This is the first step in the transition from the vPort model to a
unified Port-VLAN structure. The new structure is defined and created /
destroyed upon invocation of the 8021q ndos, but it's not actually used
throughout the code.

Subsequent patches will initialize it correctly and also create /
destroy it upon switchdev's VLAN object.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently transition the port to "Virtual mode" upon the creation of
its first VLAN upper, as we need to classify incoming packets to a FID
using {Port, VID} and not only the VID.

However, it's more appropriate to transition the port to this mode when
the {Port, VID} are actually mapped to a FID. Either during the
enslavement of the VLAN upper to a VLAN-unaware bridge or the
configuration of a router port.

Do this change now in preparation for the introduction of the FID core,
where this operation will be encapsulated.

To prevent regressions, this patch also explicitly configures an OVS
slave to "Virtual mode". Otherwise, a packet that didn't hit an ACL rule
could be classified to an existing FID based on a global VID-to-FID
mapping, thus not incurring a FID mis-classification, which would
otherwise trap the packet to the CPU to be processed by the OVS daemon.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During enslavement to a bridge, after the CHANGEUPPER is sent, the
multicast enabled state of the bridge isn't propagated down to the
offloading driver unless it's changed.

This patch allows such drivers to query the multicast enabled state from
the bridge, so that they'll be able to correctly configure their flood
tables during port enslavement.

In case multicast is disabled, unregistered multicast packets can be
treated as broadcast and be flooded through all the bridge ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's useful for drivers supporting bridge offload to be able to query
the bridge's VLAN filtering state.

Currently, upon enslavement to a bridge master, the offloading driver
will only learn about the bridge's VLAN filtering state after the bridge
device was already linked with its slave.

Being able to query the bridge's VLAN filtering state allows such
drivers to forbid enslavement in case resource couldn't be allocated for
a VLAN-aware bridge and also choose the correct initialization routine
for the enslaved port, which is dependent on the bridge type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
net: dsa: mv88e6xxx: Add basic SERDES support

Some of the Marvell switches are SERDES interface, which must be
powered up before packets can be passed. This is particularly true on
the 6390, where the SERDES defaults to down, probably to save power.

This series refactors the existing SERDES support for the 6352, and
adds 6390 support.

v2:

Split phy functions out into phy.[ch]
Don't add MV88E6XXX_FLAG_G1_ATU_FID back again
Move the serdes op up in mv88e6xxx_ops
Move some #defines into serdes.h
Add a mv88e6xxx_serdes_power()
Don't keep moving calls to this helper around in the code

v3:

Move more phy functions into phy.[ch]
Make mv88e6xxx_phy_page_get() and mv88e6xxx_phy_page_put static
Use the mv88e6xxx_serdes_power() helper everywhere
dev_err(...) when mv88e6xxx_serdes_power() fails
Add reviewed-by's
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the port enable/disable callbacks, which enable/disable the
SERDES interfaces, if applicable. This should save a bit of
power/heat.

We also need to enable SERDES on CPU and DSA ports, so keep the
existing call to the op, but make it conditional.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6390X family has 8 SERDES lanes. These can be used for 2
10Gbps ports, ports 9 or 10. If these ports are used at slower speeds,
the SERDES lanes become available for other ports for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we use an op for SERDES operations, we don't need a flag for
it. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6390 family has a different SERDES implementation. Refactor
the mv88e6352 code into an ops function, so we can later add the
mv88e6390 code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The upcoming SERDES support will need to make use of PHY functions. Move
them out into a file of there own. No code changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of falling back to 00:00:00:00:00:00 generate a random address
if none is provided via platform data or from the device's register
space.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
More marvell phy cleanups

This patchset continues the cleanup of the Marvell PHY driver.  These
phys use pages to allow more than the 32 registers that fit into the
MDIO address space. Cleanup the code used for changing pages.

v2
Reverse christmas tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Bring all the page names together, remove the repeats, and make them
uniform.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a common pattern of first reading the currently selected page
and then changing to another page. Add a helper to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

EXT_ADDR_PAGE is the same meaning as MII_MARVELL_PHY_PAGE, i.e. change
page. Replace it will calls to the helpers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace magic numbers for PHY pages with symbolic names.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

lio_enable_irq (called by napi poll) is reporting to Octeon an inaccurate
count of processed rx packets causing Octeon to eventually stop forwarding
packets to the host.  Fix it by using this formula for an accurate count:

    processed rx packets = droq->pkt_count - droq->pkts_pending

Also increase SOFT_COMMAND_BUFFER_SIZE to match what the firmware expects.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a rare pci_driver.probe failure of the VF driver that's caused by
PF/VF handshake going out of sync.  The culprit is octeon_mbox_write() who
ignores an ack timeout condition; it just keeps unconditionally writing all
elements of mbox_cmd->data[] even when the other side is not ready for
them.  Fix it by making each write of mbox_cmd->data[i] conditional to
having previously received an ack.

Also fix the octeon_mbox_state enum such that each state gets a unique
value.  Also add ULL suffix to numeric literals in macro definitions.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: Create sysfs reciprocal links for attached_dev/phydev

This patch series addresses a device topology shortcoming where a program
scanning /sys would not be able to establish a mapping between the network
device and the PHY device.

In the process it turned out that no PHY device documentation existed for
sysfs attributes.

Changes in v2:

- document possible phy_interface values in sysfs-class-net-phydev
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the different sysfs attributes that exist for PHY devices:
attached_dev, phy_has_fixups, phy_id and phy_interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we link the network device to its PHY device, document this
sysfs symbolic link.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is currently no way for a program scanning /sys to know whether a
network device is attached to a particular PHY device, just like the PHY
device is not pointed back to its attached network device.

Create a symbolic link in the network device's namespace named "phydev"
which points to the PHY device and create a symbolic link in the PHY
device's namespace named "attached_dev" that points back to the network
device. These links are set up during phy_attach_direct() and removed
during phy_detach() for symetry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
net: extend RTM_GETROUTE to return fib result

This series adds a new RTM_F_FIB_MATCH flag to return matched fib result
with RTM_GETROUTE. This is useful for applications and protocols in
userspace wanting to query the selected route.

examples (with patched iproute2):
ipv4:
----
$ip route show
default via 192.168.0.2 dev eth0
10.0.14.0/24
        nexthop via 172.16.0.3  dev dummy0 weight 1
        nexthop via 172.16.1.3  dev dummy1 weight 1

$ip route get 10.0.14.2
10.0.14.2 via 172.16.1.3 dev dummy1  src 172.16.1.1
    cache

$ip route get fibmatch 10.0.14.2
10.0.14.0/24
        nexthop via 172.16.0.3  dev dummy0 weight 1
        nexthop via 172.16.1.3  dev dummy1 weight 1

ipv6:
----
$ip -6 route show
2001:db9:100::/120  metric 1024
        nexthop via 2001:db8:2::2  dev dummy0 weight 1
        nexthop via 2001:db8:12::2  dev dummy1 weight 1

$ip -6 route get 2001:db9:100::1
2001:db9:100::1 from :: via 2001:db8:12::2 dev dummy1  src 2001:db8:12::1  metric 1024  pref medium

$ip -6 route get fibmatch 2001:db9:100::1
2001:db9:100::/120  metric 1024
        nexthop via 2001:db8:12::2  dev dummy1 weight 1
        nexthop via 2001:db8:2::2  dev dummy0 weight 1

v2:
        - pick up new forward port of patch-01 from david
        - inet6_rtm_getroute: use container_of for rt6_info to
          dst conversion
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support to return matched fib result when RTM_F_FIB_MATCH
flag is specified in RTM_GETROUTE request. This is useful for user-space
applications/controllers wanting to query a matching route.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support to return matched fib result when RTM_F_FIB_MATCH
flag is specified in RTM_GETROUTE request. This is useful for user-space
applications/controllers wanting to query a matching route.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This flag when specified will return matched fib result in
response to a RTM_GETROUTE query.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix is needed for returning matching route spec on get route request.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert inet_rtm_getroute to use ip_route_input_rcu and
ip_route_output_key_hash_rcu passing the fib_result arg to both.
The rcu lock is held through the creation of the response, so the
rtable/dst does not need to be attached to the skb and is passed
to rt_fill_info directly.

In converting from ip_route_output_key to ip_route_output_key_hash_rcu
the xfrm_lookup_route in ip_route_output_flow is dropped since
flowi4_proto is not set for a route get request.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rt_fill_info has 1 caller with the event set to RTM_NEWROUTE. Given that
remove the arg and use RTM_NEWROUTE directly in rt_fill_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A later patch wants access to the fib result on an input route lookup
with the rcu lock held. Refactor ip_route_input_noref pushing the logic
between rcu_read_lock ... rcu_read_unlock into a new helper that takes
the fib_result as an input arg.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A later patch wants access to the fib result on an output route lookup
with the rcu lock held. Refactor __ip_route_output_key_hash, pushing
the logic between rcu_read_lock ... rcu_read_unlock into a new helper
with the fib_result as an input arg.

To keep the name length under control remove the leading underscores
from the name and add _rcu to the name of the new helper indicating it
is called with the rcu read lock held.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: devlink port implementation

This series adds basic devlink support.  The operations we can perform
are port show and port split/unsplit.

v2:
Register devlink first, and then register all the ports.  Port {,un}split
searches the port list, which is protected by a mutex.  If port split
is requested before ports are registered we will simply not find the port
and return -EINVAL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for configuring port split with devlink.  Add devlink
callbacks to validate requested config and call NSP helpers.
Getting the right nfp_port structure can be done with simple iteration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For port splitting we will need to know the total number of lanes
in a port.  Calculate that based on eth_table information.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend nfp_port to contain devlink_port structures.  Register the
ports to allow users inspecting device ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will soon have to invoke more clean up for vNICs.
Move the cleanup callbacks into a helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add initial devlink support.  This patch simply switches allocation
of per-adapter structure to devlink's priv and register devlink
with empty ops table.  See following patches for implementation
of particular ops.

We should now clear the app pointer on exit, this is how devlink
callbacks will know app is not initialized.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move mutex init to main file close to structure allocation.
This will allow mutex to be taken before net code runs (e.g.
from devlink callbacks).  While at it remember to destroy
the mutex.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Support firmware flash

Add support for device firmware flash on mlxsw spectrum. The firmware files
are expected to be in the Mellanox Firmware Archive version 2 (MFA2)
format.

The firmware flash is triggered on driver initialization time if the device
firmware version does not meet the minimum firmware version supported by
the driver.

Currently, to activate the newly flashed firmware, the user needs to
reboot his system.

The first patch introduces the mlxfw module, which implements common logic
needed for the firmware flash process on Mellanox products, such as the
MFA2 format parsing and the firmware flash state machine logic. As the
module implements common logic which will be needed by various different
Mellanox drivers, it defines a set of callbacks needed to interact with the
specific device.

Patches 1-5 implement the needed mlxfw callbacks in the mlxsw spectrum
driver.

Patches 6 and 7 add boot-time firmware upgrade on the mlxsw spectrum
driver.

Patch 8 adds a fix needed for new firmware versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In new firmware versions, when configuring a {Port, VID} as a router
interface, the driver is responsible for enabling the STP filter and
disabling learning.  Otherwise, packets are discarded.

This change doesn't break existing firmware versions, but is required
for newer firmware versions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>