- 26 Dec, 2008 40 commits
-
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/qlge/qlge_ethtool.c:100:6: warning: symbol 'ql_update_stats' was not declared. Should it be static? drivers/net/qlge/qlge_mpi.c:22:5: warning: symbol 'ql_get_mb_sts' was not declared. Should it be static? Signed-off-by:
Hannes Eder <hannes@hanneseder.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/netxen/netxen_nic_hw.c:1462:18: warning: Using plain integer as NULL pointer drivers/net/netxen/netxen_nic_hw.c:1536:18: warning: Using plain integer as NULL pointer Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/ixgbe/ixgbe_82598.c:180:5: warning: symbol 'ixgbe_get_copper_link_capabilities_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:245:5: warning: symbol 'ixgbe_setup_fc_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:729:5: warning: symbol 'ixgbe_set_vmdq_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:773:5: warning: symbol 'ixgbe_set_vfta_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:897:5: warning: symbol 'ixgbe_read_analog_reg8_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:919:5: warning: symbol 'ixgbe_write_analog_reg8_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:940:5: warning: symbol 'ixgbe_read_i2c_eeprom_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:1000:5: warning: symbol 'ixgbe_get_supported_physical_layer_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_dcb_82598.c:100:5: warning: symbol 'ixgbe_dcb_config_packet_buffers_82598' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/irda/ma600-sir.c:239:5: warning: symbol 'ma600_reset' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:875:5: warning: symbol 'smsc_ircc_hard_xmit_sir' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:1131:6: warning: symbol 'smsc_ircc_set_sir_speed' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:1897:6: warning: symbol 'smsc_ircc_sir_start' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:150:5: warning: symbol 'w83977af_open' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:313:5: warning: symbol 'w83977af_probe' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:412:6: warning: symbol 'w83977af_change_speed' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:492:5: warning: symbol 'w83977af_hard_xmit' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:734:5: warning: symbol 'w83977af_dma_receive' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:806:5: warning: symbol 'w83977af_dma_receive_complete' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this warning: drivers/net/igb/e1000_mac.c:54: warning: 'igb_read_pci_cfg' defined but not used Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Hannes Eder authored
Fix this sparse warning: drivers/net/enic/vnic_dev.c:288:5: warning: symbol 'vnic_dev_capable' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/e1000e/es2lan.c:1265:5: warning: symbol 'e1000_read_kmrn_reg_80003es2lan' was not declared. Should it be static? drivers/net/e1000e/es2lan.c:1298:5: warning: symbol 'e1000_write_kmrn_reg_80003es2lan' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
The function 'vsc8211_set_speed_duplex' is not used, so comment it out. For 'vsc8211_set_automdi' the function 'vsc8211_set_speed_duplex' is the only caller, so comment it out as well. Fix this (sparse) warning: drivers/net/cxgb3/vsc8211.c:269: warning: 'vsc8211_set_automdi' defined but not used drivers/net/cxgb3/vsc8211.c:295:5: warning: symbol 'vsc8211_set_speed_duplex' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/bonding/bond_main.c:104:20: warning: symbol 'bonding_defaults' was not declared. Should it be static? drivers/net/bonding/bond_main.c:204:22: warning: symbol 'ad_select_tbl' was not declared. Should it be static? drivers/net/bonding/bond_sysfs.c:60:21: warning: symbol 'bonding_rwsem' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/atlx/atl1.c:198:16: warning: symbol 'atl1_check_options' was not declared. Should it be static? drivers/net/atlx/atl1.c:526:5: warning: symbol 'atl1_read_mac_addr' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/arcnet/capmode.c:64:6: warning: symbol 'arcnet_cap_init' was not declared. Should it be static? drivers/net/arcnet/com90xx.c:586:5: warning: symbol 'com90xx_reset' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warnings: drivers/net/3c523.c:350:6: warning: symbol 'alloc586' was not declared. Should it be static? drivers/net/cs89x0.c:1029:14: warning: symbol 'reset_chip' was not declared. Should it be static? drivers/net/eepro.c:1399:1: warning: symbol 'read_eeprom' was not declared. Should it be static? drivers/net/plip.c:1020:5: warning: symbol 'plip_hard_header_cache' was not declared. Should it be static? drivers/net/s2io.c:5116:6: warning: symbol 'do_s2io_store_unicast_mc' was not declared. Should it be static? drivers/net/smc9194.c:767:12: warning: symbol 'smc_findirq' was not declared. Should it be static? Signed-off-by:
-
Hannes Eder authored
Fix this sparse warning: drivers/net/niu.c:8850:2: warning: returning void-valued expression Signed-off-by:
-
Hannes Eder authored
While at it insert some extra curly braces and fix formatting. Fix this sparse warnings: drivers/net/atp.c:811:8: warning: do-while statement is not a compound statement drivers/net/atp.c:813:8: warning: do-while statement is not a compound statement drivers/net/atp.c:815:11: warning: do-while statement is not a compound statement drivers/net/atp.c:817:11: warning: do-while statement is not a compound statement drivers/net/plip.c:642:4: warning: do-while statement is not a compound statement drivers/net/plip.c:647:4: warning: do-while statement is not a compound statement drivers/net/plip.c:820:4: warning: do-while statement is not a compound statement drivers/net/plip.c:825:4: warning: do-while statement is not a compound statement drivers/net/starfire.c:886:3: warning: do-while statement is not a compound statement Signed-off-by:
-
Hannes Eder authored
Fix this sparse warning: drivers/net/ne.c:932:24: warning: non-ANSI function declaration of function 'init_module' Signed-off-by:
-
Nathan Lynch authored
With slub debug enabled, I see the following errors and crash with 2.6.28-rc9: IBM eHEA ethernet device driver (Release EHEA_0095) ehea: Error in ehea_h_register_rpage_mr: not on pageboundary ehea: Error in ehea_reg_mr_section: register_rpage_mr failed ehea: Error in ehea_reg_kernel_mr: registering mr failed ehea: Error in ehea_setup_ports: creating MR failed ehea 23c00100.lhea: setup_ports failed Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6bbdcb Faulting instruction address: 0xd000000000064a24 cpu 0x0: Vector: 300 (Data Access) at [c0000000740e7190] pc: d000000000064a24: .ehea_update_firmware_handles+0x84/0x47c [ehea] lr: d00000000006df34: .ehea_probe_adapter+0x35c/0x39c [ehea] sp: c0000000740e7410 msr: 8000000000009032 dar: 6b6b6b6b6b6bbdcb dsisr: 40000000 current = 0xc000000074233780 paca = 0xc0000000008a3300 pid = 2046, comm = modprobe enter ? for help [c0000000740e74f0] d00000000006df34 .ehea_probe_adapter+0x35c/0x39c [ehea] [c0000000740e75a0] c00000000041d5a4 .of_platform_device_probe+0x78/0xb0 [c0000000740e7630] c0000000002d8b38 .driver_probe_device+0x13c/0x200 [c0000000740e76c0] c0000000002d8c90 .__driver_attach+0x94/0xd8 [c0000000740e7750] c0000000002d7d64 .bus_for_each_dev+0x80/0xd8 [c0000000740e7800] c0000000002d889c .driver_attach+0x28/0x40 [c0000000740e7880] c0000000002d8340 .bus_add_driver+0xd4/0x284 [c0000000740e7920] c0000000002d90a0 .driver_register+0xc4/0x198 [c0000000740e79d0] c00000000041d45c .of_register_driver+0x4c/0x60 [c0000000740e7a50] c000000000020ef8 .ibmebus_register_driver+0x30/0x4c [c0000000740e7ae0] d00000000006e108 .ehea_module_init+0x194/0x208c [ehea] [c0000000740e7b90] c000000000009028 .do_one_initcall+0x90/0x1ac [c0000000740e7d90] c00000000008619c .sys_init_module+0xc4/0x200 [c0000000740e7e30] c0000000000084ac syscall_exit+0x0/0x40 (When slub debug is disabled it works fine.) PAGE_SIZE allocations via slab are not guaranteed to be page-aligned; use get_zeroed_page for the 'pt' buffer (I don't really know what this is, only that it is passed to firmware and that the first error message complains about its alignment). This allows the system to boot. Signed-off-by:Nathan Lynch <ntl@pobox.com> Signed-off-by:
-
Yevgeny Petrilin authored
They are controlled through Ethtool interface. Signed-off-by:
Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by:
-
Yevgeny Petrilin authored
They are controlled through Ethtool interface, no need to have two ways to modify them. Signed-off-by:
-
Yevgeny Petrilin authored
Signed-off-by:
-
Yevgeny Petrilin authored
There is no need to synchronize the polling with the transmit function. The only place to synchronize is when we process the cq from the transmit function. Also removed spin_lock_irq, and using spin_trylock, if somebody else is already processing the cq, no need to wait for it to finish. Signed-off-by:
-
Yevgeny Petrilin authored
If port is being destroyed without being activated before, CQ resources are not freed. Signed-off-by:
-
-
Brice Goglin authored
Update myri10ge driver version to 1.4.4-1.395. Signed-off-by:
Brice Goglin <brice@myri.com> Signed-off-by:
-
Brice Goglin authored
Update myri10ge firmware headers to 1.4.37: * Make each member of the error/cmd enum an initialized one, so there is a convenient numerical reference to look for reverse conversion. * Add new MXGEFW_CMD_RELAX_RXBUFFER_ALIGNMENT command. * Add new "features" field to mcp_header. Signed-off-by:
-
Johannes Berg authored
Polling doesn't seem to be necessary on my hardware, at least I haven't seen any bad effects testing it a while. Remove the polling so the CPU doesn't have to wake up a hundred times per second. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Julia Lawall authored
atif is tested for being NULL twice, with the same effect in each case. I have kept the second test, as it seems to fit well with the comment above it. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Julia Lawall authored
arg is checked not to be NULL a few lines before. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by:
-
Julia Lawall authored
In each case, ap is checked not to be NULL a few lines before. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by:
-
Julia Lawall authored
In each case, vpage is checked not to be NULL just after it is initialized at the beginning of each loop iteration. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by:
-
Julia Lawall authored
phydev is checked to be not NULL a few lines above. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by:
-
Roel Kluin authored
Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
Ron Mercer <ron.mercer@qlogic.com> Signed-off-by:
-
Vegard Nossum authored
See commit 1045b03e ("netlink: fix overrun in attribute iteration") for a detailed explanation of why this patch is necessary. In short, nlmsg_next() can make "remaining" go negative, and the remaining >= sizeof(...) comparison will promote "remaining" to an unsigned type, which means that the expression will evaluate to true for negative numbers, even though it was not intended. I put "theoretical" in the title because I have no evidence that this can actually happen, but I suspect that a crafted netlink packet can trigger some badness. Note that the last test, which seemingly has the exact same problem (also true for nla_ok()), is perfectly OK, since we already know that remaining is positive. Signed-off-by:
Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by:
-
Herbert Xu authored
Our TCP stack does not set the urgent flag if the urgent pointer does not fit in 16 bits, i.e., if it is more than 64K from the sequence number of a packet. This behaviour is different from the BSDs, and clearly contradicts the purpose of urgent mode, which is to send the notification (though not necessarily the associated data) as soon as possible. Our current behaviour may in fact delay the urgent notification indefinitely if the receiver window does not open up. Simply matching BSD however may break legacy applications which incorrectly rely on the out-of-band delivery of urgent data, and conversely the in-band delivery of non-urgent data. Alexey Kuznetsov suggested a safe solution of following BSD only if the urgent pointer itself has not yet been transmitted. This way we guarantee that when the remote end sees the packet with non-urgent data marked as urgent due to wrap-around we would have advanced the urgent pointer beyond, either to the actual urgent data or to an as-yet untransmitted packet. The only potential downside is that applications on the remote end may see multiple SIGURG notifications. However, this would occur anyway with other TCP stacks. More importantly, the outcome of such a duplicate notification is likely to be harmless since the signal itself does not carry any information other than the fact that we're in urgent mode. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Wei Yongjun authored
The latest ietf socket extensions API draft said: 8.1.21. Set or Get the SCTP Partial Delivery Point Note also that the call will fail if the user attempts to set this value larger than the socket receive buffer size. This patch add this validity check for SCTP_PARTIAL_DELIVERY_POINT socket option. Signed-off-by:Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by:
Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by:
-
Wei Yongjun authored
If FWD-TSN chunk is received with bad stream ID, the sctp will not do the validity check, this may cause memory overflow when overwrite the TSN of the stream ID. The FORWARD-TSN chunk is like this: FORWARD-TSN chunk Type = 192 Flags = 0 Length = 172 NewTSN = 99 Stream = 10000 StreamSequence = 0xFFFF This patch fix this problem by discard the chunk if stream ID is not less than MIS. Signed-off-by:
-
Wei Yongjun authored
Implement socket option SCTP_GET_ASSOC_NUMBER of the latest ietf socket extensions API draft. 8.2.5. Get the Current Number of Associations (SCTP_GET_ASSOC_NUMBER) This option gets the current number of associations that are attached to a one-to-many style socket. The option value is an uint32_t. Signed-off-by:
-
Wei Yongjun authored
Just fix a typo in socket.c. Signed-off-by:
-
Wei Yongjun authored
Brings maxseg socket option set/get into line with the latest ietf socket extensions API draft, while maintaining backwards compatibility. Signed-off-by:
-
Krzysztof Halasa authored
The PHYLIB mdio code has more problems in error paths: - mdiobus_release can be called before bus->state is set to MDIOBUS_REGISTERED - mdiobus_scan allocates resources which need to be freed - the comment is wrong, the resistors used are actually pull-ups. Signed-off-by:
Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by:
-
Eric Dumazet authored
commit 656299f7 (vlan: convert to net_device_ops) added a net_device_ops with a NULL ndo_start_xmit field. This gives a crash in dev_hard_start_xmit() Fix it using two net_device_ops structures, one for hwaccel vlan, one for non hwaccel vlan. Signed-off-by:
Eric Dumazet <dada1@cosmosbay.com> Signed-off-by:
-
