- 26 Jul, 2010 39 commits
-
-
Jason Wang authored
For pad EIM_D27 to work in UART3_RTS mode, the input path should be 3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux value should be 2 instead of 8. Signed-off-by:
Jason Wang <jason77.wang@gmail.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Amit Kucheria authored
The pads capable of being used as GPIOs had their pad-name and mode-name switched. Also, fix the following: - Whitespace fixes - Replace IOMUX_CONFIG_ALTn with 'n' Signed-off-by:
Amit Kucheria <amit.kucheria@canonical.com> Signed-off-by:
-
Eric Bénard authored
* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host, USB OTG and I2C touchscreen controller * mbimxsd provides access to LCD, Audio, LED, Switch button, UART ... Signed-off-by:
Eric Bénard <eric@eukrea.com> Signed-off-by:
-
Baruch Siach authored
The information in the i.MX25 Reference Manual is lacking. Add information from the Freescale BSP. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Acked-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Eric Bénard authored
* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host and USB OTG * mbimxsd provides access to LCD, Audio, LED, Switch button, UART ... Signed-off-by:
-
Eric Bénard authored
* add clocks for audmux and ssi 1 & 2 * add irq for ssi 1 & 2 * add devices platform for ssi1 & 2 * update audmux-v2 for i.MX25 * add base addresses for audmux & ssi 1 & 2 * add iomux configuration for GPIO for AUD5 port Signed-off-by:
-
Eric Bénard authored
i.MX25's udc port is the same as i.MX35's one Signed-off-by:
-
Eric Bénard authored
i.MX25's EHCI is the same as i.MX35's one. Signed-off-by:
-
Eric Bénard authored
usb drivers need to get the right value for otg clock so calculate and return it Signed-off-by:
-
Eric Bénard authored
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse most of the i.MX35's defines. Signed-off-by:
-
Eric Bénard authored
the standard place for this define is include/mach/mx25.h Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
when CONFIG_USB_ULPI is not defined we actually get : warning: 'otg_pdata' defined but not used warning: 'usbh2_pdata' defined but not used Signed-off-by:
-
Eric Bénard authored
without this patch, ipu_clk's value is 0 thus preventing mx3fb from calculating the right divisor for pixel clock generator. Signed-off-by:
-
Dinh Nguyen authored
Add device registration and setup IOMUX pins in the mx51_babbage board feil. Signed-off-by:
Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by:
-
Dinh Nguyen authored
This patch adds I2C functionality to the Freescale MX51 Babbage HW. The patch adds device structures, i2c board slave device defines, IOMUX pin defines, and clocks. Signed-off-by:
-
Amit Kucheria authored
This patch fixes the clock refcounting when reparenting is used. Boot-tested on imx51 babbage board. Sascha pointed out a good explanation of refcounting here: http://www.spinics.net/lists/arm-kernel/msg85879.htmlSigned-off-by:
-
Baruch Siach authored
The keymap is taken from the Freescale supplied kernel. Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Sascha Hauer authored
The OOB handling in the mxc_nand driver is broken for v1 type controllers (i.MX27/31) with 512 byte page size. This perhaps did not show up because ubi does not use OOB. Update the driver to always read/write a whole page even if only OOB is requested. With this patch the driver passes the mtd_oobtest on i.MX27 with 512 byte page size. Also tested with 2048 byte page size and on i.MX35 (v2 type controller) Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Based on work from Alberto Panizzo for MX3X Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
support copied from mach-pca100.c Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Wolfram Sang authored
Like this one (if CONFIG_USB_ULPI is not set): arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used Signed-off-by:
-
Daniel Mack authored
This makes the resistive touch interface work. Signed-off-by:
Daniel Mack <daniel@caiaq.de> Signed-off-by:
-
- 26 May, 2010 1 commit
-
-
Daniel Mack authored
CC arch/arm/mach-mx3/mach-pcm037.o arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init': arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp' Signed-off-by:
-
