- 19 Apr, 2013 7 commits
-
-
Patrick McHardy authored
- macvlan: propagate STAG filtering capabilities from underlying device - ifb: announce STAG tagging support in addition to CTAG tagging support - veth: announce STAG tagging/stripping support in addition to CTAG support Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Patrick McHardy authored
Add support for 802.1ad VLAN devices. This mainly consists of checking for ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check offloading capabilities based on the used protocol. Configuration is done using "ip link": # ip link add link eth0 eth0.1000 \ type vlan proto 802.1ad id 1000 # ip link add link eth0.1000 eth0.1000.1000 \ type vlan proto 802.1q id 1000 52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64 92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84) 20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64 Signed-off-by: -
Patrick McHardy authored
Add a protocol argument to the VLAN packet tagging functions. In case of HW tagging, we need that protocol available in the ndo_start_xmit functions, so it is stored in a new field in the skb. The new field fits into a hole (on 64 bit) and doesn't increase the sks's size. Signed-off-by:
-
Patrick McHardy authored
Make the encapsulation protocol value a property of VLAN devices and change the device lookup functions to take the protocol value into account. Signed-off-by:
-
Patrick McHardy authored
Change the rx_{add,kill}_vid callbacks to take a protocol argument in preparation of 802.1ad support. The protocol argument used so far is always htons(ETH_P_8021Q). Signed-off-by: -
Patrick McHardy authored
Rename the hardware VLAN acceleration features to include "CTAG" to indicate that they only support CTAGs. Follow up patches will introduce 802.1ad server provider tagging (STAGs) and require the distinction for hardware not supporting acclerating both. Signed-off-by:
-
David S. Miller authored
Jeff Kirsher says: ==================== This series contains updates to ixgbe and igb. The ixgbe changes contains 2 patches from the community, one which is a fix from akepner to fix a issue where netif_running() in shutdown was not done under rtnl_lock. The other community fix from Joe Perches cleans up #ifdef CONFIG_DEBUG_FS which is no longer necessary. The last ixgbe patch, from Jacob Keller, adds support for WoL on 82559 SFP+ LOM. The remaining patches are against igb, 10 of which were previously submitted in a pull request where changes were requested. The following igb patches: igb: Support for 100base-fx SFP igb: Support to read and export SFF-8472/8079 data are v2 based on feedback from Dan Carpenter and Ben Hutchings in the previous pull request. The largest set of changes are in my patch to cleanup code comments and whitespace to align the igb driver with the networking style of code comments. While cleaning up the code comments, fixed several other whitespace/checkpatch.pl code formatting issues. Other notable igb patches are EEE capable devices query the PHY to determine what the link partner is advertising, added support for i354 devices and added support for spoofchk config. ==================== Signed-off-by:
-
- 18 Apr, 2013 27 commits
-
-
Carolyn Wyborny authored
This patch adds base support for new i354 devices. Loopback test is unsupported for this release. Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Lior Levy authored
Add support for spoofchk configuration per VF via iproute2 tool. Signed-off-by:
Lior Levy <lior.levy@intel.com> Tested-by:
Sibai Li <sibai.li@intel.com> Signed-off-by:
-
Matthew Vick authored
On EEE-capable devices, query the PHY to determine what the link partner is advertising. Signed-off-by:
Matthew Vick <matthew.vick@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Jeff Kirsher authored
Aligns the multi-line code comments with the desired style for the networking tree. Also cleaned up whitespace issues found during the cleanup of code comments (i.e. remove unnecessary blank lines, use tabs where possible, properly wrap lines and keep strings on a single line) Signed-off-by:
-
Akeem G. Abodunrin authored
This patch fixes sparse warnings on function pointers that are not defined as static. Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by:
-
Alexander Duyck authored
It turns out that the InterruptThrottleRate module parameter was only having the effect of locking the ITR at the starting ITR value. This was because the values stored in rx_itr_setting and tx_itr_setting were being ignored when configuring the initial itr_val of the q_vector. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Alexander Duyck authored
We only need the adapter pointer in the case of ptp. As such we can pull the adapter out of the main path and place it inside the if statement to avoid the temptation of accessing the adapter pointer in the fast path. Signed-off-by:
-
Alexander Duyck authored
We were incorrectly checking the entire frag_off field when we only wanted the fragment offset. As a result we were not pulling in TCP headers when the DNF flag was set. To correct that we will now check for frag off using the IP_OFFSET mask. Signed-off-by:
-
Akeem G. Abodunrin authored
This patch fixes code and comments as identified in the driver. Signed-off-by:
-
Akeem G. Abodunrin authored
Based on original patch from Aurélien Guillaume <footplus@gmail.com> This patch adds support to turn on I2C, with sfp cage powered. CC: Aurélien Guillaume <footplus@gmail.com> Signed-off-by:
-
Akeem G. Abodunrin authored
This patch adds support to read and export SFF-8472/8079 (SFP data) over i2c, through Ethtool. v2: Changed implementation to accommodate any offset within SFF module length boundary. Reported-by:Aurélien Guillaume <footplus@gmail.com> CC: Aurélien Guillaume <footplus@gmail.com> CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Akeem G. Abodunrin authored
This patch adds support for 100base-fx SFP and report proper link speed/duplex via Ethtool. v2: fix smatch warnings CC: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Joe Perches authored
Add some empty static inlines instead to make the code more readable. Signed-off-by:
Joe Perches <joe@perches.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
-
Jacob Keller authored
This patch adds software support for WoL for the 82599 SFP+ LOM device, (ID 0x8976) Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
akepner authored
During shutdown it's possible for __dev_close() (which holds rtnl_lock) to clear the __LINK_STATE_START bit, and for ixgbe to then read that bit (without holding rtnl_lock), and then not fail to free irqs, etc. The result is a crash like this: ------------[ cut here ]------------ kernel BUG at drivers/pci/msi.c:313! invalid opcode: 0000 [#1] SMP last sysfs file: /sys/devices/system/cpu/cpu3/cache/index2/shared_cpu_map CPU 1 Pid: 5910, comm: reboot Tainted: P ---------------- 2.6.32 #1 empty RIP: 0010:[<ffffffff81305c2b>] [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130 RSP: 0018:ffff880185c9bc88 EFLAGS: 00010282 RAX: ffff880219f58bc0 RBX: ffff88021ac53b00 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000246 RDI: 000000000000004a RBP: ffff880185c9bcc8 R08: 0000000000000002 R09: 0000000000000106 R10: 0000000000000000 R11: 0000000000000006 R12: ffff88021e524778 R13: 0000000000000001 R14: ffff88021e524000 R15: 0000000000000000 FS: 00007f90821b7700(0000) GS:ffff880028220000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007f90818bd010 CR3: 0000000132c64000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process reboot (pid: 5910, threadinfo ffff880185c9a000, task ffff88021bf04a80) Stack: ffff880185c9bc98 000000018130529d ffff880185c9bcc8 ffff88021e524000 <0> 0000000000000004 ffff88021948c700 0000000000000000 ffff880185c9bda7 <0> ffff880185c9bce8 ffffffff81305cbd ffff880185c9bce8 ffff88021948c700 Call Trace: [<ffffffff81305cbd>] pci_disable_msix+0x3d/0x50 [<ffffffffa00501d5>] ixgbe_reset_interrupt_capability+0x65/0x90 [ixgbe] [<ffffffffa00512f6>] ixgbe_clear_interrupt_scheme+0xb6/0xd0 [ixgbe] [<ffffffffa005330b>] __ixgbe_shutdown+0x5b/0x200 [ixgbe] [<ffffffffa00534ca>] ixgbe_shutdown+0x1a/0x60 [ixgbe] [<ffffffff812f6c7c>] pci_device_shutdown+0x2c/0x50 [<ffffffff813727fb>] device_shutdown+0x4b/0x160 [<ffffffff8107d98c>] kernel_restart_prepare+0x2c/0x40 ehci timer_action, mod_timer io_watchdog [<ffffffff8107d9e6>] kernel_restart+0x16/0x60 [<ffffffff8107dbfd>] sys_reboot+0x1ad/0x200 [<ffffffff811676cf>] ? __d_free+0x3f/0x60 [<ffffffff81167748>] ? d_free+0x58/0x60 [<ffffffff8116f7c0>] ? mntput_no_expire+0x30/0x100 [<ffffffff81152b11>] ? __fput+0x191/0x200 [<ffffffff816565fe>] ? do_page_fault+0x3e/0xa0 [<ffffffff8100b132>] system_call_fastpath+0x16/0x1b Code: 4c 89 ef e8 98 8c e3 ff 4d 39 f4 48 8b 43 10 75 cf 48 83 c4 18 5b 41 5c 41 5d 41 5e 41 5f c9 c3 49 8b 7d 20 e8 07 5a d3 ff eb c9 <0f> 0b 0f 1f 00 eb fb 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 ehci timer_action, mod_timer io_watchdog RIP [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130 RSP <ffff880185c9bc88> ---[ end trace 27de882a0fe75593 ]--- (This was seen on a pretty old kernel/driver, but looks like the same bug is still possible.) Signed-off-by: <akepner@riverbed.com> Tested-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== This series contains updates to ixgbe only. v2- Dropped the following 2 patches from the series: ixgbe: Support using build_skb in the case that jumbo frames are disabled ixgbe: walk pci-e bus to find minimum width Ben Hutchings found a bug with Alex's patch, so that patch was dropped permanently. Jacob's "walk PCIe bus" patch is being re-worked for a more generic solution so that other drivers can benefit. In the remaining patches... Alex provides a fix where we were incorrectly checking the entire frag_off field when we only wanted the fragment offset. Alex also cleans up the check for PAGE_SIZE, since the default configuration allocates 32K for all buffers. Emil provides a change to the calculation of eerd so that it is consistent between the read and write functions by using | instead of +. Jacob adds support for displaying PCIe Gen3 link speed, which was previously missing from the ixgbe driver. He also provides a patch to clean up ixgbe_get_bus_info_generic to call some conversion functions, which are used also in another patch provided by Jacob. Jacob modifies the driver to enable certain devices (which have an internal switch) to read from the physical slot rather than reading data from the internal switch. Don provides a couple of fixes (which are more appropriate for net-next), one of which resolves an issue where ixgbe was only turning on the laser when the adapter was up which caused issues for those who wanted to access the MNG firmware while the port was in a down state. The other fix is for WoL when currently linked at 1G. Lastly Don bumps the driver version keep the in-kernel driver up to date with the current functionality. ==================== Signed-off-by: -
Eric Dumazet authored
Host queues (Qdisc + NIC) can hold packets so long that TCP can eventually retransmit a packet before the first transmit even left the host. Its not clear right now if we could avoid this in the first place : - We could arm RTO timer not at the time we enqueue packets, but at the time we TX complete them (tcp_wfree()) - Cancel the sending of the new copy of the packet if prior one is still in queue. This patch adds instrumentation so that we can at least see how often this problem happens. TCPSpuriousRtxHostQueues SNMP counter is incremented every time we detect the fast clone is not yet freed in tcp_transmit_skb() Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Fabio Estevam authored
There is nothing in the driver that requires <asm/coldfire.h> and <asm/mcfsim.h>. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Don Skidmore authored
Bump the version number reflect the corresponding functionality in the out of tree driver. Signed-of-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
-
Don Skidmore authored
We reset during the shutdown path which will reset AUTOC register. This would change LMS to 10G. If we were currently linked at 1G we will lose link, which is a bad thing if we wanted WoL to work. For the fix I needed to know if WoL is supported so I created a new bool in the ixgbe_hw struct. If this is set we will not allow the reset to change the current LMS value in AUTOC. Signed-off-by:
-
Don Skidmore authored
We were only turning the laser on when the adapter was up. This causes issues for those who wanted to access the MNG FW while the port was in a down state. This patch makes sure the laser is turned on in probe and remain up even after the port is brought down. Signed-off-by:
-
Jacob Keller authored
This patch modifies the driver to enable certain devices, which have an internal switch, to read data from the physical slot rather than reading data from the internal switch. The internal switch will always report the same PCI width and speed, which is not useful compared to knowing the width and speed of the slot the physical card is plugged into. Signed-off-by:
-
Jacob Keller authored
This patch cleans up ixgbe_get_bus_info_generic to call some conversion functions, which are used also in a follow on patch that needs to convert between the link_status PCIe config values into ixgbe's internal enum representations. Signed-off-by:
-
Jacob Keller authored
This patch adds support for displaying PCIe Gen3 link speed, which was previously missing from the driver. Signed-off-by:
-
Alexander Duyck authored
The check for PAGE_SIZE is pointless now that the default configuration is to allocate 32K for all buffers. Since the Tx descriptor limit is 16K we can just drop the check and always compare the descriptors to the maximum size supported. Signed-off-by:
-
Emil Tantilov authored
Make the calculation of eerd consistent between the read and write functions by using | instead of + for IXGBE_EEPROM_RW_REG_START Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
Alexander Duyck authored
We were incorrectly checking the entire frag_off field when we only wanted the fragment offset. As a result we were not pulling in TCP headers when the DNF flag was set. To correct that we will now check for frag off using the IP_OFFSET mask. Signed-off-by:
-
- 17 Apr, 2013 6 commits
-
-
David S. Miller authored
Patrick McHardy says: ==================== The following patchset adds support for running TIPC over InfiniBand. The patchset consists of three parts (+ a minor fix for the ethernet media type): - Preparation: removal of an the unused str2addr callback and move of the bcast_addr from struct tipc_media to struct tipc_bearer. This is necessary because InfiniBand doesn't have a fixed broadcast address like ethernet, so it needs to be initialized with the device's broadcast address when the bearer is enabled - Introduction of a TIPC InfiniBand media type. A new media type is needed to deal with the different address sizes - Support for ETH_P_TIPC in IPoIB Since the last posting I've addressed all feedback I received and rebased to the current net-next tree. I consider these patches ready for merging. Since they mainly affect TIPC code, I'd propose to have them either go through the TIPC tree or through Dave directly (not sure how TIPC patches are managed). ==================== Signed-off-by: -
Patrick McHardy authored
Support TIPC in the IPoIB driver. Since IPoIB now keeps track of its own neighbour entries and doesn't require the packet to have a dst_entry anymore, the only necessary changes are to: - not drop multicast TIPC packets because of the unknown ethernet type - handle unicast TIPC packets similar to IPv4/IPv6 unicast packets in ipoib_start_xmit(). An alternative would be to remove all ethertype limitations since they're not necessary anymore, all TIPC needs to know about is ARP and RARP since it wants to always perform "path find", even if a path is already known. Signed-off-by:
-
Patrick McHardy authored
Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: -
Patrick McHardy authored
The skb->protocol field is used by packet classifiers and for AF_PACKET cooked format, TIPC needs to set it properly. Fixes packet classification and ethertype of 0x0000 in cooked captures: Out 20:c9:d0:43:12:d9 ethertype Unknown (0x0000), length 56: 0x0000: 5b50 0028 0000 30d4 0100 1000 0100 1001 [P.(..0......... 0x0010: 0000 03e8 0000 0001 20c9 d043 12d9 0000 ...........C.... 0x0020: 0000 0000 0000 0000 ........ Signed-off-by:
-
Patrick McHardy authored
Some network protocols, like InfiniBand, don't have a fixed broadcast address but one that depends on the configuration. Move the bcast_addr to struct tipc_bearer and initialize it with the broadcast address of the network device when the bearer is enabled. Signed-off-by:
-
Patrick McHardy authored
Signed-off-by:
-
