Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX25's udc port is the same as i.MX35's one
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX25's EHCI is the same as i.MX35's one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

when CONFIG_USB_ULPI is not defined we actually get :
warning: 'otg_pdata' defined but not used
warning: 'usbh2_pdata' defined but not used
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: s.hauer@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add device registration and setup IOMUX pins in the mx51_babbage
board feil.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch adds I2C functionality to the Freescale MX51 Babbage HW.
The patch adds device structures, i2c board slave device defines,
IOMUX pin defines, and clocks.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch fixes the clock refcounting when reparenting is used.

Boot-tested on imx51 babbage board.

Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.htmlSigned-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The keymap is taken from the Freescale supplied kernel.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on work from Alberto Panizzo for MX3X
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

support copied from mach-pca100.c
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Like this one (if CONFIG_USB_ULPI is not set):

arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This makes the resistive touch interface work.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

CC      arch/arm/mach-mx3/mach-pcm037.o
  arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init':
  arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp'
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
  drivers/net/usb/asix.c: Fix pointer cast.
  be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
  proc_dointvec: write a single value
  hso: add support for new products
  Phonet: fix potential use-after-free in pep_sock_close()
  ath9k: remove VEOL support for ad-hoc
  ath9k: change beacon allocation to prefer the first beacon slot
  sock.h: fix kernel-doc warning
  cls_cgroup: Fix build error when built-in
  macvlan: do proper cleanup in macvlan_common_newlink() V2
  be2net: Bug fix in init code in probe
  net/dccp: expansion of error code size
  ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
  wireless: fix sta_info.h kernel-doc warnings
  wireless: fix mac80211.h kernel-doc warnings
  iwlwifi: testing the wrong variable in iwl_add_bssid_station()
  ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
  ath9k_htc: dereferencing before check in hif_usb_tx_cb()
  rt2x00: Fix rt2800usb TX descriptor writing.
  rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
  ...

* 'alpha-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
  alpha: simplify and optimize sched_find_first_bit
  alpha: invoke oom-killer from page fault
  Convert alpha to use clocksources instead of arch_gettimeoffset

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  driver core: add devname module aliases to allow module on-demand auto-loading

This reverts commit 480b02df, since
Rafael reports that it causes occasional kernel paging request faults in
load_module().

Dropping the module lock and re-taking it deep in the call-chain is
definitely not the right thing to do.  That just turns the mutex from a
lock into a "random non-locking data structure" that doesn't actually
protect what it's supposed to protect.
Requested-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Brandon Philips <brandon@ifup.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Stephen Rothwell reports the following new warning:

drivers/net/usb/asix.c: In function 'asix_rx_fixup':
drivers/net/usb/asix.c:325: warning: cast from pointer to integer of different size
drivers/net/usb/asix.c:354: warning: cast from pointer to integer of different size

The code just cares about the low alignment bits, so use
an "unsigned long" cast instead of one to "u32".
Signed-off-by: David S. Miller <davem@davemloft.net>