This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.

This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.

The device operates in two different modes and the difference
in these two modes in primarily in the TX side.

(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.

RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.

(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.

RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.

The devices can be added using the "ip" command from the iproute2
package -

	ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Ben Hutchings drivers that allow using VLAN have to
provide enough headroom for the VLAN tags.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

i.MX6SX fec support three rx ring1, the current driver lost to init
ring1 and ring2 maximum receive buffer size, that cause receving
frame date length error. The driver reports "rcv is not +last" error
log in user case.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key might increase attack surface.

Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change has no functional impact and simply addresses some coding
style issues detected by checkpatch. Specifically this change
adjusts "if" statements which also include the assignment of a
variable.

No changes to the resultant object files result as determined by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the access to wq has been moved out of hardirq context. We no longer need to
use spin_lock_irqsave.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic_isr_legacy(), enic_isr_msix() & enic_isr_msi() run from hard
interrupt context.

They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_set_rxfh() can crash if no RSS indir table is provided.

While we are at it, allow RSS key to be changed with ethtool -X

Tested:

myhost:~# cat /proc/sys/net/core/netdev_rss_key
b6:89:91:f3:b2:c3:c2:90:11:e8:ce:45:e8:a9:9d:1c:f2:f6:d4:53:61:8b:26:3a:b3:9a:57:97:c3:b6:79:4d:2e:d9:66:5c:72:ed:b6:8e:c5:5d:4d:8c:22:67:30:ab:8a:6e:c3:6a

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
b6:89:91:f3:b2:c3:c2:90:11:e8:ce:45:e8:a9:9d:1c:f2:f6:d4:53:61:8b:26:3a:b3:9a:57:97:c3:b6:79:4d:2e:d9:66:5c:72:ed:b6:8e

myhost:~# ethtool -X eth0 hkey \
03:0e:e2:43:fa:82:0e:73:14:2d:c0:68:21:9e:82:99:b9:84:d0:22:e2:b3:64:9f:4a:af:00:fa:cc:05:b4:4a:17:05:14:73:76:58:bd:2f

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
03:0e:e2:43:fa:82:0e:73:14:2d:c0:68:21:9e:82:99:b9:84:d0:22:e2:b3:64:9f:4a:af:00:fa:cc:05:b4:4a:17:05:14:73:76:58:bd:2f
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: b9d1ab7e ("mlx4: use netdev_rss_key_fill() helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
RDMA/cxgb4,cxgb4vf,csiostor: Cleanup macros

This series continues to cleanup all the macros/register defines related to
filter, port, VI, queue, RSS, LDST, firmware, etc that are defined in t4fw_api.h
and the affected files.

Will post few more series so that we can cover all the macros so that they all
follow the same style to be consistent.

The patches series is created against 'net-next' tree.
And includes patches on cxgb4, cxgb4vf, iw_cxgb4 and csiostor driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all PCIE, RSS & FW related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all port and VI related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all queue related macros/register defines that are defined
in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups PF/VF and LDST related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all filter related macros/register defines that are defined
in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original FDB code submission wasn't correct and the code
wasn't enabled.  This removes some dead code (can use the common kernel
code for fdb_del and fdb_dump) and correctly enables the fdb_add
function pointer.

The fdb_add functionality is important to i40e because it is needed
for a workaround to allow bridges to work correctly on the i40e
hardware.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ieee802154/fakehard.c

A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.

Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.

 2) nf_nat_range is not fully initialized and this is copied back to
    userspace, from Daniel Borkmann.

 3) Fix read past end of b uffer in netfilter ipset, also from Dan
    Carpenter.

 4) Signed integer overflow in ipv4 address mask creation helper
    inet_make_mask(), from Vincent BENAYOUN.

 5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
    properly describe the device's capabilities, from Joe Stringer.

 6) Fix memory leaks and checksum miscalculations in openvswitch, from
    Pravin B SHelar and Jesse Gross.

 7) FIB rules passes back ambiguous error code for unreachable routes,
    making behavior confusing for userspace.  Fix from Panu Matilainen.

 8) ieee802154fake_probe() doesn't release resources properly on error,
    from Alexey Khoroshilov.

 9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.

10) Fix access of stale slave pointers in bonding code, from Nikolay
    Aleksandrov.

11) Fix stack info leak in PPP pptp code, from Mathias Krause.

12) Cure locking bug in IPX stack, from Jiri Bohac.

13) Revert SKB fclone memory freeing optimization that is racey and can
    allow accesses to freed up memory, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
  tcp: Restore RFC5961-compliant behavior for SYN packets
  net: Revert "net: avoid one atomic operation in skb_clone()"
  virtio-net: validate features during probe
  cxgb4 : Fix DCB priority groups being returned in wrong order
  ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
  openvswitch: Don't validate IPv6 label masks.
  pptp: fix stack info leak in pptp_getname()
  brcmfmac: don't include linux/unaligned/access_ok.h
  cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
  ipv6: delete protocol and unregister rtnetlink when cleanup
  net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
  bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
  mac80211: minstrel_ht: fix a crash in rate sorting
  vxlan: Inline vxlan_gso_check().
  can: m_can: update to support CAN FD features
  can: m_can: fix incorrect error messages
  can: m_can: add missing delay after setting CCCR_INIT bit
  can: m_can: fix not set can_dlc for remote frame
  can: m_can: fix possible sleep in napi poll
  can: m_can: add missing message RAM initialization
  ...

Pull drm fixes from Dave Airlie:
 "Just two radeon and two intel fixes: endian and regression fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: fix endian swapping in vbios fetch for tdp table
  drm/radeon: disable native backlight control on pre-r6xx asics (v2)
  drm/i915: Kick fbdev before vgacon
  drm/i915: drop WaSetupGtModeTdRowDispatch:snb

Pull sound fixes from Takashi Iwai:
 "This batch ended up as a relatively high volume due to pending ASoC
  fixes.  But most of fixes there are trivial and/or device- specific
  fixes and quirks, so safe to apply.  The only (ASoC) core fixes are
  the DPCM race fix and the machine-driver matching fix for
  componentization"

* tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - fix the mic mute led problem for Latitude E5550
  ALSA: hda - move DELL_WMI_MIC_MUTE_LED to the tail in the quirk chain
  ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
  ALSA: usb-audio: Set the Control Selector to SU_SELECTOR_CONTROL for UAC2
  ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
  ASoC: sgtl5000: Fix SMALL_POP bit definition
  ASoC: cs42l51: re-hook of_match_table pointer
  ASoC: rt5670: change dapm routes of PLL connection
  ASoC: rt5670: correct the incorrect default values
  ASoC: samsung: Add MODULE_DEVICE_TABLE for Snow
  ASoC: max98090: Correct pclk divisor settings
  ASoC: dpcm: Fix race between FE/BE updates and trigger
  ASoC: Fix snd_soc_find_dai() matching component by name
  ASoC: rsnd: remove unsupported PAUSE flag
  ASoC: fsi: remove unsupported PAUSE flag
  ASoC: rt5645: Mark RT5645_TDM_CTRL_3 as readable
  ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_rxctrl
  ASoC: es8328-i2c: Fix i2c_device_id name field in es8328_id
  ASoC: fsl_asrc: Add reg_defaults for regmap to fix kernel dump

Pull ACPI power management fix from Rafael Wysocki:
 "This is just a one-liner fixing a regression introduced in 3.13 that
  broke system suspend on some Chromebooks.

  On those machines there are ACPI device objects for some I2C devices
  that can wake up the system from sleep states, but that is done via a
  platform-specific mechanism and the ACPI objects don't contain any
  wakeup-related information.  When we started to use ACPI power
  management with those devices (which happened during the 3.13 cycle),
  their configuration confused the ACPI PM layer that returned error
  codes from suspend callbacks for them causing system suspend to fail.

  However, the ACPI PM layer can safely ignore the wakeup setting from a
  device driver if the ACPI object corresponding to the device in
  question doesn't contain wakeup information in which case the driver
  itself is responsible for setting up the device for system wakeup"

* tag 'pm+acpi-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Ignore wakeup setting if the ACPI companion can't wake up

Pull devicetree fixes from Rob Herring:
 "DeviceTree fixes for 3.18:

   - two fixes for OF selftest code
   - fix for PowerPC address parsing to disable work-around except on
     old PowerMACs
   - fix a crash when earlycon is enabled, but no device is found
   - DT documentation fixes and missing vendor prefixes

  All but the doc updates are also for stable"

* tag 'devicetree-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of/selftest: Fix testing when /aliases is missing
  of/selftest: Fix off-by-one error in removal path
  documentation: pinctrl bindings: Fix trivial typo 'abitrary'
  devicetree: bindings: Add vendor prefix for Micron Technology, Inc.
  of: Add vendor prefix for Chips&Media, Inc.
  of/base: Fix PowerPC address parsing hack
  devicetree: vendor-prefixes.txt: fix whitespace
  of: Fix crash if an earlycon driver is not found
  of/irq: Drop obsolete 'interrupts' vs 'interrupts-extended' text
  of: Spelling s/stucture/structure/
  devicetree: bindings: add sandisk to the vendor prefixes

Pull PCI fixes from Bjorn Helgaas:
 "These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
  PAE kernels, an APM X-Gene problem (it depended on a generic change we
  removed before merging), a fix for my hotplug device configuration
  changes, and a devicetree documentation update.

  Resource management:
    - Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)

  PCI device hotplug:
    - Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)

  Generic host bridge driver:
    - Add DT binding for "linux,pci-domain" property (Lucas Stach)

  APM X-Gene:
    - Assign resources to bus before adding new devices (Duc Dang)"

* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
  PCI: Apply _HPX Link Control settings to all devices with a link
  PCI: Add missing DT binding for "linux,pci-domain" property
  PCI: xgene: Assign resources to bus before adding new devices

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the target-pending fixes queued for v3.18-rc6.

  The highlights include:

   - target-core OOPs fix with tcm_qla2xxx + vxworks FC initiators +
     zero length SCSI commands having a transfer direction set.  (Roland
     + Craig Watson)

   - vhost-scsi OOPs fix to explicitly prevent WWPN endpoint configfs
     group removal while qemu still has an active reference.  (Paolo +
     nab)

   - ib_srpt fix for RDMA hardware with lower srp_sq_size limits.
     (Bart)

   - two ib_isert work-arounds for running on ocrdma hardware (Or + Sagi
     + Chris)

   - iscsi-target discovery portal typo + SPC-3 PR Preempt SA key
     matching fix (Steve)"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  IB/isert: Adjust CQ size to HW limits
  target: return CONFLICT only when SA key unmatched
  iser-target: Handle DEVICE_REMOVAL event on network portal listener correctly
  ib_isert: Add max_send_sge=2 minimum for control PDU responses
  srp-target: Retry when QP creation fails with ENOMEM
  iscsi-target: return the correct port in SendTargets
  vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
  target: Don't call TFO->write_pending if data_length == 0

Pull dmaengine fixes from Vinod Koul:
 "We have couple of fixes for dmaengine queued up:
   - dma mempcy fix for dma configuration of sun6i by Maxime
   - pl330 fixes: First the fixing allocation for data buffers by Liviu
     and then Jon's fixe for fifo width and usage"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: Fix allocation size for PL330 data buffer depth.
  dmaengine: pl330: Limit MFIFO usage for memcpy to avoid exhausting entries
  dmaengine: pl330: Align DMA memcpy operations to MFIFO width
  dmaengine: sun6i: Fix memcpy operation

Pull MIPS fixes from Ralf Baechle:
 "More 3.18 fixes for MIPS:

   - backtraces were not quite working on on 64-bit kernels
   - loongson needs a different cache coherency setting
   - Loongson 3 is a MIPS64 R2 version but due to erratum we treat is an
     older architecture revision.
   - fix build errors due to undefined references to __node_distances
     for certain configurations.
   - fix instruction decodig in the jump label code.
   - for certain configurations copy_{from,to}_user destroy the content
     of $3 so that register needs to be marked as clobbed by the calling
     code.
   - Hardware Table Walker fixes.
   - fill the delay slot of the last instruction of memcpy otherwise
     whatever ends up there randomly might have undesirable effects.
   - ensure get_user/__get_user always zero the variable to be read even
     in case of an error"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: jump_label.c: Handle the microMIPS J instruction encoding
  MIPS: jump_label.c: Correct the span of the J instruction
  MIPS: Zero variable read by get_user / __get_user in case of an error.
  MIPS: lib: memcpy: Restore NOP on delay slot before returning to caller
  MIPS: tlb-r4k: Add missing HTW stop/start sequences
  MIPS: asm: uaccess: Add v1 register to clobber list on EVA
  MIPS: oprofile: Fix backtrace on 64-bit kernel
  MIPS: Loongson: Set Loongson-3's ISA level to MIPS64R1
  MIPS: Loongson: Fix the write-combine CCA value setting
  MIPS: IP27: Fix __node_distances undefined error
  MIPS: Loongson3: Fix __node_distances undefined error

Pull powerpc fix from Michael Ellerman:
 "One fix from Scott, he says:

  This patch fixes a crash (introduced in v3.18-rc1) in the FSL MSI driver
  when threaded IRQs are enabled"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/fsl_msi: mark the msi cascade handler IRQF_NO_THREAD

Pull x86 fixes from Thomas Gleixner:
 "Misc fixes:
   - gold linker build fix
   - noxsave command line parsing fix
   - bugfix for NX setup
   - microcode resume path bug fix
   - _TIF_NOHZ versus TIF_NOHZ bugfix as discussed in the mysterious
     lockup thread"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, syscall: Fix _TIF_NOHZ handling in syscall_trace_enter_phase1
  x86, kaslr: Handle Gold linker for finding bss/brk
  x86, mm: Set NX across entire PMD at boot
  x86, microcode: Update BSPs microcode on resume
  x86: Require exact match for 'noxsave' command line option

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: two NUMA fixes, two cputime fixes and an RCU/lockdep fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency
  sched/cputime: Fix cpu_timer_sample_group() double accounting
  sched/numa: Avoid selecting oneself as swap target
  sched/numa: Fix out of bounds read in sched_init_numa()
  sched: Remove lockdep check in sched_move_task()

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two Intel uncore driver fixes, a CPU-hotplug fix and a
  build dependencies fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/uncore: Fix boot crash on SBOX PMU on Haswell-EP
  perf/x86/intel/uncore: Fix IRP uncore register offsets on Haswell EP
  perf: Fix corruption of sibling list with hotplug
  perf/x86: Fix embarrasing typo

Pull core fix from Ingo Molnar:
 "Fix GENMASK macro shift overflow"

Nobody seems to currently use GENMASK() to fill every single last bit
(which is what overflows) in-tree, and gcc would warn about it, so we
have that going for us.  But apparently there are pending changes that
want this.

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  bitops: Fix shift overflow in GENMASK macros

Merge tag 'master-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
pull request: wireless-next 2014-11-21

Please pull this batch of updates intended for the 3.19 stream...

For the mac80211 bits, Johannes says:

"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
 * TDLS off-channel support set from Arik/Liad, with some support
   patches I did
 * custom regulatory fixes from Arik
 * minstrel VHT fix (and a small optimisation) from Felix
 * add back radiotap vendor namespace support (myself)
 * random MAC address scanning for cfg80211/mac80211/hwsim (myself)
 * CSA improvements (Luca)
 * WoWLAN Net Detect (wake on network found) support (Luca)
 * and lots of other smaller changes from many people"

For the Bluetooth bits, Johan says:

"Here's another set of patches for 3.19. Most of it is again fixes and
cleanups to ieee802154 related code from Alexander Aring. We've also got
better handling of hardware error events along with a proper API for HCI
drivers to notify the HCI core of such situations. There's also a minor
fix for mgmt events as well as a sparse warning fix. The code for
sending HCI commands synchronously also gets a fix where we might loose
the completion event in the case of very fast HW (particularly easily
reproducible with an emulated HCI device)."

And...

"Here's another bluetooth-next pull request for 3.19. We've got:

 - Various fixes, cleanups and improvements to ieee802154/mac802154
 - Support for a Broadcom BCM20702A1 variant
 - Lots of lockdep fixes
 - Fixed handling of LE CoC errors that should trigger SMP"

For the Atheros bits, Kalle says:

"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:

o fix resume (Bartosz)

o firmware restart is now faster and more reliable (Michal)

o it's now possible to test hardware restart functionality without
  crashing the firmware using hw-restart parameter with
  simulate_fw_crash debugfs file (Michal)"

On top of that...both ath9k and mwifiex get their usual level of
updates.  Of note is the ath9k spectral scan work from Oleksij Rempel.

I also pulled from the wireless tree in order to avoid some merge issues.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Maciej W. Rozycki says:

====================
defxx: Assorted fixes, mainly for EISA

 This is another small series fixing issues with the defxx driver,
mainly for EISA boards, but there's one patch for PCI as well.

 In the end, with the inexistent second IDE channel forcefully disabled
in the IDE driver, I wasn't able to retrigger spurious IRQ 15 interrupts
I previously saw and suspected the DEFEA to be the cause.  So it looks
to me these were real noise on IRQ 15 rather than the latency in
interrupt acknowledge in the DEFEA board causing the slave 8259A to
issue the spurious interrupt vector.  In any case not an issue with the
defxx driver, so nothing to do here unless the problem resurfaces.

 I haven't seen your announcement about opening net-next since the
closure on Oct 6th, but from the patch traffic and the policy described
in Documentation/networking/netdev-FAQ.txt I gather your tree is open.
And these are bug fixes anyway, not new features, so please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reserve DEFEA resources according to actual use.  There are three
regions, for the ESIC ASIC's CSRs, for the discrete Burst Holdoff
register, and for the PDQ ASIC's CSRs.  The latter is mapped in the
memory or port I/O address space depending on configuration.  The two
formers are hardwired and always mapped in the port I/O address space.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the option card does not respond after shutdown by disabling
it via ESIC's Expansion Board Control register.  Also disable memory and
port I/O decoders, the latter in particular to disable slot-specific I/O
decoding that otherwise remains active even in the board is disabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ESIC's memory area 1 (MEMCS1) and its Memory Address High Compare
and Memory Address Low Compare registers to set up the MMIO range for
decoding accesses to PDQ ASIC registers.  Previously the PDQ ASIC was
thought to be addressable with the memory area 0 (MEMCS0) and its Memory
Address Compare and Memory Address Mask registers.

The MMIO range allocated for the option card is preset via ECU (EISA
Configuration Utility) and can be disabled, so handle such a case
gracefully too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correctly propagate the error code from `pci_enable_device' if non zero.
Currently a failure of this function is correctly recognized and device
initialization abandoned, however a successful completion code returned.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a6111d3c "vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device"
intended to enable hardware time stamping on VLAN interfaces, but
passing SIOCSHWTSTAMP is only half of the story. This patch adds
the second half, by letting user space find out the time stamping
capabilities of the device backing a VLAN interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c3ae62af ("tcp: should drop incoming frames without ACK
flag set") was created to mitigate a security vulnerability in which a
local attacker is able to inject data into locally-opened sockets by
using TCP protocol statistics in procfs to quickly find the correct
sequence number.

This broke the RFC5961 requirement to send a challenge ACK in response
to spurious RST packets, which was subsequently fixed by commit
7b514a88 ("tcp: accept RST without ACK flag").

Unfortunately, the RFC5961 requirement that spurious SYN packets be
handled in a similar manner remains broken.

RFC5961 section 4 states that:

   ... the handling of the SYN in the synchronized state SHOULD be
   performed as follows:

   1) If the SYN bit is set, irrespective of the sequence number, TCP
      MUST send an ACK (also referred to as challenge ACK) to the remote
      peer:

      <SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>

      After sending the acknowledgment, TCP MUST drop the unacceptable
      segment and stop processing further.

   By sending an ACK, the remote peer is challenged to confirm the loss
   of the previous connection and the request to start a new connection.
   A legitimate peer, after restart, would not have a TCB in the
   synchronized state.  Thus, when the ACK arrives, the peer should send
   a RST segment back with the sequence number derived from the ACK
   field that caused the RST.

   This RST will confirm that the remote peer has indeed closed the
   previous connection.  Upon receipt of a valid RST, the local TCP
   endpoint MUST terminate its connection.  The local TCP endpoint
   should then rely on SYN retransmission from the remote end to
   re-establish the connection.

This patch lets SYN packets through the discard added in c3ae62af,
so that spurious SYN packets are properly dealt with as per the RFC.

The challenge ACK is sent unconditionally and is rate-limited, so the
original vulnerability is not reintroduced by this patch.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.

By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.

We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-11-20

This series contains updates to ixgbevf, i40e and i40evf.

Emil updates ixgbevf with much of the work that Alex Duyck did while at
Intel.  First updates the driver to clear the status bits on allocation
instead of in the cleanup routine, this way we can leave the recieve
descriptor rings as a read only memory block until we actually have
buffers to give back to the hardware.  Clean up ixgbevf_clean_rx_irq()
by creating ixgbevf_process_skb_field() to merge several similar
operations into this new function.  Cleanup temporary variables within
the receive hot-path and reducing the scope of variables that do not
need to exist outside the main loop.  Save on stack space by just
storing our updated values back in next_to_clean instead of using
a stack variable, which also collapses the size the function.  Improve
performace on IOMMU enabled systems and reduce cache misses by changing
the basic receive patch for ixgbevf so that instead of receiving the
data into an skb, it is received into a double buffered page.  Add
netpoll support by creating ixgbevf_netpoll(), which is a callback for
.ndo_poll_controller to allow for the VF interface to be used with
netconsole.

Mitch provides several cleanups and trivial fixes for i40e and i40evf.
First is a fix the overloading of the msg_size field in the
arq_event_info struct by splitting the field into two and renaming to
indicate the actual function of each field.  Updates code comments
to match the actual function.  Cleanup several checkpatch.pl warnings
by adding or removing blank lines, aligning function parameters, and
correcting over-long lines (which makes the code more readable).

Shannon provides a patch for i40e to write the extra bits that will
turn off the ITR wait for the interrupt, since we want the SW INT to
go off as soon as possible.

v2: updated patch 07 based on feedback from Alex Duyck by
 - adding pfmemalloc check to a new function for reusable page
 - moved atomic_inc outside of #if/else in ixgbevf_add_rx_frag()
 - reverted the removal of the API check in ixgbevf_change_mtu()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>