- 18 May, 2010 40 commits
-
-
Mauro Carvalho Chehab authored
Signed-off-by:Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Change the ir-sysfs approach to create irrcv0 as a device, instead of using class_dev. Also, change the way input is registered, in order to make its parent to be the irrcv device. Due to this change, now the event device is created under /sys/class/ir/irrcv class: /sys/class/irrcv/irrcv0/ |-- current_protocol |-- device -> ../../../1-3 |-- input9 | |-- capabilities | | |-- abs ... Signed-off-by: -
Stefan Ringel authored
-add Hauppauge WinTV HVR 900H/WinTV USB2-Stick vid/pid 0x2040/6601 0x2040/6610 0x2040/6611 -add Terratec Cinergy Hybrid-Stick vid/pid 0x0ccd/0x00a5 -add Twinhan TU501(704D1) vid/pid 0x13d3/0x3240 0x13d3/0x3241 0x13d3/0x3243 0x13d3/0x3264 Signed-off-by:
Stefan Ringel <stefan.ringel@arcor.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Max Thrun authored
Signed-off-by:
Max Thrun <bear24rw@gmail.com> Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
Jean-François Moine <moinejf@free.fr> Signed-off-by:
-
Mosalam Ebrahimi authored
Note that setting this options to 50Hz can reduce the framerate, so it is still disabled (60Hz) by default. Signed-off-by:
Mosalam Ebrahimi <m.ebrahimi@ieee.org> Signed-off-by:
-
Antonio Ospite authored
* Indent with tabs, not with spaces, nor with mixed style. * Less indentation for controls index comments. * Use lowercase hex digits. Signed-off-by:
-
Max Thrun authored
Also set default values unconditionally, for readability. Signed-off-by:
-
Max Thrun authored
* Adjust comments for sharpness control * Set default value unconditionally, for readability Signed-off-by:
-
Max Thrun authored
Set only the needed bits for AWB, and enable it by default. Signed-off-by:
-
Antonio Ospite authored
Document that even if the state is a u8 value, both MSB and LSB are set as sd->exposure represents half of the value we are going to set into registers. Skip setting exposure when AEC is enabled. Signed-off-by:
-
Max Thrun authored
This also makes manual exposure actually work: it never worked before because AEC was always enabled. Signed-off-by:
-
Max Thrun authored
* Use 'agc' instead of 'autogain' in the code so to align the naming as in AEC/AWB. * Tweak brightness and contrast default values. * Fix setting/resetting registers values for AGC. * Set actual gain back when disabling AGC. * Skip setting GAIN register when AGC is enabled. * Enable AGC by default. Note that as Auto Gain Control is now enabled by default, if you are using the driver for visual computing applications you might need to disable it explicitly in your software. Signed-off-by: -
Antonio Ospite authored
Hue control doesn't work and the sensor datasheet is not clear about how to set hue properly. Signed-off-by:
-
Max Thrun authored
Remove Blue/Red Channel Target Value, they are meant for Black Level Calibration but it is not completely clear how to use them. Signed-off-by:
-
Oliver Endriss authored
Add support for - Linux4Media cineS2 DVB-S2 Twin Tuner (v5) - Mystique SaTiX-S2 Dual (v2) Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Julia Lawall authored
The region set by the call to memset is immediately overwritten by the subsequent call to memcpy. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e1,e2,e3,e4; @@ - memset(e1,e2,e3); memcpy(e1,e4,e3); // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Cc: Manu Abraham <abraham.manu@gmail.com> Signed-off-by:
-
Manu Abraham authored
Signed-off-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
Andreas Regel authored
V4L/DVB: Budget/STV090x/STV6110x: Initialize the demodulator immediately after the tuner is attached Signed-off-by:
Andreas Regel <andreas.regel@gmx.de> Signed-off-by:
-
Manu Abraham authored
Signed-off-by:
-
Manu Abraham authored
Oliver Endriss <o.endriss@gmx.de> pointed out: Imho not a good idea, as the frontend thread calls - fe->ops.tuner_ops.init - fe->ops.tuner_ops.sleep If you remove fe->ops.i2c_gate_ctrl, init and sleep will fail, because gate_ctrl was never called... -- Signed-off-by:
Manu Abraham <manu@gmail.com> Signed-off-by:
-
Manu Abraham authored
- Remove a redundant exported gate control function Signed-off-by:
-
Oleg Roitburd authored
Also add in some more device ID's Signed-off-by:
Oleg Roitburd <oroitburd@gmail.com> Signed-off-by:
-
Oleg Roitburd authored
Signed-off-by:
-
Ian Armstrong authored
Since the change that stops the CX23415/6 firmware-intiiated secondary stream appears to fix the temporal filter, it's now fully re-enabled for all capture resolutions. Signed-off-by:
Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by:
Andy Walls <awalls@radix.net> Signed-off-by:
-
Ian Armstrong authored
When a capture is started, the firmware also appears to start a secondary stream. Unless this secondary stream is also stopped, the encoder will remain active and not reinitialise for the next capture. Unfortunately, setting up the video source can glitch the encoder and result in undesirable effects that this initialisation will clear. Signed-off-by:
-
Andy Walls authored
Combine the two 150 ms delays into a single 300 ms delay. Ian Armstrong has noted that the delay between CX2341X_ENC_INITIALIZE_INPUT and CX2341X_ENC_START_CAPTURE can cause problems if the temporal filter is allowed to be enabled. Signed-off-by:
-
Abylay Ospan authored
IRQ from CAM disabled by default. In some environment enabled IRQ can cause of machine freeze. Signed-off-by:
Abylay Ospan <aospan@netup.ru> Signed-off-by:
-
Abylay Ospan authored
Signed-off-by:
-
Antti Palosaari authored
Add USB ID 1b80:e39a for KWorld TV Stick II (395UR). Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Add USB ID 1b80:e383 for KWorld USB DVB-T Stick Mobile (UB383-T). Signed-off-by:
-
Dean Anderson authored
adds hardware frame skipping using VIDIOC_S_PARM ioctl. adds support for VIDIOC_ENUM_FRAMEINTERVALS. Signed-off-by:
Dean Anderson <dean@sensoray.com> Signed-off-by:
-
Márton Németh authored
Make the local functions static. Note that the function command_setlights() is currently not called from anywhere. This will remove the following sparse warnings (see "make C=1"): * symbol 'command_setformat' was not declared. Should it be static? * symbol 'command_setcolourparams' was not declared. Should it be static? * symbol 'command_setapcor' was not declared. Should it be static? * symbol 'command_setvloffset' was not declared. Should it be static? * symbol 'command_setexposure' was not declared. Should it be static? * symbol 'command_setcolourbalance' was not declared. Should it be static? * symbol 'command_setcompressiontarget' was not declared. Should it be static? * symbol 'command_setyuvtresh' was not declared. Should it be static? * symbol 'command_setcompressionparams' was not declared. Should it be static? * symbol 'command_setcompression' was not declared. Should it be static? * symbol 'command_setsensorfps' was not declared. Should it be static? * symbol 'command_setflickerctrl' was not declared. Should it be static? * symbol 'command_setecptiming' was not declared. Should it be static? * symbol 'command_pause' was not declared. Should it be static? * symbol 'command_resume' was not declared. Should it be static? * symbol 'command_setlights' was not declared. Should it be static? Signed-off-by:
Márton Németh <nm127@freemail.hu> Signed-off-by:
-
Dmitri Belimov authored
Fix broken I2C IR for TV cards of Beholder. Signed-off-by:
Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by:
-
Dean Anderson authored
2257 is 2255 with 2 svideo inputs Signed-off-by:
-
Dean Anderson authored
Signed-off-by:
-
Dean Anderson authored
s2255drv fixes for big endian architecture Signed-off-by:
-
Antonio Larrosa authored
This patch adapts the changes submitted by Dainius Ridzevicius to the linux-media mailing list on 8/14/09, to the current sources in order to make the Kworld VS-DVB-T 323UR usb device work. I also removed the "not validated" flag since I own the device and validated that it works fine after the patch is applied. Thanks to Devin Heitmueller for his guidance with the code. Signed-off-by:
Antonio Larrosa <larrosa@kde.org> Acked-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Dean Anderson authored
Video status capability for inputs on Sensoray 2255 driver. Signed-off-by:
-
Dmitri Belimov authored
Add defines for all registers of the tm6000 module. This defines made by doc for TM6010, need look docs for TM6000 and TM5600 Some registers can be different. Signed-off-by:
-
