Currently the driver loads and unloads all reps in an unbreakable
group. However, with ECPF, the reps of special vports such as uplink
and host PF should always be loaded in switchdev mode where the reps
for VFs will be loaded on-demand and unloaded on no-demand. This is
a pre-step for that change.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.

Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:

	create: (none)       -> unregistered
	reg:    unregistered -> registered
	load:   registered   -> loaded
	unload: loaded       -> registered
	unreg:  registered   -> unregistered

Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With only PF and VF, it is sufficient to have the vport/rep array
index as the vport number. This is because PF and VF vports numbers
are consecutive serial numbers. In downstream patches with
introducing of ECPF and UPLINK vports, it's not consecutive any more.

Use getter to get specific vport/rep, and use iterator to traversal
a list of vport/rep. This hides the translation between array index
and vport number, and provides flexibility of using different
translation mechanism in the future.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.

With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).

Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

E-switch offloads mode initialize/cleanup multiple steering related
entities (flow table/group). Refactor these operations to internal
helper functions for better block design.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Commands referring to vports use the following scheme:

1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
   referred vport and put 1 in other_vport. It was assumed that driver
   is accessing other vport when vport number is greater than 0.

With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.

As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When bonding is added, driver assumes that it's RoCE LAG if no VF is
enabled. This is not enough for ECPF as the VF is enabled in host PF
side. LAG should only choose RoCE mode when both slave devices meet
conditions below:
 1. E-Switch offloads mode is NONE.
 2. No VF is enabled.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Merge mlx5-next shared branched into net-next,

From Bodong Wang:
1) Introduction of ECPF (Embedded CPU Physical Function), and low level
bits for mlx5 SmartNic capabilities support.
2) Vport enumeration refactoring that affect mlx5_ib and mlx5_core

From Aya Levin,
3) Add support for 50Gbps per lane link modes in the Port Type and Speed
register (PTYS)
4) Refactor low level query functions for PTYS register
5) Add support for 50Gbps per lane link modes to mlx5_ib

Note: due to a change in API in mlx5/core and a later patch from net-next,
a fixup was squashed with this merge commit that replaces FDB_UPLINK_VPORT
with MLX5_VPORT_UPLINK which exists only in upstream net-next.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Driver now supports new link modes: 50Gbps per lane support for
50G/100G/200G. This patch reads the correct field (legacy vs. extended)
based on a FW indication bit, and adds a translation function (link
modes to IB width and speed) to the new link modes.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch exposes new link modes (including 50Gbps per lane), and ext_*
fields which describes the new link modes in Port Type and Speed
register (PTYS).
Access functions, translation functions (speed <-> HW bits) and
link max speed function were modified.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Register Port Type and Speed (PTYS) introduces three new fields
extending the speed/protocols the can be reported and configured.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch fascicles queries to speed related fields in Port Type and
Speed register (PTYS) into a single API. I addition, this patch
refactors functions which serves only Ethernet driver: remove the
protocol type as an input parameter, move code from 'core' directory
into 'en' directory and add 'eth' prefix to the function's name. The
patch also encapsulates functions that are not used outside the Ethernet
driver removes redundant include files.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When dealing with the offloads mode initialization, driver refers to
the number of VFs and add magic number one (1) to take account of the
uplink. This is not clear and will make the code less readable after
adding other vports (e.g. host PF). As these are special vports
compared to VF vports, add a helper macro to denote such special
vports and eliminate the use of magic number.

Moreover, when creating offloads flow table and groups, the driver
reserves two more slots for UC and MC miss rules. Replace this magic
number with a helper macro as well.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

These are two macros in the driver general header which deal with the
number of total vports and if a vport is vport manager. Such macros
are vport entities, better to place them at the vport header file.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Driver used to name uplink vport as FDB_UPLINK_VPORT, it's hard to
comply with the same naming convention along with the introduction of
other vports. Use MLX5_VPORT as the prefix for such vports and
relocate the uplink vport definition to public header file for the
benefits of both net and IB drivers.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

ECPF doesn't support SR-IOV, but an ECPF E-Switch manager shall know
the max VFs supported by its peer host PF in order to control those
VF vports.

The current driver implementation uses the total vfs quantity as
provided by the pci sub-system for an upper bound of the VF vports
the e-switch code needs to deal with. This obviously can't work as
is on ECPF e-switch manager. For now, we use a hard coded value of
128 on such systems.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.

Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.

The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With the introduction of ECPF, we require that the ECPF driver will
aways call enable/disable HCA for that PF in the same way a PF does
this for its VFs. The PF is still responsible for calling enable and
disable HCA for its VFs.

To distinguish between the ECPF executing enable/disable HCA for
itself or for the PF, it sets the embedded CPU function bit in the
input params struct of these commands. When the bit is cleared and
function ID is zero, it refers to the peer PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.

With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.

When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.

The encoding before this patch was as follows:
    function_id == 0: pages are requested for the function receiving
                      the EQE.
    function_id != 0: pages are requested for VF identified by the
                      function_id value

A new one bit field in the EQE identifies that pages are requested for
the ECPF.

The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:

1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function

This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

IB driver maintains different registration and load function calls
for uplink and VF vports. This is not necessary as they only differ
with each other on their profiles.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use u16 for vport number, which matches how hardware refers to this
argument throughout commands.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Better to use void * and avoid unnecessary casts.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

After failing to allocate a receive buffer the driver may fail to ever
request additional allocations. EF10 NICs require new receive buffers to
be pushed in batches of eight or more. The test for whether a slow fill
should be scheduled failed to take account of this. There is little
downside to *always* requesting a slow fill if we failed to allocate a
buffer, so the condition has been removed completely. The timer that
triggers the request for a refill has also been shortened.
Signed-off-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in intr_handler() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in arc_emac_tx_clean() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible that there might be an originally parent object with 0
direct users that is in hints no longer considered as parent. Then the
weight of this object is 0 and current code ignores him. That's why the
total amount of hint objects might be lower than for the original
objagg and WARN_ON is hit. Fix this be considering 0 weight valid.

Fixes: 9069a381 ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vishal Kulkarni says:

====================
cxgb4/cxgb4vfSupport for SGE doorbell queue timer

This series of patchs add SGE doorbell queue timer for faster DMA completions.

Patch 1 Implements SGE doorbell queue timer

Patch 2 Adds ethtool capability to set/get SGE doorbell queue timer tick

v2
- Reverse christmas tree formatting for local variables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch gets/sets SGE Doorbell Queue timer ticks via ethtool

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

T6 introduced a Timer Mechanism in SGE called the
SGE Doorbell Queue Timer. With this we can now configure
TX Queues to get CIDX Updates when:

    Time(CIDX == PIDX) >= Timer

Previously we rely on TX Queue Status Page updates by hardware
for DMA completions. This will make Hardware/Firmware actually
deliver the CIDX Updates as Ingress Queue messages with
commensurate Interrupts.

So we now have a new RX Path component for processing CIDX Updates
and reclaiming TX Descriptors faster.

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb should be freed by dev_consume_skb_any() in efx_tx_tso_fallback()
when skb is still used. The skb will be replaced by segments, so the
original skb should be consumed(not drop).
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb should be freed by dev_consume_skb_any() in macb_pad_and_fcs()
when *skb is still used. The *skb is be replaced by nskb, so the
original *skb should be consumed(not drop).
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called when skb xmit
done.It makes drop profiles more friendly.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

modify the code style in order to removing the following warning
when excute the script checkpatch.pl
WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb should be freed by dev_consume_skb_any() in hfcpci_fill_fifo()
when bcs->tx_skb is still used. The bcs->tx_skb is be replaced by
skb_dequeue(&bcs->squeue), so the original bcs->tx_skb should
be consumed(not drop).
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>