ACLK_VIO is the noc bus clock for display module, display cann't
read data from ddr without this clock enabled.

Due to it shouldn't belong to any driver, but we need it enabled,
so just mark it as the CLK_IGNORE_UNUSED flag.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Reference the newly added efuse clock-ids in the clock-tree.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the clock tree definition for the new rk3228 SoC.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the devicetree binding for the cru on the rk3228 which quite similar
structured as previous clock controllers.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add clock-ids for the two efuse blocks of the rk3288.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the dt-bindings header for the rk3228, that gets shared between
the clock controller and the clock references in the dts.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

RK3228's armclk has 3 parents, so allow cpuclk to have
more than 2 parents.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Due to a copy-paste error the the rk3368 cpuclk settings were acessing
rk3288-specific register offsets. This never caused problems till now,
as cpu frequency scaling in't used currently at all.
Reported-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add aclk_bus and aclk_peri to the list of rk3368 critical clocks,
which are the base clocks that supply for all peripherals, never
to be disabled automatically.
Signed-off-by: Jianqun xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Most rk3368 boards (especially those with Pmic that followed the lead
from rk3368-evb-act8846) have a PWM regulator on them for vdd_logic.
This is the main voltage for all kinds of misc stuff including the
memory controller.

On these boards it is critically important to make sure that the PWM
never ever glitches and never loses its clock. Any glitch could
crash the system.

Right now there are no users of the PWM regulator and also Linux
thinks that the PWM regulator is disabled.  Things happen to work
because firmware configured the PWM and Linux doesn't touch it.
..and the PWM's clock is marked as "ignore unused".

...but things _stop_ working if we turn off serial console.  Why?
Because:
    1. Serial console shares a parent clock with the PWM (pclk_cpu)
    2. If we have no serial console then nobody is holding pclk_cpu on
       at reboot time.  It gets disabled.

We need to fix a lot of the above problems, but until we get
everything right the cleanest "hack" seems like it is to just keep
the "rk_pwm" clock on always.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

We've been seeing some crashes at reboot test on rk3288-based systems,
which boards have not reset pin connected to NPOR, they reboot by
setting 0xfdb9 to RK3288_GLB_SRST_FST register. If the APLL works in
a high frequency mode, some IPs might hang during soft reset.
It appears that we can fix the problem by switching to slow mode before
reboot, just like what we did before suspend.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

sclk_mipidsi_24m is the gating of mipi dsi phy.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Adds a new id for the sclk supplying the mipidsi on rk3288 socs.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the clock tree definition for the new rk3036 SoC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The rk3036's pll and clock are different with base on the rk3066(rk3188,
rk3288, rk3368 use it), there are different adjust foctors and control
registers, so these should be independent and separate from the series
of rk3066s.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the devicetree binding for the cru on the rk3036 which quite similar
structured as previous clock controllers.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Set the newly added id for the crypto clk, so that it can be called
in other parts.
Signed-off-by: Zain Wang <zain.wang@rock-chips.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the dt-bindings header for the rk3036, that gets shared between
the clock controller and the clock references in the dts.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add an id for crypto clk to the binding header, so that it can be called
in other part.
Signed-off-by: Zain Wang <zain.wang@rock-chips.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Pull perf updates from Thomas Gleixner:
 "Mostly updates to the perf tool plus two fixes to the kernel core code:

   - Handle tracepoint filters correctly for inherited events (Peter
     Zijlstra)

   - Prevent a deadlock in perf_lock_task_context (Paul McKenney)

   - Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
     Melo)

   - Print full source file paths when using 'perf annotate --print-line
     --full-paths' (Michael Petlan)

   - Fix 'perf probe -d' when just one out of uprobes and kprobes is
     enabled (Wang Nan)

   - Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
     tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)

   - Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
     the 'perf test' LLVM entries, when running it in-tree, to
     .gitignore (Yunlong Song)

   - libbpf error reporting improvements, using a strerror interface to
     more precisely tell the user about problems with the provided
     scriptlet, be it in C or as a ready made object file (Wang Nan)

   - Do not be case sensitive when searching for matching 'perf test'
     entries (Arnaldo Carvalho de Melo)

   - Inform the user about objdump failures in 'perf annotate' (Andi
     Kleen)

   - Improve the LLVM 'perf test' entry, introduce a new ones for BPF
     and kbuild tests to check the environment used by clang to compile
     .c scriptlets (Wang Nan)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
  tools include: Add compiler.h to list.h
  perf probe: Verify parameters in two functions
  perf session: Add missing newlines to some pr_err() calls
  perf annotate: Support full source file paths for srcline fix
  perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
  perf: Fix inherited events vs. tracepoint filters
  perf: Disable IRQs across RCU RS CS that acquires scheduler lock
  perf test: Do not be case sensitive when searching for matching tests
  perf test: Add 'perf test BPF'
  perf test: Enhance the LLVM tests: add kbuild test
  perf test: Enhance the LLVM test: update basic BPF test program
  perf bpf: Improve BPF related error messages
  perf tools: Make fetch_kernel_version() publicly available
  bpf tools: Add new API bpf_object__get_kversion()
  bpf tools: Improve libbpf error reporting
  perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
  perf annotate: Inform the user about objdump failures in --stdio
  perf stat: Make stat options global
  perf sched latency: Fix thread pid reuse issue
  ...

Pull scheduler fix from Thomas Gleixner:
 "A single fix to prevent math underflow in the numa balancing code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/numa: Fix math underflow in task_tick_numa()

Pull liblockdep fixes from Thomas Gleixner:
 "Three small patches to synchronize liblockdep with the latest core
  changes"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/liblockdep: explicitly declare lockdep API we call from liblockdep
  tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
  tools/liblockdep: remove task argument from debug_check_no_locks_held

Pull x86 fixes from Thomas Gleixner:
 "A couple of fixes and updates related to x86:

   - Fix the W+X check regression on XEN

   - The real fix for the low identity map trainwreck

   - Probe legacy PIC early instead of unconditionally allocating legacy
     irqs

   - Add cpu verification to long mode entry

   - Adjust the cache topology to AMD Fam17H systems

   - Let Merrifield use the TSC across S3"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Call verify_cpu() after having entered long mode too
  x86/setup: Fix low identity map for >= 2GB kernel range
  x86/mm: Skip the hypervisor range when walking PGD
  x86/AMD: Fix last level cache topology for AMD Fam17h systems
  x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
  x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield

Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq and timer fixes from Thomas Gleixner:

 - An irq regression fix to restore the wakeup behaviour of chained
   interrupts.

 - A timer fix for a long standing race versus timers scheduled on a
   target cpu which got exposed by recent changes in the workqueue
   implementation.

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/PM: Restore system wake up from chained interrupts

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers: Use proper base migration in add_timer_on()

Pull MIPS updates from Ralf Baechle:
 "These are the highlists of the main MIPS pull request for 4.4:

   - Add latencytop support
   - Support appended DTBs
   - VDSO support and initially use it for gettimeofday.
   - Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
   - Support for the 5KE, an internal test core.
   - Switch all MIPS platfroms to libata drivers.
   - Improved support, cleanups for ralink and Lantiq platforms.
   - Support for the new xilfpga platform.
   - A number of DTB improvments for BMIPS.
   - Improved support for CM and CPS.
   - Minor JZ4740 and BCM47xx enhancements"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
  MIPS: idle: add case for CPU_5KE
  MIPS: Octeon: Support APPENDED_DTB
  MIPS: vmlinux: create a section for appended DTB
  MIPS: Clean up compat_siginfo_t
  MIPS: Fix PAGE_MASK definition
  MIPS: BMIPS: Enable GZIP ramdisk and timed printks
  MIPS: Add xilfpga defconfig
  MIPS: xilfpga: Add mipsfpga platform code
  MIPS: xilfpga: Add xilfpga device tree files.
  dt-bindings: MIPS: Document xilfpga bindings and boot style
  MIPS: Make MIPS_CMDLINE_DTB default
  MIPS: Make the kernel arguments from dtb available
  MIPS: Use USE_OF as the guard for appended dtb
  MIPS: BCM63XX: Use pr_* instead of printk
  MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
  MIPS: lantiq: Disable xbar fpi burst mode
  MIPS: lantiq: Force the crossbar to big endian
  MIPS: lantiq: Initialize the USB core on boot
  MIPS: lantiq: Return correct value for fpi clock on ar9
  MIPS: ralink: Add missing clock on rt305x
  ...

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes tha have been gathered for
  4.4-rc1.  The only significant changes are those in PCI drivers
  Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
  A reverse select is often more user-friendly, but in this case, it
  makes hard to manage with the conflict with ZONE_DEVICE, so changed in
  such a way for now.

  Others are all small fixes and quirks: an error check in soundcore
  reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
  quirk, USB-audio DSD device quirk, some constifications, etc"

* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pci: depend on ZONE_DMA
  ALSA: hda - Simplify phantom jack handling for HDMI/DP
  ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
  ALSA: ctxfi: constify rsc ops structures
  ALSA: usb: Add native DSD support for Aune X1S
  ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
  sound: fix check for error condition of register_chrdev()

Pull ARC fixes from Vineet Gupta:
 "Found a couple of brown paper bag bugs with the prev pull request
  (including a SMP build breakage report from Guenter).  Since these are
  urgent I also decided to send over a bunch of other pending fixes
  which could have otherwise waited an rc or two.

  Summary:

   - A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
     failure)
   - cpu_relax() now compiler barrier for UP as well
   - handling of userspace Bus Errors for ARCompact builds"

* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Fix silly typo in MAINTAINERS file
  ARC: cpu_relax() to be compiler barrier even for UP
  ARC: use ASL assembler mnemonic
  ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
  ARC: remove extraneous header include
  ARCv2: lib: memcpy: use local symbols

cpu_relax() on ARC has been barrier only for SMP (and no-op for UP). Per
recent discussions, it is safer to make it a compiler barrier
unconditionally.

Link: http://lkml.kernel.org/r/53A7D3AA.9020100@synopsys.comAcked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

ARCompact and ARCv2 only have ASL, while binutils used to support LSL as
a alias mnemonic.

Newer binutils (upstream) don't want to do that so replace it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)

 - So move mem_service exception handler from common code into ARCv2 code.
 - In ARCompact code, define  mem_service as L2 interrupt handler which
   just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com>
Tested-by: Ana Martins <amartins@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Merge tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform

Pull chrome platform updates from Olof Johansson:
 "Here's the branch of chrome platform changes for v4.4.  Some have been
  queued up for the full 4.3 release cycle since I forgot to send them
  in for that round (rebased early on to deal with fixes conflicts).

  Most of these enable EC communication stuff -- Pixel 2015 support,
  enabling building for ARM64 platforms, and a few fixes for memory
  leaks.

  There's also a patch in here to allow reading/writing the verified
  boot context, which depends on a sysfs patch acked by Greg"

* tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  platform/chrome: Fix i2c-designware adapter name
  platform/chrome: Support reading/writing the vboot context
  sysfs: Support is_visible() on binary attributes
  platform/chrome: cros_ec: Fix possible leak in led_rgb_store()
  platform/chrome: cros_ec: Fix leak in sequence_store()
  platform/chrome: Enable Chrome platforms on 64-bit ARM
  platform/chrome: cros_ec_dev - Add a platform device ID table
  platform/chrome: cros_ec_lpc - Add support for Google Pixel 2
  platform/chrome: cros_ec_lpc - Use existing function to check EC result
  platform/chrome: Make depends on MFD_CROS_EC instead CROS_EC_PROTO
  Revert "platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM"

Merge tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull another x86 platform driver update from Darren Hart:
 "Support for the unfortunately rather unique ESC key on the Ideapad
  Yoga 3 and two DMI matches for rfkill support.  Solitary fix for
  potential missed errors for asus-wmi.  Downgrade a thinkpad_acpi
  message to info.

  asus-wmi:
   - fix error handling in store_sys_wmi()

  ideapad-laptop:
   - Add Lenovo Yoga 900 to no_hw_rfkill dmi list
   - include Yoga 3 1170 in add rfkill whitelist
   - add support for Yoga 3 ESC key

  thinkpad_acpi:
   - Don't yell on unsupported brightness interfaces"

* tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  asus-wmi: fix error handling in store_sys_wmi()
  ideapad-laptop: Add Lenovo Yoga 900 to no_hw_rfkill dmi list
  ideapad-laptop: include Yoga 3 1170 in add rfkill whitelist
  ideapad-laptop: add support for Yoga 3 ESC key
  thinkpad_acpi: Don't yell on unsupported brightness interfaces

Pull more input updates from Dmitry Torokhov:
 "An update to the tsc2005 driver that allows it to also support tsc2004
  (basically the same controller, but uses i2c instead of spi bus), and
  a couple of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: parkbd - drop bogus __init from parkbd_allocate_serio()
  Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
  Input: tsc2004 - add support for tsc2004
  Input: tsc200x-core - rename functions and variables
  Input: tsc2005 - separate SPI and core functions

Pull final round of SCSI updates from James Bottomley:
 "Sorry for the delay in this patch which was mostly caused by getting
  the merger of the mpt2/mpt3sas driver, which was seen as an essential
  item of maintenance work to do before the drivers diverge too much.
  Unfortunately, this caused a compile failure (detected by linux-next),
  which then had to be fixed up and incubated.

  In addition to the mpt2/3sas rework, there are updates from pm80xx,
  lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
  an assortment of changes including some year 2038 issues, a fix for a
  remove before detach issue in some drivers and a couple of other minor
  issues"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
  mpt3sas: fix inline markers on non inline function declarations
  sd: Clear PS bit before Mode Select.
  ibmvscsi: set max_lun to 32
  ibmvscsi: display default value for max_id, max_lun and max_channel.
  mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
  scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
  mvumi: 64bit value for seconds_since1970
  be2iscsi: Fix bogus WARN_ON length check
  scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
  mpt3sas: Bump mpt3sas driver version to 09.102.00.00
  mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
  mpt2sas, mpt3sas: Update the driver versions
  mpt3sas: setpci reset kernel oops fix
  mpt3sas: Added OEM Gen2 PnP ID branding names
  mpt3sas: Refcount fw_events and fix unsafe list usage
  mpt3sas: Refcount sas_device objects and fix unsafe list usage
  mpt3sas: sysfs attribute to report Backup Rail Monitor Status
  mpt3sas: Ported WarpDrive product SSS6200 support
  mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
  mpt3sas: Manage MSI-X vectors according to HBA device type
  ...