- 09 Oct, 2017 2 commits
-
-
Fabrizio Castro authored
This patch adds a .dtsi that describes the camera daughter board and a .dts to describe the HW made of iWave's RZ/G1M SoM, iWave's RZ/G1M/G1N Qseven carrier board, and the camera daughter board. The camera daughter board .dtsi adds support for ttySC[14]. Signed-off-by:
Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by:
Chris Paterson <chris.paterson2@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Fabrizio Castro authored
Since the same carrier board may host RZ/G1M and RZ/G1N based Systems on Module, the DT architecture for iwg20d-q7 needs better decoupling. This patch provides: * iwg20d-q7-common.dtsi - its purpose is to define the carrier board definitions, and its content is basically the same as the previous version of r8a7743-iwg20d-q7.dts, only it has no reference to the SoM .dtsi, and that's why the filename doesn't mention the SoC name any more. * r8a7743-iwg20d-q7.dts - its new purpose is to put together the SoM .dtsi (r8a7743-iwg20m.dtsi) and the carrier board .dtsi defined by this very patch, along with "model" and "compatible" properties. The final DT architecture to describe the board is now: r8a7743-iwg20d-q7.dts # Carrier Board + SoM ├── r8a7743-iwg20m.dtsi # SoM │ └── r8a7743.dtsi # SoC └── iwg20d-q7-common.dtsi # Carrier Board and maximizes the reuse of the definitions for the carrier board and for the SoM. Signed-off-by:
-
- 06 Oct, 2017 4 commits
-
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
- 05 Oct, 2017 2 commits
-
-
Jacopo Mondi authored
MTU2 multi-function/multi-channel timer/counter is not enabled for GR-Peach board. The timer is used as clock event source to schedule wake-ups, and without this enabled all sleeps not performed through busy waiting hang the board. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by:
-
Jacopo Mondi authored
Fix 'leds' node name indent as it was wrongly aligned. Signed-off-by:
-
- 28 Sep, 2017 2 commits
-
-
Fabrizio Castro authored
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi. Also, define aliases for spi[123]. Signed-off-by:
-
Fabrizio Castro authored
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi. Also, define aliases for spi[123]. Signed-off-by:
-
- 25 Sep, 2017 1 commit
-
-
Fabrizio Castro authored
Enable the SDHI0 controller on iWave RZ/G1E carrier board. Signed-off-by:
-
- 21 Sep, 2017 5 commits
-
-
Fabrizio Castro authored
Add support for the SPI NOR device used to boot up the system to the System on Module DT. Signed-off-by:
-
Fabrizio Castro authored
Add the DT node for the QSPI interface to the SoC dtsi. Signed-off-by:
-
Fabrizio Castro authored
Add support for the SPI NOR device used to boot up the system to the System on Module DT. Signed-off-by:
-
Fabrizio Castro authored
Add the DT node for the QSPI interface to the SoC dtsi. Signed-off-by:
-
Fabrizio Castro authored
Enable the SDHI1 controller on iWave RZ/G1E SoM. Signed-off-by:
-
- 19 Sep, 2017 24 commits
-
-
Fabrizio Castro authored
Add the SDHI controllers to the r8a7745 device tree. Signed-off-by:
-
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, but audio is not yet enabled in r8a7792.dtsi, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Biju Das authored
Signed-off-by:
Biju Das <biju.das@bp.renesas.com> Signed-off-by:
-
Wolfram Sang authored
The WP pins are ACTIVE_HIGH, fix it in the DTS. Fixes: 2b41091b ("ARM: dts: alt: add SDHI0 and 1 support") Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Biju Das authored
Signed-off-by:
-
Biju Das authored
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to them. Signed-off-by:
-
Biju Das authored
Describe the PCI USB devices that are behind the PCI bridges, adding necessary links to the USB PHY device. Signed-off-by:
-
Biju Das authored
Define the r8a7743 generic part of the USB PHY device node. Signed-off-by:
-
Biju Das authored
Add device nodes for the r8a7743 internal PCI bridge devices. Signed-off-by:
-
Biju Das authored
Define the iWave RainboW-G22D board dependent part of the Ethernet AVB device node. On some older versions of the platform (before R4.0) the phy address may be 1 or 3. The address is fixed to 3 for R4.0 onwards (which will be the first mainstream release), hence using 3 in the dts. Signed-off-by:
-
Biju Das authored
Adding pinctrl support for scif4 interface. Signed-off-by:
-
Biju Das authored
Define the iWave RainboW-G20D-Qseven board dependent part of the RTC device node. Signed-off-by:
-
Biju Das authored
Signed-off-by:
-
Biju Das authored
Add Ethernet AVB support for r8a7745 SoC. Signed-off-by:
-
Jacopo Mondi authored
Add device nodes for user leds on gr-peach board. Signed-off-by:
-
Jacopo Mondi authored
Add pin configuration subnode for SCIF2 serial debug interface. Signed-off-by:
-
Jacopo Mondi authored
Remove an empty line in gr-peach device tree source file. Signed-off-by:
-
Geert Uytterhoeven authored
The current practice is to not group clocks under a "clocks" subnode, but just put them together with the other on-SoC devices. Signed-off-by:
-
Geert Uytterhoeven authored
Convert the R-Car M2-W SoC from the old "Renesas R-Car Gen2 Clock Pulse Generator (CPG)", "Renesas CPG DIV6 Clock", and "Renesas CPG Module Stop (MSTP) Clocks" DT bindings to the new unified "Renesas Clock Pulse Generator / Module Standby and Software Reset" DT bindings. This simplifies the DTS files, and allows to add support for reset control later. Signed-off-by:
-
Fabrizio Castro authored
Add support for the bq32000 RTC to the iwg22m device tree. Signed-off-by:
-
