add missing byte swap in nvme_setup_discard
  nvme: Correct NVMF enum values to match NVMe-oF rev 1.0
  block: do not put mq context in blk_mq_alloc_request_hctx

Pull pin control fix from Linus Walleij:
 "This late fix for pin control is hopefully the last I send this cycle.

  The problem was detected early in the v4.11 release cycle and there
  has been some back and forth on how to solve it. Sadly the proper fix
  arrives late, but at least not too late.

  An issue was detected with pin control on the Freescale i.MX after the
  refactorings for more general group and function handling.

  We now have the proper fix for this"

* tag 'pinctrl-v4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()

Pull powerpc fixes from Michael Ellerman:
 "Some more powerpc fixes for 4.11:

  Headed to stable:

   - disable HFSCR[TM] if TM is not supported, fixes a potential host
     kernel crash triggered by a hostile guest, but only in
     configurations that no one uses

   - don't try to fix up misaligned load-with-reservation instructions

   - fix flush_(d|i)cache_range() called from modules on little endian
     kernels

   - add missing global TLB invalidate if cxl is active

   - fix missing preempt_disable() in crc32c-vpmsum

  And a fix for selftests build changes that went in this release:

   - selftests/powerpc: Fix standalone powerpc build

  Thanks to: Benjamin Herrenschmidt, Frederic Barrat, Oliver O'Halloran,
  Paul Mackerras"

* tag 'powerpc-4.11-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/crypto/crc32c-vpmsum: Fix missing preempt_disable()
  powerpc/mm: Add missing global TLB invalidate if cxl is active
  powerpc/64: Fix flush_(d|i)cache_range() called from modules
  powerpc: Don't try to fix up misaligned load-with-reservation instructions
  powerpc: Disable HFSCR[TM] if TM is not supported
  selftests/powerpc: Fix standalone powerpc build

In the case that compat_get_bitmap fails we do not want to copy the
bitmap to the user as it will contain uninitialized stack data and leak
sensitive data.
Signed-off-by: Chris Salls <salls@cs.ucsb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, inputting the following command will succeed but actually the
value will be truncated:

  # echo 0x12ffffffff > /proc/sys/net/ipv4/tcp_notsent_lowat

This is not friendly to the user, so instead, we should report error
when the value is larger than UINT_MAX.

Fixes: e7d316a0 ("sysctl: handle error writing UINT_MAX to u32 fields")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Separate out kernfs from driver core and add myself as a
co-maintainer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ops->show() can return a negative error code.
Commit 65da3484 ("sysfs: correctly handle short reads on PREALLOC attrs.")
(in v4.4) caused this to be stored in an unsigned 'size_t' variable, so errors
would look like large numbers.
As a result, if an error is returned, sysfs_kf_read() will return the
value of 'count', typically 4096.

Commit 17d0774f ("sysfs: correctly handle read offset on PREALLOC attrs")
(in v4.8) extended this error to use the unsigned large 'len' as a size for
memmove().
Consequently, if ->show returns an error, then the first read() on the
sysfs file will return 4096 and could return uninitialized memory to
user-space.
If the application performs a subsequent read, this will trigger a memmove()
with extremely large count, and is likely to crash the machine is bizarre ways.

This bug can currently only be triggered by reading from an md
sysfs attribute declared with __ATTR_PREALLOC() during the
brief period between when mddev_put() deletes an mddev from
the ->all_mddevs list, and when mddev_delayed_delete() - which is
scheduled on a workqueue - completes.
Before this, an error won't be returned by the ->show()
After this, the ->show() won't be called.

I can reproduce it reliably only by putting delay like
	usleep_range(500000,700000);
early in mddev_delayed_delete(). Then after creating an
md device md0 run
  echo clear > /sys/block/md0/md/array_state; cat /sys/block/md0/md/array_state

The bug can be triggered without the usleep.

Fixes: 65da3484 ("sysfs: correctly handle short reads on PREALLOC attrs.")
Fixes: 17d0774f ("sysfs: correctly handle read offset on PREALLOC attrs")
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A patch documenting how to specify which kernels a particular fix should
be backported to (seemingly) inadvertently added a minus sign after the
kernel version. This particular stable-tag format had never been used
prior to this patch, and was neither present when the patch in question
was first submitted (it was added in v2 without any comment).

Drop the minus sign to avoid any confusion.

Fixes: fdc81b79 ("stable_kernel_rules: Add clause about specification of kernel versions to patch.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs_llseek will check whether the file mode has
FMODE_LSEEK, no return failure. But ashmem can be
lseek, so add FMODE_LSEEK to ashmem file.

Comment From Greg Hackmann:
	ashmem_llseek() passes the llseek() call through to the backing
	shmem file.  91360b02 ("ashmem: use vfs_llseek()") changed
	this from directly calling the file's llseek() op into a VFS
	layer call.  This also adds a check for the FMODE_LSEEK bit, so
	without that bit ashmem_llseek() now always fails with -ESPIPE.

Fixes: 91360b02 ("ashmem: use vfs_llseek()")
Signed-off-by: Shuxiao Zhang <zhangshuxiao@xiaomi.com>
Tested-by: Greg Hackmann <ghackmann@google.com>
Cc: stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull sparc fixes from David Miller:
 "Several fixes here, mostly having to due with either build errors or
  memory corruptions depending upon whether you have THP enabled or not"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: remove unused wp_works_ok macro
  sparc32: Export vac_cache_size to fix build error
  sparc64: Fix memory corruption when THP is enabled
  sparc64: Fix kernel panic due to erroneous #ifdef surrounding pmd_write()
  arch/sparc: Avoid DCTI Couples
  sparc64: kern_addr_valid regression
  sparc64: Add support for 2G hugepages
  sparc64: Fix size check in huge_pte_alloc