- 28 Nov, 2019 40 commits
-
-
Vandana BN authored
commit b4add02d upstream. When vbi stream is started, followed by video streaming, the vid_cap_streaming and vid_out_streaming were not being set to true, which would cause the video stream to stop when vbi stream is stopped. This patch allows to set vid_cap_streaming and vid_out_streaming to true. According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)' checks are a left-over from the original vivid development and should never have been there. Signed-off-by:
Vandana BN <bnvandana@gmail.com> Cc: <stable@vger.kernel.org> # for v3.18 and up Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guillaume Nault authored
commit 8f7dc9ae upstream. Using l2tp_tunnel_find() in l2tp_ip_recv() is wrong for two reasons: * It doesn't take a reference on the returned tunnel, which makes the call racy wrt. concurrent tunnel deletion. * The lookup is only based on the tunnel identifier, so it can return a tunnel that doesn't match the packet's addresses or protocol. For example, a packet sent to an L2TPv3 over IPv6 tunnel can be delivered to an L2TPv2 over UDPv4 tunnel. This is worse than a simple cross-talk: when delivering the packet to an L2TP over UDP tunnel, the corresponding socket is UDP, where ->sk_backlog_rcv() is NULL. Calling sk_receive_skb() will then crash the kernel by trying to execute this callback. And l2tp_tunnel_find() isn't even needed here. __l2tp_ip_bind_lookup() properly checks the socket binding and connection settings. It was used as a fallback mechanism for finding tunnels that didn't have their data path registered yet. But it's not limited to this case and can be used to replace l2tp_tunnel_find() in the general case. Fix l2tp_ip6 in the same way. Fixes: 0d76751f ("l2tp: Add L2TPv3 IP encapsulation (no UDP) support") Fixes: a32e0eec ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Nicolas Schier <n.schier@avm.de> Signed-off-by:
-
Oliver Neukum authored
commit 5f9f0b11 upstream. If starting the transfer of a command suceeds but the transfer for the reply fails, it is not enough to initiate killing the transfer for the command may still be running. You need to wait for the killing to finish before you can reuse URB and buffer. Reported-and-tested-by: syzbot+711468aa5c3a1eabf863@syzkaller.appspotmail.com Signed-off-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Waiman Long authored
commit cd5a2aa8 upstream. Since MDS and TAA mitigations are inter-related for processors that are affected by both vulnerabilities, the followiing confusing messages can be printed in the kernel log: MDS: Vulnerable MDS: Mitigation: Clear CPU buffers To avoid the first incorrect message, defer the printing of MDS mitigation after the TAA mitigation selection has been done. However, that has the side effect of printing TAA mitigation first before MDS mitigation. [ bp: Check box is affected/mitigations are disabled first before printing and massage. ] Suggested-by:
Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by:
Waiman Long <longman@redhat.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mark Gross <mgross@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Tyler Hicks <tyhicks@canonical.com> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20191115161445.30809-3-longman@redhat.comSigned-off-by:
-
Waiman Long authored
commit 64870ed1 upstream. For MDS vulnerable processors with TSX support, enabling either MDS or TAA mitigations will enable the use of VERW to flush internal processor buffers at the right code path. IOW, they are either both mitigated or both not. However, if the command line options are inconsistent, the vulnerabilites sysfs files may not report the mitigation status correctly. For example, with only the "mds=off" option: vulnerabilities/mds:Vulnerable; SMT vulnerable vulnerabilities/tsx_async_abort:Mitigation: Clear CPU buffers; SMT vulnerable The mds vulnerabilities file has wrong status in this case. Similarly, the taa vulnerability file will be wrong with mds mitigation on, but taa off. Change taa_select_mitigation() to sync up the two mitigation status and have them turned off if both "mds=off" and "tsx_async_abort=off" are present. Update documentation to emphasize the fact that both "mds=off" and "tsx_async_abort=off" have to be specified together for processors that are affected by both TAA and MDS to be effective. [ bp: Massage and add kernel-parameters.txt change too. ] Fixes: 1b42f017 ("x86/speculation/taa: Add mitigation for TSX Async Abort") Signed-off-by:
-
Alexander Kapshuk authored
commit 700c1018 upstream. gawk 5.0.1 generates the following regexp warnings: GEN /home/sasha/torvalds/tools/objtool/arch/x86/lib/inat-tables.c awk: ../arch/x86/tools/gen-insn-attr-x86.awk:260: warning: regexp escape sequence `\:' is not a known regexp operator awk: ../arch/x86/tools/gen-insn-attr-x86.awk:350: (FILENAME=../arch/x86/lib/x86-opcode-map.txt FNR=41) warning: regexp escape sequence `\&' is not a known regexp operator Ealier versions of gawk are not known to generate these warnings. The gawk manual referenced below does not list characters ':' and '&' as needing escaping, so 'unescape' them. See https://www.gnu.org/software/gawk/manual/html_node/Escape-Sequences.html for more info. Running diff on the output generated by the script before and after applying the patch reported no differences. [ bp: Massage commit message. ] [ Caught the respective tools header discrepancy. ] Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Alexander Kapshuk <alexander.kapshuk@gmail.com> Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190924044659.3785-1-alexander.kapshuk@gmail.comSigned-off-by:
-
Alexey Brodkin authored
commit 5effc09c upstream. 8-letter strings representing ARC perf events are stores in two 32-bit registers as ASCII characters like that: "IJMP", "IALL", "IJMPTAK" etc. And the same order of bytes in the word is used regardless CPU endianness. Which means in case of big-endian CPU core we need to swap bytes to get the same order as if it was on little-endian CPU. Otherwise we're seeing the following error message on boot: ------------------------->8---------------------- ARC perf : 8 counters (32 bits), 40 conditions, [overflow IRQ support] sysfs: cannot create duplicate filename '/devices/arc_pct/events/pmji' CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.18 #3 Stack Trace: arc_unwind_core+0xd4/0xfc dump_stack+0x64/0x80 sysfs_warn_dup+0x46/0x58 sysfs_add_file_mode_ns+0xb2/0x168 create_files+0x70/0x2a0 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at kernel/events/core.c:12144 perf_event_sysfs_init+0x70/0xa0 Failed to register pmu: arc_pct, reason -17 Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.18 #3 Stack Trace: arc_unwind_core+0xd4/0xfc dump_stack+0x64/0x80 __warn+0x9c/0xd4 warn_slowpath_fmt+0x22/0x2c perf_event_sysfs_init+0x70/0xa0 ---[ end trace a75fb9a9837bd1ec ]--- ------------------------->8---------------------- What happens here we're trying to register more than one raw perf event with the same name "PMJI". Why? Because ARC perf events are 4 to 8 letters and encoded into two 32-bit words. In this particular case we deal with 2 events: * "IJMP____" which counts all jump & branch instructions * "IJMPC___" which counts only conditional jumps & branches Those strings are split in two 32-bit words this way "IJMP" + "____" & "IJMP" + "C___" correspondingly. Now if we read them swapped due to CPU core being big-endian then we read "PMJI" + "____" & "PMJI" + "___C". And since we interpret read array of ASCII letters as a null-terminated string on big-endian CPU we end up with 2 events of the same name "PMJI". Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Cc: stable@vger.kernel.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Chester Lin authored
commit 1d31999c upstream. adjust_lowmem_bounds() checks every memblocks in order to find the boundary between lowmem and highmem. However some memblocks could be marked as NOMAP so they are not used by kernel, which should be skipped while calculating the boundary. Signed-off-by:
Chester Lin <clin@suse.com> Reviewed-by:
Mike Rapoport <rppt@linux.ibm.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Gang He authored
commit a6346447 upstream. Remove ocfs2_is_o2cb_active(). We have similar functions to identify which cluster stack is being used via osb->osb_cluster_stack. Secondly, the current implementation of ocfs2_is_o2cb_active() is not totally safe. Based on the design of stackglue, we need to get ocfs2_stack_lock before using ocfs2_stack related data structures, and that active_stack pointer can be NULL in the case of mount failure. Link: http://lkml.kernel.org/r/1495441079-11708-1-git-send-email-ghe@suse.comSigned-off-by:
Gang He <ghe@suse.com> Reviewed-by:
Joseph Qi <jiangqi903@gmail.com> Reviewed-by:
Eric Ren <zren@suse.com> Acked-by:
Changwei Ge <ge.changwei@h3c.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Bo Yan authored
commit 703cbaa6 upstream. cpufreq_resume can be called even without preceding cpufreq_suspend. This can happen in following scenario: suspend_devices_and_enter --> dpm_suspend_start --> dpm_prepare --> device_prepare : this function errors out --> dpm_suspend: this is skipped due to dpm_prepare failure this means cpufreq_suspend is skipped over --> goto Recover_platform, due to previous error --> goto Resume_devices --> dpm_resume_end --> dpm_resume --> cpufreq_resume In case schedutil is used as frequency governor, cpufreq_resume will eventually call sugov_start, which does following: memset(sg_cpu, 0, sizeof(*sg_cpu)); .... This effectively erases function pointer for frequency update, causing crash later on. The function pointer would have been set correctly if subsequent cpufreq_add_update_util_hook runs successfully, but that function returns earlier because cpufreq_suspend was not called: if (WARN_ON(per_cpu(cpufreq_update_util_data, cpu))) return; The fix is to check cpufreq_suspended first, if it's false, that means cpufreq_suspend was not called in the first place, so do not resume cpufreq. Signed-off-by:
Bo Yan <byan@nvidia.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> [ rjw: Dropped printing a message ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Hari Vyas authored
commit e4ba15de upstream. The bad_mode() handler is called if we encounter an uunknown exception, with the expectation that the subsequent call to panic() will halt the system. Unfortunately, if the exception calling bad_mode() is taken from EL0, then the call to die() can end up killing the current user task and calling schedule() instead of falling through to panic(). Remove the die() call altogether, since we really want to bring down the machine in this "impossible" case. Signed-off-by:
Hari Vyas <hari.vyas@broadcom.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Bart Van Assche authored
commit 2e91c369 upstream. After QUEUE_FLAG_DYING has been set any code that is waiting in get_request() should be woken up. But to get this behaviour blk_set_queue_dying() must be used instead of only setting QUEUE_FLAG_DYING. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Denis Efremov authored
commit 80e84f36 upstream. Currently, data variable in ar9003_hw_thermo_cal_apply() could be uninitialized if ar9300_otp_read_word() will fail to read the value. Initialize data variable with 0 to prevent an undefined behavior. This will be enough to handle error case when ar9300_otp_read_word() fails. Fixes: 80fe43f2 ("ath9k_hw: Read and configure thermocal for AR9462") Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: stable@vger.kernel.org Signed-off-by:
Denis Efremov <efremov@linux.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Sean Christopherson authored
commit a78986aa upstream. Explicitly exempt ZONE_DEVICE pages from kvm_is_reserved_pfn() and instead manually handle ZONE_DEVICE on a case-by-case basis. For things like page refcounts, KVM needs to treat ZONE_DEVICE pages like normal pages, e.g. put pages grabbed via gup(). But for flows such as setting A/D bits or shifting refcounts for transparent huge pages, KVM needs to to avoid processing ZONE_DEVICE pages as the flows in question lack the underlying machinery for proper handling of ZONE_DEVICE pages. This fixes a hang reported by Adam Borowski[*] in dev_pagemap_cleanup() when running a KVM guest backed with /dev/dax memory, as KVM straight up doesn't put any references to ZONE_DEVICE pages acquired by gup(). Note, Dan Williams proposed an alternative solution of doing put_page() on ZONE_DEVICE pages immediately after gup() in order to simplify the auditing needed to ensure is_zone_device_page() is called if and only if the backing device is pinned (via gup()). But that approach would break kvm_vcpu_{un}map() as KVM requires the page to be pinned from map() 'til unmap() when accessing guest memory, unlike KVM's secondary MMU, which coordinates with mmu_notifier invalidations to avoid creating stale page references, i.e. doesn't rely on pages being pinned. [*] http://lkml.kernel.org/r/20190919115547.GA17963@angband.plReported-by:
Adam Borowski <kilobyte@angband.pl> Analyzed-by:
David Hildenbrand <david@redhat.com> Acked-by:
Dan Williams <dan.j.williams@intel.com> Cc: stable@vger.kernel.org Fixes: 3565fce3 ("mm, x86: get_user_pages() for dax mappings") Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Tomas Bortoli authored
commit cf94da6f upstream. Syzbot reported an invalid-free that I introduced fixing a memleak. bcsp_recv() also frees bcsp->rx_skb but never nullifies its value. Nullify bcsp->rx_skb every time it is freed. Signed-off-by:
Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+a0d209a4676664613e76@syzkaller.appspotmail.com Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: Alexander Potapenko <glider@google.com> Signed-off-by:
-
zhong jiang authored
[ Upstream commit d2ab9940 ] When adding the memory by probing memory block in sysfs interface, there is an obvious issue that we will unlock the device_hotplug_lock when fails to takes it. That issue was introduced in Commit 8df1d0e4 ("mm/memory_hotplug: make add_memory() take the device_hotplug_lock") We should drop out in time when fails to take the device_hotplug_lock. Fixes: 8df1d0e4 ("mm/memory_hotplug: make add_memory() take the device_hotplug_lock") Reported-by:
Yang yingliang <yangyingliang@huawei.com> Signed-off-by:
zhong jiang <zhongjiang@huawei.com> Reviewed-by:
Oscar Salvador <osalvador@suse.de> Reviewed-by:
Michal Hocko <mhocko@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Vignesh R authored
[ Upstream commit baf8b9f8 ] Commit b682cffa ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length") broke SPI transfers where bits_per_word != 8. This is because of mimsatch between McSPI FIFO level event trigger size (SPI word length) and DMA request size(word length * maxburst). This leads to data corruption, lockup and errors like: spi1.0: EOW timed out Fix this by setting DMA maxburst size to 1 so that McSPI FIFO level event trigger size matches DMA request size. Fixes: b682cffa ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length") Cc: stable@vger.kernel.org Reported-by:
David Lechner <david@lechnology.com> Tested-by:
Vignesh R <vigneshr@ti.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Kishon Vijay Abraham I authored
[ Upstream commit 148e340c ] PCI controller in K2G also has a limitation that memory read request size (MRRS) must not exceed 256 bytes. Use the quirk to limit MRRS (added for K2HK, K2L and K2E) for K2G as well. Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit cd8a145a ] Clang warns when one enumerated type is implicitly converted to another: drivers/pinctrl/pinctrl-zynq.c:985:18: warning: implicit conversion from enumeration type 'enum zynq_pin_config_param' to different enumeration type 'enum pin_config_param' [-Wenum-conversion] {"io-standard", PIN_CONFIG_IOSTANDARD, zynq_iostd_lvcmos18}, ~ ^~~~~~~~~~~~~~~~~~~~~ drivers/pinctrl/pinctrl-zynq.c:990:16: warning: implicit conversion from enumeration type 'enum zynq_pin_config_param' to different enumeration type 'enum pin_config_param' [-Wenum-conversion] = { PCONFDUMP(PIN_CONFIG_IOSTANDARD, "IO-standard", NULL, true), ~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from macro 'PCONFDUMP' .param = a, .display = b, .format = c, .has_arg = d \ ^ 2 warnings generated. It is expected that pinctrl drivers can extend pin_config_param because of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion isn't an issue. Most drivers that take advantage of this define the PIN_CONFIG variables as constants, rather than enumerated values. Do the same thing here so that Clang no longer warns. Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Acked-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit f24bfb39 ] Clang warns when one enumerated type is implicitly converted to another: drivers/pinctrl/pinctrl-lpc18xx.c:643:29: warning: implicit conversion from enumeration type 'enum lpc18xx_pin_config_param' to different enumeration type 'enum pin_config_param' [-Wenum-conversion] {"nxp,gpio-pin-interrupt", PIN_CONFIG_GPIO_PIN_INT, 0}, ~ ^~~~~~~~~~~~~~~~~~~~~~~ drivers/pinctrl/pinctrl-lpc18xx.c:648:12: warning: implicit conversion from enumeration type 'enum lpc18xx_pin_config_param' to different enumeration type 'enum pin_config_param' [-Wenum-conversion] PCONFDUMP(PIN_CONFIG_GPIO_PIN_INT, "gpio pin int", NULL, true), ~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from macro 'PCONFDUMP' .param = a, .display = b, .format = c, .has_arg = d \ ^ 2 warnings generated. It is expected that pinctrl drivers can extend pin_config_param because of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion isn't an issue. Most drivers that take advantage of this define the PIN_CONFIG variables as constants, rather than enumerated values. Do the same thing here so that Clang no longer warns. Link: https://github.com/ClangBuiltLinux/linux/issues/140Signed-off-by:
-
Brian Masney authored
[ Upstream commit 149a9604 ] When attempting to setup up a gpio hog, device probing would repeatedly fail with -EPROBE_DEFERED errors. It was caused by a circular dependency between the gpio and pinctrl frameworks. If the gpio-ranges property is present in device tree, then the gpio framework will handle the gpio pin registration and eliminate the circular dependency. See Christian Lamparter's commit a86caa9b ("pinctrl: msm: fix gpio-hog related boot issues") for a detailed commit message that explains the issue in much more detail. The code comment in this commit came from Christian's commit. Signed-off-by:
Brian Masney <masneyb@onstation.org> Signed-off-by:
-
David Barmann authored
[ Upstream commit 50254256 ] When setting the SO_MARK socket option, if the mark changes, the dst needs to be reset so that a new route lookup is performed. This fixes the case where an application wants to change routing by setting a new sk_mark. If this is done after some packets have already been sent, the dst is cached and has no effect. Signed-off-by:
David Barmann <david.barmann@stackpath.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 0db55093 ] Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/broadcom/genet/bcmgenet.c: In function 'bcmgenet_power_down': drivers/net/ethernet/broadcom/genet/bcmgenet.c:1136:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable] bcmgenet_power_down should return 'ret' instead of 0. Fixes: ca8cf341 ("net: bcmgenet: propagate errors from bcmgenet_power_down") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit f8ddf49b ] Fix warnings found using static analysis with cppcheck, use %d printf format specifier for signed ints rather than %u Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Erik Schmauss <erik.schmauss@intel.com> Signed-off-by:
-
Tycho Andersen authored
[ Upstream commit 9de30f3f ] In copy_result_to_user(), we first create a struct dlm_lock_result, which contains a struct dlm_lksb, the last member of which is a pointer to the lvb. Unfortunately, we copy the entire struct dlm_lksb to the result struct, which is then copied to userspace at the end of the function, leaking the contents of sb_lvbptr, which is a valid kernel pointer in some cases (indeed, later in the same function the data it points to is copied to userspace). It is an error to leak kernel pointers to userspace, as it undermines KASLR protections (see e.g. 65eea8ed ("floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl") for another example of this). Signed-off-by:
Tycho Andersen <tycho@tycho.ws> Signed-off-by:
David Teigland <teigland@redhat.com> Signed-off-by:
-
Tycho Andersen authored
[ Upstream commit d968b4e2 ] dlm_config_nodes() does not allocate nodes on failure, so we should not free() nodes when it fails. Signed-off-by:
-
James Smart authored
[ Upstream commit 036cad1f ] On FCoE adapters, when running link bounce test in a loop, initiator failed to login with switch switch and required driver reload to recover. Switch reached a point where all subsequent FLOGIs would be LS_RJT'd. Further testing showed the condition to be related to not performing FCF discovery between FLOGI's. Fix by monitoring FLOGI failures and once a repeated error is seen repeat FCF discovery. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Shivasharan S authored
[ Upstream commit 9155cf30 ] In megasas_transition_to_ready() driver waits 180seconds for controller to change FW state. Here we are calling msleep(1) in a loop for this. As explained in timers-howto.txt, msleep(1) will actually sleep longer than 1ms. If a faulty controller is connected, we will end up waiting for much more than 180 seconds causing unnecessary delays during load. Change the granularity of msleep() call from 1ms to 1000ms. Signed-off-by:
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by:
-
Suganath Prabu authored
[ Upstream commit 97f35194 ] Currently driver is modifying both current & NVRAM/persistent data in Manufacturing page11. Driver should change only current copy of Manufacturing page11. It should not modify the persistent data. So removed the section of code where driver is modifying the persistent data of Manufacturing page11. Signed-off-by:
Suganath Prabu <suganath-prabu.subramani@broadcom.com> Reviewed-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
Suganath Prabu authored
[ Upstream commit 9029a725 ] This is to fix SYNC CACHE and START STOP command failures with DID_NO_CONNECT during driver unload. In driver's IO submission patch (i.e. in driver's .queuecommand()) driver won't allow any SCSI commands to the IOC when ioc->remove_host flag is set and hence SYNC CACHE commands which are issued to the target drives (where write cache is enabled) during driver unload time is failed with DID_NO_CONNECT status. Now modified the driver to allow SYNC CACHE and START STOP commands to IOC, even when remove_host flag is set. Signed-off-by:
-
Shaokun Zhang authored
[ Upstream commit 7d129adf ] RT_TRACE shows REG_MCUFWDL value as a decimal value with a '0x' prefix, which is somewhat misleading. Fix it to print hexadecimal, as was intended. Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Shaokun Zhang <zhangshaokun@hisilicon.com> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 3d39e1bb ] It looks like we wanted to print a maximum of BSSList_rid.ssidLen bytes of the ssid, but we accidentally use "%*s" (width) instead of "%.*s" (precision) so if the ssid doesn't have a NUL terminator this could lead to an overflow. Static analysis. Not tested. Fixes: e174961c ("net: convert print_mac to %pM") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Ali MJ Al-Nasrawy authored
[ Upstream commit 96fca788 ] This message greatly spams the log under heavy Tx of frames with BK access class which is especially true when operating as AP. It is also not informative as the "agg'ablity" of TIDs are set once and never change. Fix this by logging only in debug mode. Signed-off-by:
Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com> Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit 307b00c5 ] Add missing break statement in order to prevent the code from falling through to the default case. Fixes: 26f1fad2 ("New driver: rtl8xxxu (mac80211)") Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 3419348a ] We return 0 unconditionally at the end of 'wlcore_vendor_cmd_smart_config_start()'. However, 'ret' is set to some error codes in several error handling paths and we already return some error codes at the beginning of the function. Return 'ret' instead to propagate the error code. Fixes: 80ff8063 ("wlcore: handle smart config vendor commands") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Richard Guy Briggs authored
[ Upstream commit ea956d8b ] Empty executable arguments were being skipped when printing out the list of arguments in an EXECVE record, making it appear they were somehow lost. Include empty arguments as an itemized empty string. Reproducer: autrace /bin/ls "" "/etc" ausearch --start recent -m execve -i | grep EXECVE type=EXECVE msg=audit(10/03/2018 13:04:03.208:1391) : argc=3 a0=/bin/ls a2=/etc With fix: type=EXECVE msg=audit(10/03/2018 21:51:38.290:194) : argc=3 a0=/bin/ls a1= a2=/etc type=EXECVE msg=audit(1538617898.290:194): argc=3 a0="/bin/ls" a1="" a2="/etc" Passes audit-testsuite. GH issue tracker at https://github.com/linux-audit/audit-kernel/issues/99Signed-off-by:
Richard Guy Briggs <rgb@redhat.com> [PM: cleaned up the commit metadata] Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Valentin Schneider authored
[ Upstream commit 3f130a37 ] When load_balance() fails to move some load because of task affinity, we end up increasing sd->balance_interval to delay the next periodic balance in the hopes that next time we look, that annoying pinned task(s) will be gone. However, idle_balance() pays no attention to sd->balance_interval, yet it will still lead to an increase in balance_interval in case of pinned tasks. If we're going through several newidle balances (e.g. we have a periodic task), this can lead to a huge increase of the balance_interval in a very small amount of time. To prevent that, don't increase the balance interval when going through a newidle balance. This is a similar approach to what is done in commit 58b26c4c ("sched: Increment cache_nice_tries only on periodic lb"), where we disregard newidle balance and rely on periodic balance for more stable results. Signed-off-by:
Valentin Schneider <valentin.schneider@arm.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Dietmar.Eggemann@arm.com Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: patrick.bellasi@arm.com Cc: vincent.guittot@linaro.org Link: http://lkml.kernel.org/r/1537974727-30788-2-git-send-email-valentin.schneider@arm.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit fe60faa5 ] Before calling dev_hard_start_xmit(), upper layers tried to cook optimal skb list based on BQL budget. Problem is that GSO packets can end up comsuming more than the BQL budget. Breaking the loop is not useful, since requeued packets are ahead of any packets still in the qdisc. It is also more expensive, since next TX completion will push these packets later, while skbs are not in cpu caches. It is also a behavior difference with TSO packets, that can break the BQL limit by a large amount. Note that drivers should use __netdev_tx_sent_queue() in order to have optimal xmit_more support, and avoid useless atomic operations as shown in the following patch. Signed-off-by:
-
Larry Chen authored
[ Upstream commit 6194ae42 ] ocfs2_defrag_extent() might leak allocated clusters. When the file system has insufficient space, the number of claimed clusters might be less than the caller wants. If that happens, the original code might directly commit the transaction without returning clusters. This patch is based on code in ocfs2_add_clusters_in_btree(). [akpm@linux-foundation.org: include localalloc.h, reduce scope of data_ac] Link: http://lkml.kernel.org/r/20180904041621.16874-3-lchen@suse.comSigned-off-by:
Larry Chen <lchen@suse.com> Reviewed-by:
-
Changwei Ge authored
[ Upstream commit cf76c785 ] ocfs2_read_blocks() and ocfs2_read_blocks_sync() are both used to read several blocks from disk. Currently, the input argument *bhs* can be NULL or NOT. It depends on the caller's behavior. If the function fails in reading blocks from disk, the corresponding bh will be assigned to NULL and put. Obviously, above process for non-NULL input bh is not appropriate. Because the caller doesn't even know its bhs are put and re-assigned. If buffer head is managed by caller, ocfs2_read_blocks and ocfs2_read_blocks_sync() should not evaluate it to NULL. It will cause caller accessing illegal memory, thus crash. Link: http://lkml.kernel.org/r/HK2PR06MB045285E0F4FBB561F9F2F9B3D5680@HK2PR06MB0452.apcprd06.prod.outlook.comSigned-off-by:
Guozhonghua <guozhonghua@h3c.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by:
-
