- 11 Nov, 2018 20 commits
-
-
Martin Blumenstingl authored
The 32-bit Meson8 SoC can use the SAR ADC to read the chip temperature. This requires setting the correct TSC (temperature sensor coefficient), which is programmed into the eFuse during the manufacturing process. Meson8b and Meson8m2 are not supported yet because they have a 5-bit TSC and only the first four bits are stored inside the SAR ADC registers. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
This patch adds a channel type check at the beginning of the ad2s90_read_raw function. Since ad2s90 has only one channel, it just checks if the given channel is the expected one and if not, return -EINVAL. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Victor Colombo authored
This patch adds the IIO_CHAN_INFO_SCALE mask to ad2s90_chan and implements the relative read behavior at ad2s90_read_raw. Signed-off-by: Victor Colombo <victorcolombo@gmail.com> Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
Previously, devm_iio_device_register was being called before the spi_setup call and the spi_device's max_speed_hz and mode assignments. This could lead to a race condition since the driver was still being set up after it was already made ready to use. To fix it, this patch moves the device registration to the end of ad2s90_probe. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
This patch removes an initial assignment to the variable ret at probe, that was always overwritten. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
Previously, ad2s90_probe ignored the return code from spi_setup, not handling its possible failure. This patch makes ad2s90_probe check if the code is an error code and, if so, do the following: - Call dev_err with an appropriate error message. - Return the spi_setup's error code. Note: The 'return ret' statement could be out of the 'if' block, but this whole block will be moved up in the function in the patch: 'staging:iio:ad2s90: Move device registration to the end of probe'. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
Previously, when spi_read returned an error code inside ad2s90_read_raw, the code was ignored and IIO_VAL_INT was returned. This patch makes the function return the error code returned by spi_read when it fails. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Renato Lui Geh authored
Variable val subtracted an uninitialized value on IIO_CHAN_INFO_OFFSET. This was fixed by assigning the correct value instead. Signed-off-by: Renato Lui Geh <renatogeh@gmail.com> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nishad Kamdar authored
Add device tree table for matching vendor ID. Note that as the driver is still heavily in flux and there are some non obvious aspects to a comprehensive binding, that binding will be submitted at a later date (before leaving staging!) Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nishad Kamdar authored
Drop gpioin flag which decides how the GPIOs are controlled as the GPIOs must be outputs for the host as per the datasheet. Removes need for platform data so that is dropped as well. Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nishad Kamdar authored
Use the gpiod interface instead of the deprecated old non-descriptor interface. Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matt Ranostay authored
Report the step range of the respective potentiometers that are possible to userspace. Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Charles-Antoine Couret authored
Description how to invoke ti-dac7311 driver from device tree file. Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Charles-Antoine Couret authored
It is a driver for Texas Instruments 8/10/12-bit 1-channel compatible with DAC6311 and DAC5311 chips. Datasheet of this chip: http://www.ti.com/lit/ds/symlink/dac7311.pdfSigned-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Martin Kelly authored
Add DT binding documentation for the LSM9DS1 magnetometer. Signed-off-by: Martin Kelly <martin@martingkelly.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Slawomir Stepien authored
The type promotion will kick in, so the comparison will work. Signed-off-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Martin Kelly authored
LIS3MDL and LSM9DS1 are missing BDU settings in their register maps, so add them. I don't have a LIS3MDL sensor to test, but this works correctly on the LSM9DS1, which has the same register map. Signed-off-by: Martin Kelly <martin@martingkelly.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Martin Kelly authored
Update the sensor settings to support the LSM9DS1 sensor. Although the LSM9DS1 accelerometer and gyroscope are coupled together to use the same FIFO, the magnetometer is separate and can be cleanly supported without refactoring the existing driver. Signed-off-by: Martin Kelly <martin@martingkelly.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Martin Kelly authored
Add a comment clarifying better when to use <device_name> vs <device_name>-magn in compatibility strings. Signed-off-by: Martin Kelly <martin@martingkelly.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matt Ranostay authored
More concise to have a pointer to tpl0102_cfg struct in the iio_priv data than an integer to an index of an array. Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Reviewed-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 03 Nov, 2018 7 commits
-
-
Charles-Antoine Couret authored
Description how to invoke ad7949 driver from device tree file. Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Charles-Antoine Couret authored
Compatible with AD7682 and AD7689 chips. It is a Analog Devices ADC driver 14/16 bits 4/8 channels with SPI protocol Datasheet of the device: http://www.analog.com/media/en/technical-documentation/data-sheets/AD7949.pdfSigned-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Victor Colombo authored
This patch fixes the checkpatch.pl warning: WARNING: Blank lines aren't necessary before a close brace '}' Signed-off-by: Victor Colombo <victorcolombo@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Victor Colombo authored
This patch fixes the checkpatch.pl warning: WARNING: No space is necessary after a cast Signed-off-by: Victor Colombo <victorcolombo@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Dan O'Donovan authored
This updates the ti-adc128s052.c file to use SPDX-License-Identifier instead of more verbose license text. Signed-off-by: Dan O'Donovan <dan@emutex.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nicola Lunghi authored
ACPI _HID AANT1280 matches an ADC124S101 present on E3940 SKUs of the UP Squared board. Add it to the driver. Signed-off-by: Nicola Lunghi <nicola.lunghi@emutex.com> [javier@emutex.com: fix up commit message and one checkpatch warning] Signed-off-by: Javier Arteaga <javier@emutex.com> Signed-off-by: Dan O'Donovan <dan@emutex.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Javier Arteaga authored
The datasheets for ADC122S021 and ADC124S021 list two more pin-compatible alternatives for each device. Add their IDs as compatible strings. Suggested-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Javier Arteaga <javier@emutex.com> Signed-off-by: Dan O'Donovan <dan@emutex.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 21 Oct, 2018 7 commits
-
-
Nishad Kamdar authored
Use the gpiod interface for rdwr_pin, convert_pin and busy_pin instead of the deprecated old non-descriptor interface. Note that Phil Reid identified that some of this code would never have worked. A follow up patch can fix that as this is just a direct change of interface. Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Colin Ian King authored
Static analysis with CoverityScan is throwing warnings that specific case statements are missing breaks. Rather than adding breaks, add return -EINVAL to the specific case statements to clarify the error return paths. Fix also saves 50 bytes. Before: text data bss dec hex filename 21418 4936 128 26482 6772 drivers/iio/adc/ina2xx-adc.o After: dec hex filename 21370 4936 128 26434 6742 drivers/iio/adc/ina2xx-adc.o (gcc 8.2, x86-64) Detected by CoverityScan, CID#1462408 ("Missing break in switch") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Marcelo Schmitt authored
Change close parenthesis alignment to match respective open parenthesis at iio/drivers/staging/iio/adc/ad7606.c line 379. This makes the file more compliant with the preferred coding style for the linux kernel. Signed-of-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Martin Kelly authored
Miscellaneous cleanup to fix minor consistency, grammar, and spelling issues. Signed-off-by: Martin Kelly <martin@martingkelly.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Slawomir Stepien authored
The custom build function ad7280_crc8_build_table is not needed. The crc8_populate_msb function from linux/crc8.h will build the same crc table. Signed-off-by: Slawomir Stepien <sst@poczta.fm> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Slawomir Stepien authored
Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative error code. This change will ensure that this error is being passed up in the call stack, so it can be handled. Signed-off-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Jiri Olsa authored
So user could specify outside CFLAGS values. Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 14 Oct, 2018 3 commits
-
-
Hans de Goede authored
Add KIOX0009 ACPI HID, this is used e.g. on the Acer One 10. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Renato Lui Geh authored
This patch fixes most "Alignment should match open parenthesis" check warnings found by checkpatch.pl in the addac/adt7316 driver. Signed-off-by: Renato Lui Geh <renatogeh@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Notice that in this particular case, I replaced "...and fall through." with the specific string "fall through", which is what GCC is expecting to find thus supressing this false positive. As Peter has observed this breaks the nice English flow, which is less than ideal, but short of teaching GCC to read English, there isn't a lot that we can do about it. Addresses-Coverity-ID: 1462408 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 08 Oct, 2018 1 commit
-
-
Matheus Tavares authored
This patch fixes all "Assignment operator '=' should be on the previous line" checks found in ad2s1210.c with checkpatch.pl. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 07 Oct, 2018 2 commits
-
-
Slawomir Stepien authored
These lines were misaligned, but the checkpatch.pl didn't indicate them as such. Signed-off-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Slawomir Stepien authored
By using the copy of channel attribute, we can now make the lines short enough to eliminate the checkpatch.pl problem: CHECK: Alignment should match open parenthesis Signed-off-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-