Close the hole of holding a mapping over kernel driver takeover event of
a given address range.

Commit 90a545e9 ("restrict /dev/mem to idle io memory ranges")
introduced CONFIG_IO_STRICT_DEVMEM with the goal of protecting the
kernel against scenarios where a /dev/mem user tramples memory that a
kernel driver owns. However, this protection only prevents *new* read(),
write() and mmap() requests. Established mappings prior to the driver
calling request_mem_region() are left alone.

Especially with persistent memory, and the core kernel metadata that is
stored there, there are plentiful scenarios for a /dev/mem user to
violate the expectations of the driver and cause amplified damage.

Teach request_mem_region() to find and shoot down active /dev/mem
mappings that it believes it has successfully claimed for the exclusive
use of the driver. Effectively a driver call to request_mem_region()
becomes a hole-punch on the /dev/mem device.

The typical usage of unmap_mapping_range() is part of
truncate_pagecache() to punch a hole in a file, but in this case the
implementation is only doing the "first half" of a hole punch. Namely it
is just evacuating current established mappings of the "hole", and it
relies on the fact that /dev/mem establishes mappings in terms of
absolute physical address offsets. Once existing mmap users are
invalidated they can attempt to re-establish the mapping, or attempt to
continue issuing read(2) / write(2) to the invalidated extent, but they
will then be subject to the CONFIG_IO_STRICT_DEVMEM checking that can
block those subsequent accesses.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 90a545e9 ("restrict /dev/mem to idle io memory ranges")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/159009507306.847224.8502634072429766747.stgit@dwillia2-desk3.amr.corp.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This code was using get_user_pages*(), in approximately a "Case 1"
scenario (Direct IO), using the categorization from [1]. That means
that it's time to convert the get_user_pages*() + put_page() calls to
pin_user_pages*() + unpin_user_pages() calls.

There is some helpful background in [2]: basically, this is a small
part of fixing a long-standing disconnect between pinning pages, and
file systems' use of those pages.

[1] Documentation/core-api/pin_user_pages.rst

[2] "Explicit pinning of user-space pages":
    https://lwn.net/Articles/807108/

Cc: Derek Kiernan <derek.kiernan@xilinx.com>
Cc: Dragan Cvetic <dragan.cvetic@xilinx.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Link: https://lore.kernel.org/r/20200527012628.1100649-4-jhubbard@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Return 0 for success, rather than the value of an incrementing
"reg" index. The reg value was never actually used, so this
simplifies the caller slightly.

Cc: Derek Kiernan <derek.kiernan@xilinx.com>
Cc: Dragan Cvetic <dragan.cvetic@xilinx.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Link: https://lore.kernel.org/r/20200527012628.1100649-3-jhubbard@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes the case of get_user_pages_fast() returning a -errno.
The result needs to be stored in a signed integer. And for safe
signed/unsigned comparisons, it's best to keep everything signed.
And get_user_pages_fast() also expects a signed value for number
of pages to pin.

Therefore, change most relevant variables, from u32 to int. Leave
"n" unsigned, for convenience in checking for overflow. And provide
a WARN_ON_ONCE() and early return, if overflow occurs.

Also, as long as we're tidying up: rename the page array from page,
to pages, in order to match the conventions used in most other call
sites.

Fixes: 20ec628e ("misc: xilinx_sdfec: Add ability to configure LDPC")
Cc: Derek Kiernan <derek.kiernan@xilinx.com>
Cc: Dragan Cvetic <dragan.cvetic@xilinx.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Link: https://lore.kernel.org/r/20200527012628.1100649-2-jhubbard@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qfprom has different address spaces for read and write. Reads are
always done from corrected address space, where as writes are done
on raw address space.
Writing to corrected address space is invalid and ignored, so it
does not make sense to have this support in the driver which only
supports corrected address space regions at the moment.

Fixes: 4ab11996 ("nvmem: qfprom: Add Qualcomm QFPROM support.")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200522113341.7728-1-srinivas.kandagatla@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'misc-habanalabs-next-2020-05-25' of git://people.freedesktop.org/~gabbayo/linux into char-misc-next

Oded writes:

This tag contains the following changes for kernel 5.8:

- Improve MMU cache invalidation code and handle case where the
  invalidation doesn't finish in a reasonable time.

- Remove the option to perform soft-reset to GAUDI. Soft-reset is where the
  driver only resets the compute and DMA engines of the ASIC. This is not
  relevant to GAUDI as we must also reset the NIC ports. And when we reset
  the NIC ports, we must also reset other stuff so we prefer to just do
  hard-reset (where we reset the entire ASIC except for PCIe).

- Fail the hard-reset procedure in case we still have user processes which
  have active file-descriptors on a device. Doing hard-reset in that case
  can result in a kernel panic because of gen_pool checks

- Don't initialize the default wait callback of dma_buf with the default
  wait function as that's the default...

* tag 'misc-habanalabs-next-2020-05-25' of git://people.freedesktop.org/~gabbayo/linux:
  habanalabs: handle MMU cache invalidation timeout
  habanalabs: don't allow hard reset with open processes
  habanalabs: GAUDI does not support soft-reset
  habanalabs: add print for soft reset due to event
  habanalabs: improve MMU cache invalidation code
  habanalabs: don't set default fence_ops->wait

MMU cache invalidation timeout indicates that the device is unstable and
therefore unusable.
Hence in such case do hard reset and return an error to the user if was
called from ioctl.
In addition, change the print to error level and rephrase its text.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

When the MMU is heavily used by the engines, unmapping might take a lot of
time due to a full MMU cache invalidation done as part of the unmap flow.
Hence we might not be able to kill all open processes before going to hard
reset the device, as it involves unmapping of all user memory.
In case of a failure in killing all open processes, we should stop the
hard reset flow as it might lead to a kernel crash - one thread (killing
of a process) is updating MMU structures that other thread (hard reset) is
freeing.
Stopping a hard reset flow leaves the device as nonoperational and the
user can then initiate a hard reset via sysfs to reinitialize the device.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

GAUDI does not support soft-reset as it leaves the NIC ports in an awkward
state, where their QMANs were reset but the NIC itself is still working.

In addition, there is not much sense in doing soft-reset when training is
done on multiple GAUDIs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>

Print the event name that caused the soft reset.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

A new sequence is introduced to invalidate the MMU cache in order to avoid
timeouts.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

It's the default.

Also so much for "we're not going to tell the graphics people how to
review their code", dma_fence is a pretty core piece of gpu driver
infrastructure. And it's very much uapi relevant, including piles of
corresponding userspace protocols and libraries for how to pass these
around.

Would be great if habanalabs would not use this (from a quick look
it's not needed at all), since open source the userspace and playing
by the usual rules isn't on the table. If that's not possible (because
it's actually using the uapi part of dma_fence to interact with gpu
drivers) then we have exactly what everyone promised we'd want to
avoid.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

rts5249_set_aspm() and rts5260_set_aspm() do nothing more than the default
rtsx_comm_set_aspm() does, so remove them and use the default.  No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-7-helgaas@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify rtsx_comm_set_aspm() and remove the now-unused
rtsx_pci_enable_aspm().

rtsx_pci_disable_aspm() is still used by rtsx_pci_init_hw().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-6-helgaas@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of using the driver-specific rtsx_pci_update_cfg_byte() to update
the PCIe Link Control Register, use pcie_capability_clear_and_set_word()
like the rest of the kernel does.  This makes it easier to maintain ASPM
across the PCI core and drivers.

Remove the now-unused rtsx_pci_update_cfg_byte() and ASPM_MASK_NEG
definitions.

No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-5-helgaas@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use ASPM_MASK_NEG instead of hard-coded value, as other callers of
rtsx_pci_update_cfg_byte() do.  No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-4-helgaas@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The struct rtsx_cr_option.dev_aspm_mode member is never set to anything
other than DEV_ASPM_DYNAMIC (0).  Remove it and code that tests it.  No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-3-helgaas@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the following unused function pointers from struct pcr_ops:

  int (*set_ltr_latency)(struct rtsx_pcr *pcr, u32 latency);
  int (*set_l1off_sub)(struct rtsx_pcr *pcr, u8 val);
  void (*full_on)(struct rtsx_pcr *pcr);
  void (*power_saving)(struct rtsx_pcr *pcr);
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200521180545.1159896-2-helgaas@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The MHI device may be in the syserr state when we attempt to init it in
power_up().  Since we have no local state, the handling is simple -
reset the device and wait for it to transition out of the reset state.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-15-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Take write lock only to protect db_mode member of mhi channel.
This allows rest of the mhi channels to just take read lock which
fine grains the locking. It prevents channel readers to starve if
they try to enter critical section after a writer.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-14-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Devices that support RDDM do not require processing SYS_ERROR as it is
deemed redundant. Avoid SYS_ERROR processing if RDDM is supported by
the device.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-13-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Driver continues handling of BHI interrupt even if MHI register access
is not allowed. By doing so it calls the status call back and performs
early notification for the MHI client. This is not needed when MHI
register access is not allowed. Hence skip the handling in this case and
return. Also add debug log to print device state, local EE and device EE
when reg access is valid.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-12-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Mission mode transition is handled by state worker thread but
power off is not. There is a possibility while mission mode
transition is in progress which calls MHI client driver probe,
power off is issued by MHI controller. This results into client
driver probe and remove running in parallel and causes use after
free situation. By queuing disable transition work when mission
mode is in progress prevents the race condition.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-11-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the system error worker thread and instead have the
execution environment worker handle that transition to serialize
processing and avoid any possible race conditions during
shutdown.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-10-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

While writing any sequence or session identifiers, it is possible that
the host could write a zero value, whereas only non-zero values should
be supported writes to those registers. Ensure that the host does not
write a non-zero value for them and also log them in debug messages. A
macro is introduced to simplify this check and the existing checks are
also converted to use this macro.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-9-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add log messages to track boot flow errors and timeouts in SBL or AMSS
firmware loading to aid in debug.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-8-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When loading AMSS firmware using BHIe protocol, return -ETIMEDOUT if no
response is received within the timeout or return -EIO in case of a
protocol returned failure or an MHI error state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-7-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Upon power up, driver queues firmware worker thread if the execution
environment is PBL. Firmware worker is blocked with a timeout until
state worker gets a chance to run and unblock firmware worker. An
endpoint power up failure can be seen if state worker gets a chance to
run after firmware worker has timed out. Remove this dependency and
handle firmware load directly using state worker thread.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-6-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When MHI Driver receives an EOT event, it reads xfer_len from the
event in the last TRE. The value is under control of the MHI device
and never validated by Host MHI driver. The value should never be
larger than the real size of the buffer but a malicious device can
set the value 0xFFFF as maximum. This causes driver to memory
overflow (both read or write). Fix this issue by reading minimum of
transfer length from event and the buffer length provided.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-5-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MHI data completion handler function reads channel id from event
ring element. Value is under the control of MHI devices and can be
any value between 0 and 255. In order to prevent out of bound access
add a bound check against the max channel supported by controller
and skip processing of that event ring element.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-4-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Driver is using zero initialized intmod value from mhi channel when
configuring TRE for bei field. This prevents interrupt moderation to
take effect in case it is supported by an event ring. Fix this by
copying intmod value from associated event ring to mhi channel upon
registering mhi controller.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-3-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move all the common code to generate TRE from mhi_queue_buf,
mhi_queue_dma and mhi_queue_skb to mhi_gen_tre. This helps
to centralize the TRE generation code which makes any future
bug fixing easier to manage in these APIs.
Suggested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-2-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'soundwire-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next

Vinod writes:

soundwire updates for v5.8-rc1

This contains sdw_master_device patches and other updates done by Intel
folks.

Details:
  - sdw_master_device to represent the master instances.
  - sysfs properties for sdw_master_device and sdw_slave.
  - Documentation update for TDM modes.
  - some code cleanup patches and odd updates.

* tag 'soundwire-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
  soundwire: intel: use a single module
  soundwire: fix spelling mistake
  soundwire: fix trailing line in sysfs_slave.c
  soundwire: add Slave sysfs support
  soundwire: master: add sysfs support
  soundwire: disco: s/ch/channels/
  soundwire: master: add runtime pm support
  soundwire: bus_type: add sdw_master_device support
  soundwire: bus: add unique bus id
  soundwire: bus_type: introduce sdw_slave_type and sdw_master_type
  soundwire: bus: rename sdw_bus_master_add/delete, add arguments
  soundwire: intel: (cosmetic) remove multiple superfluous "else" statements
  soundwire: (cosmetic) remove multiple superfluous "else" statements
  soundwire: qcom: Use IRQF_ONESHOT
  soundwire: bus: reduce verbosity on enumeration
  soundwire: debugfs: clarify SDPX license with GPL-2.0-only
  soundwire: slave: don't init debugfs on device registration error
  Documentation: SoundWire: clarify TDM mode support
  soundwire: qcom: fix error handling in probe
  soundwire: intel: use asoc_rtd_to_cpu() / asoc_rtd_to_codec() macro for DAI pointer

Georgi writes:

interconnect changes for 5.8

These are the interconnect changes for the 5.8-rc1 merge window:

Core changes:
- Convert the framework core from tristate to bool to make handling
dependencies between other core frameworks easier
- Add of_icc_get_by_index()
- Add devm_of_icc_get() helper function
- Add icc_enable() and icc_disable() helpers

New drivers:
- Platform driver for NXP i.MX8MM SoC
- Platform driver for NXP i.MX8MN SoC
- Platform driver for NXP i.MX8MQ SoC
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>

* tag 'icc-5.8-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
  interconnect: Remove unused module exit code from core
  interconnect: Disallow interconnect core to be built as a module
  interconnect: Add of_icc_get_by_index() helper function
  interconnect: Add helpers for enabling/disabling a path
  interconnect: imx: Fix return value check in imx_icc_node_init_qos()
  interconnect: imx: Add platform driver for imx8mn
  interconnect: imx: Add platform driver for imx8mq
  interconnect: imx: Add platform driver for imx8mm
  interconnect: Add imx core driver
  dt-bindings: interconnect: Add bindings for imx8m noc
  interconnect: Add devm_of_icc_get() as exported API for users

The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200519154553.873413-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The problem is that we change "p_args" to point to the middle of the
string so when we free it at the end of the function it's not freeing
the same pointer that we originally allocated.

Fixes: e2c94d6f ("w1_therm: adding alarm sysfs entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200520120019.GA172354@mwandaSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's not clear why we have two modules for the Intel controller/master
support when there is a single Kconfig. This adds complexity for no
good reason, the two parts need to work together anyways.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200519191903.6557-1-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Fix typo for paranoia spelled as paranioa

Fixes: bcac5902 ("soundwire: add Slave sysfs support")
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Commit bcac5902 ("soundwire: add Slave sysfs support") added
trailing line in file sysfs_slave.c, so remove it

Fixes: bcac5902 ("soundwire: add Slave sysfs support")
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Expose MIPI DisCo Slave properties in sysfs.

For Slave properties and Data Port 0, the attributes are managed with
simple devm_ support.

A Slave Device may have more than one Data Port (DPN), and each Data
Port can be sink or source. The attributes are created dynamically
using pre-canned macros, but still use devm_ with a name attribute
group to avoid creating kobjects - as requested by GregKH. In the
_show function, we use container_of() to retrieve port number and
direction required to extract the information.

Audio modes are not supported for now. Depending on the discussions
the SoundWire Device Class, we may add it later as is or follow the
new specification.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200518203551.2053-4-yung-chuan.liao@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>