- 29 Nov, 2018 7 commits
-
-
Gaurav K Singh authored
This computation of RC params happens in the atomic commit phase during compute_config() to validate if display stream compression can be enabled for the requested mode. v7 (From Manasi): * Use DRM_DEBUG instead of DRM_ERROR (Ville) * Use Error numberinstead of -1 (Ville) v6 (From Manasi): * Use 9 instead of 0x9 for consistency (Anusha) v5 (From Manasi): * Fix dim checkpatch warnings/checks v4(From Gaurav): * No change.Rebase on drm-tip v3 (From Gaurav): * Rebase on top of Manasi's latest series * Return -ve value in case of failure scenarios (Manasi) Fix review comments from Ville: * Remove unnecessary comments * Remove unnecessary paranthesis * Add comments for few RC params calculations v2 (From Manasi): * Rebase Gaurav's patch from intel-gfx to gfx-internal * Use struct drm_dsc_cfg instead of struct intel_dp as a parameter Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Signed-off-by:
Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com> Reviewed-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-5-manasi.d.navare@intel.com
-
Gaurav K Singh authored
This patches does the following: 1. This patch defines all the DSC parameters as per the VESA DSC specification. These are stored in the encoder and used to compute the PPS parameters to be sent to the Sink. 2. Compute all the DSC parameters which are derived from DSC state of intel_crtc_state. 3. Compute all parameters that are VESA DSC specific This computation happens in the atomic check phase during compute_config() to validate if display stream compression can be enabled for the requested mode. v8 (From Manasi): * DEBUG_KMS instead of DRM_ERROR for user triggerable errors (Ville) v7: (From Manasi) * Dont use signed int for rc_range_params (Manasi) * Mask the range_bpg_offset to use only 6 bits * Add SPDX identifier (Chris Wilson) v6 (From Manasi): * Add a check for line_buf_depth return value (Anusha) * Remove DRM DSC constants to different patch (Manasi) v5 (From Manasi): * Add logic to limit the max line buf depth for DSC 1.1 to 13 as per DSC 1.1 spec * Fix dim checkpatch warnings/checks v4 (From Gaurav): * Rebase on latest drm tip * rename variable name(Manasi) * Populate linebuf_depth variable(Manasi) v3 (From Gaurav): * Rebase my previous patches on top of Manasi's latest patch series * Using >>n rather than /2^n (Manasi) * Change the commit message to explain what the patch is doing(Gaurav) Fixed review comments from Ville: * Don't use macro TWOS_COMPLEMENT * Mention in comment about the source of RC params * Return directly from case statements * Using single asssignment for assigning rc_range_params * Using <<n rather than *2^n and removing the comments about the fixed point numbers v2 (From Manasi): * Update logic for minor version to consider the dpcd value and what supported by the HW platform * Use DRM DSC config struct instead of intel_dp struct * Move the DSC constants to DRM DSC header file * Use u16, u8 where bigger data types not needed * * Compute the DSC parameters as part of DSC compute config since the computation can fail (Manasi) Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by:
-
Manasi Navare authored
If a eDP panel supports both PSR2 and VDSC, our HW cannot support both at a time. Give priority to PSR2 if a requested resolution can be supported without compression else enable VDSC and keep PSR2 disabled. v4: Fix the unrealted stuff removed during rebase (Ville) v3: * Rebase v2: * Add warning for DSC and PSR2 enabled together (DK) Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-3-manasi.d.navare@intel.com
-
Manasi Navare authored
DSC params like the enable, compressed bpp, slice count and dsc_split are added to the intel_crtc_state. These parameters are set based on the requested mode and available link parameters during the pipe configuration in atomic check phase. These values are then later used to populate the remaining DSC and RC parameters before enbaling DSC in atomic commit. v15: * Rebase over drm-tip v14: Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville) v13: * Compute DSC bpc only when DSC is req to be enabled (Ville) v12: * Override bpp with dsc dpcd color depth (Manasi) v11: * Const crtc_state, reject DSC on DP without FEC (Ville) * Dont set dsc_split to false (Ville) v10: * Add a helper for dp_dsc support (Ville) * Set pipe_config to max bpp, link params for DSC for now (Ville) * Compute bpp - use dp dsc support helper (Ville) v9: * Rebase on top of drm-tip that now uses fast_narrow config for edp (Manasi) v8: * Check for DSC bpc not 0 (manasi) v7: * Fix indentation in compute_m_n (Manasi) v6 (From Gaurav): * Remove function call of intel_dp_compute_dsc_params() and invoke intel_dp_compute_dsc_params() in the patch where it is defined to fix compilation warning (Gaurav) v5: Add drm_dsc_cfg in intel_crtc_state (Manasi) v4: * Rebase on refactoring of intel_dp_compute_config on tip (Manasi) * Add a comment why we need to check PSR while enabling DSC (Gaurav) v3: * Check PPR > max_cdclock to use 2 VDSC instances (Ville) v2: * Add if-else for eDP/DP (Gaurav) Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by:
Ville Syrjala <ville.syrjala@linux.intel.com> Acked-by:
Jani Nikula <jani.nikula@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181128213621.21391-1-manasi.d.navare@intel.com
-
Manasi Navare authored
Basic DSC parameters and DSC configuration data needs to be computed for each of the requested mode during atomic check. This is required since for certain modes, valid DSC parameters and config data might not be computed in which case compression cannot be enabled for that mode. For that reason we need to add these params and config structure to the intel_crtc_state so that if valid this state information can directly be used while enabling DSC in atomic commit. v2: * Rebase on drm-tip (Manasi) Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by:
-
Ville Syrjälä authored
In the future framebuffer stride alignment requirements won't exactly match the units in which skl+ plane stride is specified. So extract the code for the skl+ stuff into a separate helper. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk>
-
Ville Syrjälä authored
Let's try to make sure the fb offset computations never hit an integer overflow by making sure the entire fb stays below 32bits. framebuffer_check() in the core already does the same check, but as it doesn't know about tiling some things can slip through. Repeat the check in the driver with tiling taken into account. v2: Use add_overflows() after massaging it to work for me (Chris) v3: Call it add_overflow_t() to match min_t() & co. (Chris) Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
- 28 Nov, 2018 17 commits
-
-
Ville Syrjälä authored
On icl+ the plane state that gets passed to update_slave() is not the plane state of the plane we're programming. With NV12 the plane state would be coming from the master (UV) plane whereas the plane we're programming is the slave (Y) plane. For that reason we need to explicitly pass around the slave plane (or we'd have to otherwise deduce it by checking whether we were called via .update_plane() or .update_slave()). In the case of icl_program_input_csc_coeff() it's actually OK to assume that we are always the master plane because the input CSC only exists on HDR planes which can never be a slave plane. But for consistency let's pass in the plane explicitly anyway. While at it drop the "_coeff" from the function name since it's kinda redundant, and this makes the name a bit shorter :) Cc: Uma Shankar <uma.shankar@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
Uma Shankar <uma.shankar@intel.com> Reviewed-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by:
Matt Roper <matthew.d.roper@intel.com>
-
Ville Syrjälä authored
A variable whose name is 'plane_id' is expected to be of the enum plane_id type. In this case we have a raw int, which turns out to refer to the plane of the framebuffer. Rename the variable to 'color_plane' in line with the trend started earlier. Signed-off-by:
-
Ville Syrjälä authored
skl+ can go belly up if there are overlapping ddb allocations between planes. If we could absolutely guarantee that we can perform the atomic update within a single frame we shouldn't have to worry about this. But we can't rely on that so let's steal the ddb overlap check trick from skl_update_crtcs() and apply it to the plane updates. Since each step of the sequence is free from ddb overlaps we don't have to worry about a vblank sneaking up on us in the middle of the sequence. The partial state that gets latched by the hardware will be safe. And unlike skl_update_crtcs() we don't have to intoduce any extra vblank waits on account of only having to worry about a single pipe. v2: Fix typo in commit msg (Matt) Signed-off-by:
-
Ville Syrjälä authored
On SKL+ the plane WM/BUF_CFG registers are a proper part of each plane's register set. That means accessing them will cancel any pending plane update, and we would need a PLANE_SURF register write to arm the wm/ddb change as well. To avoid all the problems with that let's just move the wm/ddb programming into the plane update/disable hooks. Now all plane registers get written in one (hopefully atomic) operation. To make that feasible we'll move the plane ddb tracking into the crtc state. Watermarks were already tracked there. v2: Rebase due to input CSC v3: Split out a bunch of junk (Matt) v4: Add skl_wm_add_affected_planes() to deal with cursor special case and non-zero wm register reset value v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt) Remove the redundant ddb memset() (Matt) Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3 Signed-off-by: -
Ville Syrjälä authored
Simplify the calling convention of the skl+ watermark functions by not passing around dev_priv needlessly. The callees have what they need to dig it out anyway. Signed-off-by:
-
Ville Syrjälä authored
Make a cleaner split between the skl+ and icl+ ways of computing watermarks. This way skl_build_pipe_wm() doesn't have to know any of the gritty details of icl+ master/slave planes. We can also simplify a bunch of the lower level code by pulling the plane visibility checks a bit higher up. v2: WARN_ON(!visible) for the icl+ master plane case (Matt) Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by:
-
Ville Syrjälä authored
We have to pass both level 0 watermark struct and the transition watermark struct to skl_compute_transition_wm(). Make life less confusing by just passing the entire plane watermark struct that contains both aforementioned structures. Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Ville Syrjälä authored
We memset(0) the entire watermark struct the start, so there's no need to clear things later on. v2: Rebase due to some stale w/a removal Reviewed-by:
-
Ville Syrjälä authored
If the level 0 latency is 0 we can't do anything. Return an error rather than success. While this can't happen due to WaWmMemoryReadLatency, it can happen if the user clears out the level 0 latency via debugfs. v2: Clarify how how we can end here with zero level 0 latency (Matt) Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by:
-
Ville Syrjälä authored
We're going to need access to the new crtc state in ->disable_plane() for SKL+ wm/ddb programming and pre-skl pipe gamma/csc control. Pass the crtc state down. We'll also try to make intel_crtc_disable_planes() do the right thing as much as it's possible. The fact that we don't have a separate crtc state for the disabled state when we're going to re-enable the crtc later means we might end up poking at a few extra planes in there. But that's harmless. I suppose one might argue that we wouldn't have to care about proper ddb/wm/csc/gamma if the pipe is going to permanently disable anyway, but the state checker probably cares so we should try our best to make sure everything is programmed correctly even in that case. v2: Fix the commit message a bit (Matt) Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Ville Syrjälä authored
Keep track which planes need updating during the commit. For now we set the bit for any plane that was or will be visible (including icl+ nv12 slave planes). In the future I'll have need to update invisible planes as well, for skl plane ddbs and for pre-skl pipe gamma/csc control (which lives in the primary plane control register). v2: Pimp the commit message to mention icl+ nv12 slave planes (Matt) Reviewed-by:
-
Ville Syrjälä authored
The plane color correction registers are single buffered. So ideally we would write them at the start of vblank just after the double buffered plane registers have been latched. Since we have no convenient way to do that for now let's at least move the single buffered register writes to happen after the double buffered registers have been written. Reviewed-by:
-
Ville Syrjälä authored
Some observations about the plane registers: - the control register will self-arm if the plane is not already enabled, thus we want to write it as close to (or ideally after) the surface register - tileoff/linoff/offset/aux_offset are self-arming as well so we want them close to the surface register as well - color keying registers we maybe self arming before SKL. Not 100% sure but we can try to keep them near to the surface register as well - chv pipe b csc register are double buffered but self arming so moving them down a bit - the rest should be mostly armed by the surface register so we can safely write them first, and to just for some consistency let's try to follow keep them in order based on the register offset None of this will have any effect of course unless the vblank evasion fails (which it still does sometimes). Another potential future benefit might be pulling the non-self armings registers outside the vblank evasion since they won't latch until the arming register has been written. This would make the critical section a bit lighter and thus less likely to exceed the deadline. v2: Rebase due to input CSC v3: Swap LINOFF/TILEOFF and KEYMSK/KEYMAX to actually follow the last rule above (Matt) Add a bit more rationale to the commit message (Matt) Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: -
Chris Wilson authored
Mark A0 as the one and only pre-production variant of Kabylake and remove its couple of workarounds, consigning them to the annals of history. Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Acked-by:
-
Manasi Navare authored
DSC specification defines linebuf_depth which contains the line buffer bit depth used to generate the bitstream. These values are defined as per Table 4.1 in DSC 1.2 spec v2 (From Manasi): * Rename as MAX_LINEBUF_DEPTH for DSC 1.1 and DSC 1.2 Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Manasi Navare authored
According to Display Stream compression spec 1.2, the picture parameter set metadata is sent from source to sink device using the DP Secondary data packet. An infoframe is formed for the PPS SDP header and PPS SDP payload bytes. This patch adds helpers to fill the PPS SDP header and PPS SDP payload according to the DSC 1.2 specification. v7: * Use BUILD_BUG_ON() to protect changing struct size (Ville) * Remove typecaseting (Ville) * Include byteorder.h in drm_dsc.c (Ville) * Correct kernel doc spacing (Anusha) v6: * Use proper sequence points for breaking down the assignments (Chris Wilson) * Use SPDX identifier v5: Do not use bitfields for DRM structs (Jani N) v4: * Use DSC constants for params that dont change across configurations v3: * Add reference to added kernel-docs in Documentation/gpu/drm-kms-helpers.rst (Daniel Vetter) v2: * Add EXPORT_SYMBOL for the drm functions (Manasi) Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Harry Wentland <harry.wentland@amd.com> Reviewed-by:
-
Srivatsa, Anusha authored
DSC has some Rate Control values that remain constant across all configurations. These are as per the DSC standard. v3: * Define them in drm_dsc.h as they are DSC constants (Manasi) v2: * Add DP_DSC_ prefix (Jani Nikula) Cc: dri-devel@lists.freedesktop.org Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
- 27 Nov, 2018 4 commits
-
-
Manasi Navare authored
This defines all the DSC parameters as per the VESA DSC spec that will be required for DSC encoder/decoder v6: (From Manasi) * Add a bit mask for RANGE_BPG_OFFSET for 6 bits(Manasi) v5 (From Manasi) * Add the RC constants as per the spec v4 (From Manasi) * Add the DSC_MUX_WORD_SIZE constants (Manasi) v3 (From Manasi) * Remove the duplicate define (Suggested By:Harry Wentland) v2: Define this struct in DRM (From Manasi) * Changed the data types to u8/u16 instead of unsigned longs (Manasi) * Remove driver specific fields (Manasi) * Move this struct definition to DRM (Manasi) * Define DSC 1.2 parameters (Manasi) * Use DSC_NUM_BUF_RANGES (Manasi) * Call it drm_dsc_config (Manasi) Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Manasi Navare authored
This patch defines a new header file for all the DSC 1.2 structures and creates a structure for PPS infoframe which will be used to send picture parameter set secondary data packet for display stream compression. All the PPS infoframe syntax elements are taken from DSC 1.2 specification from VESA. v4: * Remove redundant blankline in doc (Ville) * use drm_dsc namespace for all structs (Ville) * Use packed struct (Ville) v3: * Add the SPDX shorthand (Chris Wilson) v2: * Do not use bitfields in the struct (Jani Nikula) Cc: Gaurav K Singh <gaurav.k.singh@intel.com> Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Manasi Navare authored
DSC DPCD color depth register advertises its color depth capabilities by setting each of the bits that corresponding to a specific color depth. This patch defines those specific color depths and adds a helper to return an array of color depth capabilities. v2: * Simplify the logic (Ville) Signed-off-by:
-
Chris Wilson authored
If the engine's seqno is already at our target seqno (most likely it hasn't been used since the last reset), we can skip serialising the engine and leave it as is. Signed-off-by:
-
- 26 Nov, 2018 1 commit
-
-
Chris Wilson authored
We may be simply restarting too fast for the culmudgeonly gen3/gen4 as we still see missing interrupts following a reset. So let's try restarting a little slower, first wake up the ring empty and then tell it about the work it has to perform. References: https://bugs.freedesktop.org/show_bug.cgi?id=108735Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181126122821.4537-1-chris@chris-wilson.co.uk
-
- 23 Nov, 2018 1 commit
-
-
Chris Wilson authored
Currently, we convert the error state into a string every time we read from sysfs (and sysfs reads in page size (4KiB) chunks). We do try to window the string and only capture the portion that is being read, but that means that we must always convert up to the window to find the start. For a very large error state bordering on EXEC_OBJECT_CAPTURE abuse, this is noticeable as it degrades to O(N^2)! As we do not have a convenient hook for sysfs open(), and we would like to keep the lazy conversion into a string, do the conversion of the whole string on the first read and keep the string until the error state is freed. v2: Don't double advance simple_read_from_buffer v3: Due to extreme pain of lack of vrealloc, use a scatterlist v4: Keep the forward iterator loosely cached v5: Stylistic improvements to reduce patch size Reported-by:
Jason Ekstrand <jason@jlekstrand.net> Testcase: igt/gem_exec_capture/many* Signed-off-by:
-
- 22 Nov, 2018 10 commits
-
-
José Roberto de Souza authored
We should not access hardware while computing config also we don't support stereo 3D so this test was never true. Suggested-by:
José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-6-jose.souza@intel.com
-
José Roberto de Souza authored
If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR will still keep the error set even after the reset done in the irq_preinstall and irq_uninstall hooks. And enabling in this situation cause the screen to freeze in the first time that PSR HW tries to activate so lets keep PSR disabled to avoid any rendering problems. v5: rebased: using edp_psr_shift() v4: Moved handling from intel_psr_compute_config() to intel_psr_init() to avoid hardware access during compute(Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
-
José Roberto de Souza authored
While PSR is active hardware will do aux transactions by it self to wakeup sink to receive a new frame when necessary. If that transaction is not acked by sink, hardware will trigger this interruption. So let's disable PSR as it is a hint that there is problem with this sink. The removed FIXME was asking to manually train the link but we don't need to do that as by spec sink should do a short pulse when it is out of sync with source, we just need to make sure it is awaken and the SDP header with PSR inactive set it will trigger the short pulse with a error set in the link status. v3: added workarround to fix scheduled work starvation cause by to frequent PSR error interruption v4: only setting irq_aux_error as we don't care in clear it and not using dev_priv->irq_lock as consequence. v5: rebased: using edp_psr_shift() Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
-
José Roberto de Souza authored
When we detect a error and disable PSR, it is kept disabled until the next modeset but as the sink already show signs that it do not properly work with PSR lets disabled it for good to avoid any additional flickering. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
-
José Roberto de Souza authored
When a PSR error happens sink sets the PSR error register and also set the link status to a error status. So in the short pulse handling it was returning earlier and doing a full detection and attempting to retrain but it fails as PSR HW is in change of the main-link. Just call intel_psr_short_pulse() before intel_dp_needs_link_retrain() is not the right fix as intel_dp_needs_link_retrain() would return true and trigger a full detection while PSR HW is still in change of main-link. Check for PSR active is also not safe as it could be inactive due a frontbuffer invalidate and still doing the PSR exit sequence. v3: added comment in intel_dp_needs_link_retrain() Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
-
José Roberto de Souza authored
Some eDP panels do not set a valid sink count value and even for the ones that sets is should always be one for eDP, that is why it is not cached in intel_edp_init_dpcd(). But intel_dp_short_pulse() compares the old count with the read one if there is a mistmatch a full port detection will be executed, what was happening in the first short pulse interruption of eDP panels that sets sink count. Instead of just skip the compasison for eDP panels, lets not read the sink count at all for eDP. v2: the previous version of this patch it was caching the sink count in intel_edp_init_dpcd() but I was pointed out by Ville a patch that handled a case of a eDP panel that do not set sink count and as sink count is not used to eDP certification was choosed to just not read it at all. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
-
Lyude Paul authored
While trying to add a chamelium test for short HPD IRQs, I ran into issues where a hotplug storm would be triggered, but the point at which it would be reported by the kernel would be after igt actually finished checking i915_hpd_storm_ctl's status. So, fix this by simply synchronizing our IRQ work, dig_port_work, and hotplug_work before printing out the HPD storm status in i915_hpd_storm_ctl_show(). Signed-off-by:
Lyude Paul <lyude@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20181121003718.17704-1-lyude@redhat.com
-
Ville Syrjälä authored
Replace the messy framebuffer format/modifier validation code with a single call to drm_any_plane_has_format(). The code was extremely annoying to maintain as you had to have a lot of platform checks for different formats. The new code requires zero maintenance. v2: Nuke the modifier checks as well since the core does that too now v3: Call drm_any_plane_has_format() from the driver code v4: Rebase Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
-
Jani Nikula authored
Signed-off-by:Jani Nikula <jani.nikula@intel.com>
-
Jani Nikula authored
Signed-off-by:
-
