On some platforms, for example where we are doing the bring-up,
the csr clock is not passed from the framework and the Ethernet
device driver is failing when it can work w/o any issues and
using the default values. So this patch just warnings the case
of the csr clock cannot be acquired but w/o failing the probe
step. I have just tested it on ST STiH415 SoC (ARM).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently the dma parameters that can be passed from the platform
have been moved from the plat_stmmacenet_data to the stmmac_dma_cfg.

In case of this new structure is not well allocated the driver can
fails. This is an example how this field is managed in ST platforms

static struct stmmac_dma_cfg gmac_dma_setting = {
        .pbl = 32,
};

static struct plat_stmmacenet_data stih415_ethernet_platform_data[] = {
	{
		.dma_cfg = &gmac_dma_setting,
		.has_gmac = 1,
[snip]

This patch so verifies that the dma_cfg passed from the platform.
In case of it is NULL there is no reason that the driver has to fail
and some default values can be passed. These are ok for all the
Synopsys chips and could impact on performances, only.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
cc: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the mdio_register/_unregister in probe/remove
functions and this also is required when hibernation on disk
is done.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st,com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st,com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Freeze and restore can call the custom init/exit functions.
Also the patch adds a custom data field that can be used
for storing platform data useful on restore the embedded
setup (e.g. GPIO, SYSCFG).
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.

MVM doesn't have to use this declaration.

CC: netdev@vger.kernel.org
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize slave device link state as down if ARP monitor is
active and net_carrier_ok() returns zero. Also shift initial
value of its last_arp_tx so that it doesn't immediately cause
fake detection of "up" state.

When ARP monitoring is used, initializing the slave device with
up link state can cause ARP monitor to detect link failure
before the device is really up (with igb driver, this can take
more than two seconds).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put use & mask on same location to avoid two holes on 64bit arches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When defragmentation is finalized, we clone a packet and kfree_skb() it.

Call consume_skb() to not confuse dropwatch, since its not a drop.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of GRO processing, merged skbs should be consumed, not freed, to
not confuse dropwatch/drop_monitor.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we need to clone skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we need to reallocate skb, we dont drop a packet.
Call consume_skb() to not confuse dropwatch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core/sysctl_net_core.c: In function ‘sysctl_core_init’:
net/core/sysctl_net_core.c:259: error: implicit declaration of function ‘kmemleak_not_leak’

with same error in net/ipv4/route.c
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in some platforms, we found the max-read-request-size in Device Control
Register is set to 0 by (BIOS?) during bootup, this will cause the
performance(throughput) very bad.
Restore it to a min-value.
register definition of REG_DEVICE_CTRL is removed, using kernel API to
access it as it's a standard pcie register.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

using fixed TXQ config for l2cb and l1c regardless dmar_block
to make tx-DMA more stable.
register REG_TXQ_CTRL is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dmaw_block is never used in the driver, remove it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

some fields of REG_DMA_CTRL(15C0) are wrong, replace with the newest one.
haredware uses fixed dma-write-block size, remove dmaw_block related code
in function atl1c_configure_dma.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

function atl1c_stop_mac uses wrong register of REG_TWSI_CTRL
to stop mac, replace it with REG_TXQ_CTRL.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove code related to rxq 1/2/3 since multi-q not support.
refine REG_RXQ_CTRL definition as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TPD producer/consumer index is 16bit wide.
16bit read/write reduce the dependency of the 2 tpd rings (hi and lo)
rename reg(157C/1580) to keep name coninsistency.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l1c & later chips don't support DMA for SMB.
CMB is removed from hardware.
reg(15C8) is used to trig interrupt by tpd threshold.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to
access external NV-memory.
l1c & later chip doesn't use it any more.
PHY 0/1 registers occupy the last 2 slots of the dump table.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove HDS register as it doesn't exist in hardware.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the multiple-RX-Q in hardware doesn't work,
all related register definition & code are removed.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

replace unavailable email of the author since he left with a mail-list.
update company info as well, Atheros was acquired by Qualcomm.
insert "100" to driver description since it support 100M controller.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-testmode.c
	include/net/nfc/nfc.h
	net/nfc/netlink.c
	net/wireless/nl80211.c

Included changes:
* remove duplicated line in comment
* add htons() invocation for tt_crc as suggested by Al Viro
* OriGinator Message seqno initial value is now random
* some cleanups and fixes

When we receive an OGM from from a node for the first time, the last_real_seqno
field of the orig_node structure has not been initialised yet. The value of this
field is used to compute the current ogm-seqno window and therefore the
protection mechanism will probably drop the packet due to an out-of-window error.
To avoid this situation this patch adds a check to skip the window protection
mechanism if no neighbour nodes have already been added. When the first
neighbour node is added, the last_real_seqno field is initialised too.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

OGM sequence numbers are declared as uint32_t and so they have to printed
using %u instead of %d in order to avoid wrong representations.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Instead of using sizeof(struct ethhdr) it is strongly recommended to use the
kernel macro ETH_HLEN. This patch substitute each occurrence of the former
expressione with the latter one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

The coming protocol changes also will have a part called "OGM". That
makes it necessary to introduce a distinction in the code base.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Using BATMAN_OGM_LEN leaves one with the impression that this is
the full packet size which is not the case. Therefore the variable
is renamed.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>