One timer, whose handler keeps reading on MMIO register for EEH
core to detect error in time, is started when the PCI device driver
is loaded. MMIO register can't be accessed during PE reset in EEH
recovery. Otherwise, the unexpected recursive error is triggered.
The timer isn't closed that time if the interface isn't brought
up. So the unexpected recursive error is seen during EEH recovery
when the interface is down.

This avoids the unexpected recursive EEH error by closing the timer
in qlge_io_error_detected() before EEH PE reset unconditionally. The
timer is started unconditionally after EEH PE reset in qlge_io_resume().
Also, the timer should be closed unconditionally when the device is
removed from the system permanently in qlge_io_error_detected().
Reported-by: Shriya R. Kulkarni <shriyakul@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.

If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>

"priority" needs to be signed for the error handling to work.

Fixes: 39651abd ('qed: add support for dcbx.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow-up to commit e27f4a94 ("bpf: Use mount_nodev not mount_ns
to mount the bpf filesystem"), which removes the FS_USERNS_MOUNT flag.

The original idea was to have a per mountns instance instead of a
single global fs instance, but that didn't work out and we had to
switch to mount_nodev() model. The intent of that middle ground was
that we avoid users who don't play nice to create endless instances
of bpf fs which are difficult to control and discover from an admin
point of view, but at the same time it would have allowed us to be
more flexible with regard to namespaces.

Therefore, since we now did the switch to mount_nodev() as a fix
where individual instances are created, we also need to remove userns
mount flag along with it to avoid running into mentioned situation.
I don't expect any breakage at this early point in time with removing
the flag and we can revisit this later should the requirement for
this come up with future users. This and commit e27f4a94 have
been split to facilitate tracking should any of them run into the
unlikely case of causing a regression.

Fixes: b2197755 ("bpf: add support for persistent maps/progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit fa50d974 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
moves the default TTL assignment, and as side-effect IPv4 TTL now
has a default value only if sysctl support is enabled (CONFIG_SYSCTL=y).

The sysctl_ip_default_ttl is fundamental for IP to work properly,
as it provides the TTL to be used as default. The defautl TTL may be
used in ip_selected_ttl, through the following flow:

  ip_select_ttl
    ip4_dst_hoplimit
      net->ipv4.sysctl_ip_default_ttl

This commit fixes the issue by assigning net->ipv4.sysctl_ip_default_ttl
in net_init_net, called during ipv4's initialization.

Without this commit, a kernel built without sysctl support will send
all IP packets with zero TTL (unless a TTL is explicitly set, e.g.
with setsockopt).

Given a similar issue might appear on the other knobs that were
namespaceify, this commit also moves them.

Fixes: fa50d974 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use memdup_user to duplicate a memory region from user-space to
kernel-space, instead of open coding using kmalloc & copy_from_user.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the statement
  assert(priv || priv->ae_handle);
the right side of || is only evaluated if priv is null.

v2:
	As suggested by David Leight and David Miller the assert
	statements are removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sk_err and sk_err_soft fields are positive errno values and
userspace applications rely on this when using getsockopt(SO_ERROR).

ATM code places an -errno into sk_err_soft in sigd_send() and returns it
from svc_addparty()/svc_dropparty().

Although I am not familiar with ATM code I came to this conclusion
because:

1. sigd_send() msg->type cases as_okay and as_error both have:

   sk->sk_err = -msg->reply;

   while the as_addparty and as_dropparty cases have:

   sk->sk_err_soft = msg->reply;

   This is the source of the inconsistency.

2. svc_addparty() returns an -errno and assumes sk_err_soft is also an
   -errno:

       if (flags & O_NONBLOCK) {
           error = -EINPROGRESS;
           goto out;
       }
       ...
       error = xchg(&sk->sk_err_soft, 0);
   out:
       release_sock(sk);
       return error;

   This shows that sk_err_soft is indeed being treated as an -errno.

This patch ensures that sk_err_soft is always a positive errno.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If !count is true, count < 4 is also true.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull motr tracing updates from Steven Rostedt:
 "Three more changes.

   - I forgot that I had another selftest to stress test the ftrace
     instance creation.  It was actually suppose to go into the 4.6
     merge window, but I never committed it.  I almost forgot about it
     again, but noticed it was missing from your tree.

   - Soumya PN sent me a clean up patch to not disable interrupts when
     taking the tasklist_lock for read, as it's unnecessary because that
     lock is never taken for write in irq context.

   - Newer gcc's can cause the jump in the function_graph code to the
     global ftrace_stub label to be a short jump instead of a long one.
     As that jump is dynamically converted to jump to the trace code to
     do function graph tracing, and that conversion expects a long jump
     it can corrupt the ftrace_stub itself (it's directly after that
     call).  One way to prevent gcc from using a short jump is to
     declare the ftrace_stub as a weak function, which we do here to
     keep gcc from optimizing too much"

* tag 'trace-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace/x86: Set ftrace_stub to weak to prevent gcc from using short jumps to it
  ftrace: Don't disable irqs when taking the tasklist_lock read_lock
  ftracetest: Add instance created, delete, read and enable event test

Pull m68knommu update from Greg Ungerer:
 "Only a single change to update my email address in the MAINTAINERS
  file"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: change m68knommu maintainer email address

Pull sparc updates from David Miller:
 "Some 32-bit kgdb cleanups from Sam Ravnborg, and a hugepage TLB flush
  overhead fix on 64-bit from Nitin Gupta"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Reduce TLB flushes during hugepte changes
  aeroflex/greth: fix warning about unused variable
  openprom: fix warning
  sparc32: drop superfluous cast in calls to __nocache_pa()
  sparc32: fix build with STRICT_MM_TYPECHECKS
  sparc32: use proper prototype for trapbase
  sparc32: drop local prototype in kgdb_32
  sparc32: drop hardcoding trap_level in kgdb_trap

I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.

For example, the 32-bit version of "__copy_from_user_inatomic()" is
mostly the special cases for the constant size, and it's actually almost
never relevant.  Most users aren't actually using a constant size
anyway, and the few cases that do small constant copies are better off
just using __get_user() instead.

So get rid of the unnecessary complexity.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.

For example, the 32-bit version of "__copy_to_user_inatomic()" is mostly
the special cases for the constant size, and it's actually never
relevant.  Every user except for one aren't actually using a constant
size anyway, and the one user that uses it is better off just using
__put_user() instead.

So get rid of the unnecessary complexity.

[ The same cleanup should likely happen to __copy_from_user_inatomic()
  as well, but that one has a lot more users that I need to take a look
  at first ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull f2fs updates from Jaegeuk Kim:
 "In this round, as Ted pointed out, fscrypto allows one more key prefix
  given by filesystem to resolve backward compatibility issues.  Other
  than that, we've fixed several error handling cases by introducing
  a fault injection facility.  We've also achieved performance
  improvement in some workloads as well as a bunch of bug fixes.

  Summary:

  Enhancements:
   - fs-specific prefix for fscrypto
   - fault injection facility
   - expose validity bitmaps for user to be aware of fragmentation
   - fallocate/rm/preallocation speed up
   - use percpu counters

  Bug fixes:
   - some inline_dentry/inline_data bugs
   - error handling for atomic/volatile/orphan inodes
   - recover broken superblock"

* tag 'for-f2fs-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (73 commits)
  f2fs: fix to update dirty page count correctly
  f2fs: flush pending bios right away when error occurs
  f2fs: avoid ENOSPC fault in the recovery process
  f2fs: make exit_f2fs_fs more clear
  f2fs: use percpu_counter for total_valid_inode_count
  f2fs: use percpu_counter for alloc_valid_block_count
  f2fs: use percpu_counter for # of dirty pages in inode
  f2fs: use percpu_counter for page counters
  f2fs: use bio count instead of F2FS_WRITEBACK page count
  f2fs: manipulate dirty file inodes when DATA_FLUSH is set
  f2fs: add fault injection to sysfs
  f2fs: no need inc dirty pages under inode lock
  f2fs: fix incorrect error path handling in f2fs_move_rehashed_dirents
  f2fs: fix i_current_depth during inline dentry conversion
  f2fs: correct return value type of f2fs_fill_super
  f2fs: fix deadlock when flush inline data
  f2fs: avoid f2fs_bug_on during recovery
  f2fs: show # of orphan inodes
  f2fs: support in batch fzero in dnode page
  f2fs: support in batch multi blocks preallocation
  ...

Pull btrfs updates from Chris Mason:
 "This has our merge window series of cleanups and fixes.  These target
  a wide range of issues, but do include some important fixes for
  qgroups, O_DIRECT, and fsync handling.  Jeff Mahoney moved around a
  few definitions to make them easier for userland to consume.

  Also whiteout support is included now that issues with overlayfs have
  been cleared up.

  I have one more fix pending for page faults during btrfs_copy_from_user,
  but I wanted to get this bulk out the door first"

* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (90 commits)
  btrfs: fix memory leak during RAID 5/6 device replacement
  Btrfs: add semaphore to synchronize direct IO writes with fsync
  Btrfs: fix race between block group relocation and nocow writes
  Btrfs: fix race between fsync and direct IO writes for prealloc extents
  Btrfs: fix number of transaction units for renames with whiteout
  Btrfs: pin logs earlier when doing a rename exchange operation
  Btrfs: unpin logs if rename exchange operation fails
  Btrfs: fix inode leak on failure to setup whiteout inode in rename
  btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT
  Btrfs: pin log earlier when renaming
  Btrfs: unpin log if rename operation fails
  Btrfs: don't do unnecessary delalloc flushes when relocating
  Btrfs: don't wait for unrelated IO to finish before relocation
  Btrfs: fix empty symlink after creating symlink and fsync parent dir
  Btrfs: fix for incorrect directory entries after fsync log replay
  btrfs: build fixup for qgroup_account_snapshot
  btrfs: qgroup: Fix qgroup accounting when creating snapshot
  Btrfs: fix fspath error deallocation
  btrfs: make find_workspace warn if there are no workspaces
  btrfs: make find_workspace always succeed
  ...

Pull RTC updates from Alexandre Belloni:
 "Subsystem wide cleanups:
   - Use IS_ENABLED() instead of checking for built-in or module
   - remove useless DRV_VERSION
   - remove CLK_IS_ROOT
   - remove UIE signaling

  Drivers:
   - ds1302: rewritten to be a proper SPI device driver
   - m41t80: huge cleanup, alarm, wakelarm ans oscialltor failure
     detection support
   - rv3029: switch to regmap to handle rv3049, alarm support, fixes
   - zynqmp: enable switching to battery power, fixes
   - small fixes for at91sam9, da9053, ds1307, ds1685, ds3232, r2025,
     sa1100, snvs, stmp3xxx, tps6586x"

* tag 'rtc-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (40 commits)
  rtc: tps6586x: rename so module can be autoloaded
  rtc: rv3029: hide unused i2c device table
  rtc: rs5c372: r2025: fix check for 'oscillator halted' condition
  rtc: rv3029: add alarm IRQ
  rtc: rv3029: fix set_time function
  rtc: rv3029: fix alarm support
  rtc: rv3029: Remove some checks and warnings
  rtc: rv3029: Add support of RV3049
  rtc: rv3029: convert to use regmap
  rtc: rv3029: remove 'i2c' in functions names
  rtc: stmp3xxx: print message on error
  rtc: Use IS_ENABLED() instead of checking for built-in or module
  rtc: ds3232: fix call trace when rtc->ops_lock is used as NULL
  rtc: snvs: return error in case enable_irq_wake fails
  rtc: zynqmp: Update seconds time programming logic
  rtc: sa1100: DT spelling s/interrupt-name/interrupt-names/
  rtc: mc13xxx: remove UIE signaling
  rtc: mxc: remove UIE signaling
  rtc: ds1307: Remove CLK_IS_ROOT
  rtc: hym8563: Remove CLK_IS_ROOT
  ...

Pull mailbox updates from Jassi Brar:
 "OMAP:
   - Remove non-DT support from mailbox driver
   - Move PM from client calls to native driver suspend/resume
   - Trivial cleanups to make checkpatch happy

  STI:
   - Check return from devm_ioremap_resource as ERR_PTR, not NULL"

* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: Fix devm_ioremap_resource error detection code
  mailbox/omap: kill omap_mbox_{save/restore}_ctx() functions
  mailbox/omap: check for any unread messages during suspend
  mailbox/omap: add support for suspend/resume
  mailbox/omap: store mailbox interrupt type in omap_mbox_device
  mailbox/omap: add blank lines after declarations
  mailbox/omap: remove FSF mailing address paragraph
  mailbox/omap: use variable name for sizeof() operator
  mailbox/omap: drop legacy platform device support

Commit b3c1be1b ("base: isa: Remove X86_32 dependency") made ISA
support available on x86-64 too.  That's not right - while there are
some LPC-style devices that might be useful still and be based on
ISA-like IP blocks, that is *not* an excuse to try to enable any random
legacy drivers.

Such drivers should be individually enabled and made to perhaps depend
on ISA_DMA_API instead (which we have continued to support on x86-64).
Or we could add another "ISA_XYZ_API" that we support that doesn't
enable random old drivers that aren't even 64-bit clean nor do we have
any test coverage for.

Turning off ISA will now also turn off some drivers that have been
marked as depending on it as part of this series, and that used to work
on modern platforms.

See for example commits ad7afc38..cc736607, which may also need
to be reverted.

This commit means that the warnings that came in due to enabling ISA
widely are now gone again.
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This module is loaded by the related mfd driver which has
the needed MODULE_DEVICE_TABLE(i2c,...).

This patch fix the modalias when the rtc driver is built
as a module, so the right name is used.
Everything operates correctly when this module is builtin.

Fixes: esdc59ed38 ("rtc: add RTC driver for TPS6586x")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The added support for SPI mode made it possible to configure the driver
when I2C is disabled, leaving an unused device table:

drivers/rtc/rtc-rv3029c2.c:794:29: error: 'rv3029_id' defined but not used [-Werror=unused-variable]

This moves the table inside of the #ifdef section that has the
only user, to avoid the harmless warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d08f50dd0afc ("rtc: rv3029: Add support of RV3049")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The R2025SD chip, according to its data sheet, sets the /XST
bit to zero if the oscillator stops. Hence the check for this
condition was wrong.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add the alarm IRQ functionality.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The bin2bcd function in set_time is uncorrect on weekdays as the
bit mask should be done at the end of arithmetic operations.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC RV3029 handles different types of alarms : seconds, minutes, ...
These alarms can be enabled or disabled individually using an AE_x bit
which is the last bit (BIT(7)) on each alarm registers.

To prepare the alarm IRQ support, the current code enables all the alarm
types by setting each AE_x to 1.
It also fixes others alarms issues :
   - month and weekday errors : it was performing -1 instead of +1.
   - wrong use of bit mask with bin2bcd
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Remove some checks from checkpatch such as spaces around arithmetic
operations or prefer "unsigned int".
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add support of Microcrystal RV3049 RTC (SPI) using regmap on the
RV3029 (I2C) driver.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

To add support of rv3049, the current driver is converted to use regmap.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

To prepare the use of regmap to add the support of RV-3049, all the
'i2c' in functions's names are removed.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Merge more updates from Andrew Morton:

 - the rest of MM

 - KASAN updates

 - procfs updates

 - exit, fork updates

 - printk updates

 - lib/ updates

 - radix-tree testsuite updates

 - checkpatch updates

 - kprobes updates

 - a few other misc bits

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
  samples/kprobes: print out the symbol name for the hooks
  samples/kprobes: add a new module parameter
  kprobes: add the "tls" argument for j_do_fork
  init/main.c: simplify initcall_blacklisted()
  fs/efs/super.c: fix return value
  checkpatch: improve --git <commit-count> shortcut
  checkpatch: reduce number of `git log` calls with --git
  checkpatch: add support to check already applied git commits
  checkpatch: add --list-types to show message types to show or ignore
  checkpatch: advertise the --fix and --fix-inplace options more
  checkpatch: whine about ACCESS_ONCE
  checkpatch: add test for keywords not starting on tabstops
  checkpatch: improve CONSTANT_COMPARISON test for structure members
  checkpatch: add PREFER_IS_ENABLED test
  lib/GCD.c: use binary GCD algorithm instead of Euclidean
  radix-tree: free up the bottom bit of exceptional entries for reuse
  dax: move RADIX_DAX_ definitions to dax.c
  radix-tree: make radix_tree_descend() more useful
  radix-tree: introduce radix_tree_replace_clear_tags()
  radix-tree: tidy up __radix_tree_create()
  ...

Pull staging and IIO driver updates from Greg KH:
 "Here's the big staging and iio driver update for 4.7-rc1.

  I think we almost broke even with this release, only adding a few more
  lines than we removed, which isn't bad overall given that there's a
  bunch of new iio drivers added.

  The Lustre developers seem to have woken up from their sleep and have
  been doing a great job in cleaning up the code and pruning unused or
  old cruft, the filesystem is almost readable :)

  Other than that, just a lot of basic coding style cleanups in the
  churn.  All have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (938 commits)
  Staging: emxx_udc: emxx_udc: fixed coding style issue
  staging/gdm724x: fix "alignment should match open parenthesis" issues
  staging/gdm724x: Fix avoid CamelCase
  staging: unisys: rename misleading var ii with frag
  staging: unisys: visorhba: switch success handling to error handling
  staging: unisys: visorhba: main path needs to flow down the left margin
  staging: unisys: visorinput: handle_locking_key() simplifications
  staging: unisys: visorhba: fail gracefully for thread creation failures
  staging: unisys: visornic: comment restructuring and removing bad diction
  staging: unisys: fix format string %Lx to %llx for u64
  staging: unisys: remove unused struct members
  staging: unisys: visorchannel: correct variable misspelling
  staging: unisys: visorhba: replace functionlike macro with function
  staging: dgnc: Need to check for NULL of ch
  staging: dgnc: remove redundant condition check
  staging: dgnc: fix 'line over 80 characters'
  staging: dgnc: clean up the dgnc_get_modem_info()
  staging: lustre: lnet: enable configuration per NI interface
  staging: lustre: o2iblnd: properly set ibr_why
  staging: lustre: o2iblnd: remove last of kiblnd_tunables_fini
  ...

Pull driver core updates from Greg KH:
 "Here's the "big" driver core update for 4.7-rc1.

  Mostly just debugfs changes, the long-known and messy races with
  removing debugfs files should be fixed thanks to the great work of
  Nicolai Stange.  We also have some isa updates in here (the x86
  maintainers told me to take it through this tree), a new warning when
  we run out of dynamic char major numbers, and a few other assorted
  changes, details in the shortlog.

  All have been in linux-next for some time with no reported issues"

* tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
  Revert "base: dd: don't remove driver_data in -EPROBE_DEFER case"
  gpio: ws16c48: Utilize the ISA bus driver
  gpio: 104-idio-16: Utilize the ISA bus driver
  gpio: 104-idi-48: Utilize the ISA bus driver
  gpio: 104-dio-48e: Utilize the ISA bus driver
  watchdog: ebc-c384_wdt: Utilize the ISA bus driver
  iio: stx104: Utilize the module_isa_driver and max_num_isa_dev macros
  iio: stx104: Add X86 dependency to STX104 Kconfig option
  Documentation: Add ISA bus driver documentation
  isa: Implement the max_num_isa_dev macro
  isa: Implement the module_isa_driver macro
  pnp: pnpbios: Add explicit X86_32 dependency to PNPBIOS
  isa: Decouple X86_32 dependency from the ISA Kconfig option
  driver-core: use 'dev' argument in dev_dbg_ratelimited stub
  base: dd: don't remove driver_data in -EPROBE_DEFER case
  kernfs: Move faulting copy_user operations outside of the mutex
  devcoredump: add scatterlist support
  debugfs: unproxify files created through debugfs_create_u32_array()
  debugfs: unproxify files created through debugfs_create_blob()
  debugfs: unproxify files created through debugfs_create_bool()
  ...

Pull char / misc driver updates from Greg KH:
 "Here's the big char and misc driver update for 4.7-rc1.

  Lots of different tiny driver subsystems have updates here with new
  drivers and functionality.  Details in the shortlog.

  All have been in linux-next with no reported issues for a while"

* tag 'char-misc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (125 commits)
  mcb: Delete num_cells variable which is not required
  mcb: Fixed bar number assignment for the gdd
  mcb: Replace ioremap and request_region with the devm version
  mcb: Implement bus->dev.release callback
  mcb: export bus information via sysfs
  mcb: Correctly initialize the bus's device
  mei: bus: call mei_cl_read_start under device lock
  coresight: etb10: adjust read pointer only when needed
  coresight: configuring ETF in FIFO mode when acting as link
  coresight: tmc: implementing TMC-ETF AUX space API
  coresight: moving struct cs_buffers to header file
  coresight: tmc: keep track of memory width
  coresight: tmc: make sysFS and Perf mode mutually exclusive
  coresight: tmc: dump system memory content only when needed
  coresight: tmc: adding mode of operation for link/sinks
  coresight: tmc: getting rid of multiple read access
  coresight: tmc: allocating memory when needed
  coresight: tmc: making prepare/unprepare functions generic
  coresight: tmc: splitting driver in ETB/ETF and ETR components
  coresight: tmc: cleaning up header file
  ...

Pull USB updates from Greg KH:
 "Here's the big pull request for USB and PHY drivers for 4.7-rc1

  Full details in the shortlog, but it's the normal major gadget driver
  updates, phy updates, new usbip code, as well as a bit of lots of
  other stuff.

  All have been in linux-next with no reported issues"

* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
  USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
  USB: serial: fix minor-number allocation
  USB: serial: quatech2: fix use-after-free in probe error path
  USB: serial: mxuport: fix use-after-free in probe error path
  USB: serial: keyspan: fix debug and error messages
  USB: serial: keyspan: fix URB unlink
  USB: serial: keyspan: fix use-after-free in probe error path
  USB: serial: io_edgeport: fix memory leaks in probe error path
  USB: serial: io_edgeport: fix memory leaks in attach error path
  usb: Remove unnecessary space before operator ','.
  usb: Remove unnecessary space before open square bracket.
  USB: FHCI: avoid redundant condition
  usb: host: xhci-rcar: Avoid long wait in xhci_reset()
  usb/host/fotg210: remove dead code in create_sysfs_files
  usb: wusbcore: Do not initialise statics to 0.
  usb: wusbcore: Remove space before ',' and '(' .
  USB: serial: cp210x: clean up CRTSCTS flag code
  USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
  USB: serial: cp210x: fix hardware flow-control disable
  USB: serial: option: add even more ZTE device ids
  ...

Pull tty and serial driver updates from Greg KH:
 "Here's the large TTY and Serial driver update for 4.7-rc1.

  A few new serial drivers are added here, and Peter has fixed a bunch
  of long-standing bugs in the tty layer and serial drivers as normal.
  Full details in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
  MAINTAINERS: 8250: remove website reference
  serial: core: Fix port mutex assert if lockdep disabled
  serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
  tty: vt, finish looping on duplicate
  tty: vt, return error when con_startup fails
  QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
  serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
  serial: 8250dw: Add device HID for future AMD UART controller
  Fix OpenSSH pty regression on close
  serial: mctrl_gpio: add IRQ locking
  serial: 8250: Integrate Fintek into 8250_base
  serial: mps2-uart: add support for early console
  serial: mps2-uart: add MPS2 UART driver
  dt-bindings: document the MPS2 UART bindings
  serial: sirf: Use generic uart-has-rtscts DT property
  serial: sirf: Introduce helper variable struct device_node *np
  serial: mxs-auart: Use generic uart-has-rtscts DT property
  serial: imx: Use generic uart-has-rtscts DT property
  doc: DT: Add Generic Serial Device Tree Bindings
  serial: 8250: of: Make tegra_serial_handle_break() static
  ...

Pull clk updates from Stephen Boyd:
 "It's the usual big pile of driver updates and additions, but we do
  have a couple core changes in here as well.

  Core:

   - CLK_IS_CRITICAL support has been added.  This should allow drivers
     to properly express that a certain clk should stay on even if their
     prepare/enable count drops to 0 (and in turn the parents of these
     clks should stay enabled).

   - A clk registration API has been added, clk_hw_register(), and an OF
     clk provider API has been added, of_clk_add_hw_provider().  These
     APIs have been put in place to further split clk providers from clk
     consumers, with the goal being to have clk providers never deal
     with struct clk pointers at all.  Conversion of provider drivers is
     on going.  clkdev has also gained support for registering clk_hw
     pointers directly so we can convert drivers that don't use
     devicetree.

  New Drivers:

   - Marvell ap806 and cp110 system controllers (with clks inside!)
   - Hisilicon Hi3519 clock and reset controller
   - Axis ARTPEC-6 clock controllers
   - Oxford Semiconductor OXNAS clock controllers
   - AXS10X I2S PLL
   - Rockchip RK3399 clock and reset controller

  Updates:

   - MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos
     542x SoCs, and some more clk ID exporting for bus frequency scaling
   - Proper BCM2835 PCM clk support and various other clks
   - i.MX clk updates for i.MX6SX, i.MX7, and VF610
   - Renesas updates for R-Car H3
   - Tegra210 got updates for DisplayPort and HDMI 2.0
   - Rockchip driver refactorings and fixes due to adding RK3399 support"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (139 commits)
  clk: fix critical clock locking
  clk: qcom: mmcc-8996: Remove clocks that should be controlled by RPM
  clk: ingenic: Allow divider value to be divided
  clk: sunxi: Add display and TCON0 clocks driver
  clk: rockchip: drop old_rate calculation on pll rate changes
  clk: rockchip: simplify GRF handling in pll clocks
  clk: rockchip: lookup General Register Files in rockchip_clk_init
  clk: rockchip: fix the rk3399 sdmmc sample / drv name
  clk: mvebu: new driver for Armada CP110 system controller
  dt-bindings: arm: add DT binding for Marvell CP110 system controller
  clk: mvebu: new driver for Armada AP806 system controller
  clk: hisilicon: add CRG driver for hi3519 soc
  clk: hisilicon: export some hisilicon APIs to modules
  reset: hisilicon: add reset controller driver for hisilicon SOCs
  clk: bcm/kona: Do not use sizeof on pointer type
  clk: qcom: msm8916: Fix crypto clock flags
  clk: nxp: lpc18xx: Initialize clk_init_data::flags to 0
  clk/axs10x: Add I2S PLL clock driver
  clk: imx7d: fix ahb clock mux 1
  clk: fix comment of devm_clk_hw_register()
  ...

Pull networking fixes and more updates from David Miller:

 1) Tunneling fixes from Tom Herbert and Alexander Duyck.

 2) AF_UNIX updates some struct sock bit fields with the socket lock,
    whereas setsockopt() sets overlapping ones with locking.  Seperate
    out the synchronized vs.  the AF_UNIX unsynchronized ones to avoid
    corruption.  From Andrey Ryabinin.

 3) Mount BPF filesystem with mount_nodev rather than mount_ns, from
    Eric Biederman.

 4) A couple kmemdup conversions, from Muhammad Falak R Wani.

 5) BPF verifier fixes from Alexei Starovoitov.

 6) Don't let tunneled UDP packets get stuck in socket queues, if
    something goes wrong during the encapsulation just drop the packet
    rather than signalling an error up the call stack.  From Hannes
    Frederic Sowa.

 7) SKB ref after free in batman-adv, from Florian Westphal.

 8) TCP iSCSI, ocfs2, rds, and tipc have to disable BH in it's TCP
    callbacks since the TCP stack runs pre-emptibly now.  From Eric
    Dumazet.

 9) Fix crash in fixed_phy_add, from Rabin Vincent.

10) Fix length checks in xen-netback, from Paul Durrant.

11) Fix mixup in KEY vs KEYID macsec attributes, from Sabrina Dubroca.

12) RDS connection spamming bug fixes from Sowmini Varadhan

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
  net: suppress warnings on dev_alloc_skb
  uapi glibc compat: fix compilation when !__USE_MISC in glibc
  udp: prevent skbs lingering in tunnel socket queues
  bpf: teach verifier to recognize imm += ptr pattern
  bpf: support decreasing order in direct packet access
  net: usb: ch9200: use kmemdup
  ps3_gelic: use kmemdup
  net:liquidio: use kmemdup
  bpf: Use mount_nodev not mount_ns to mount the bpf filesystem
  net: cdc_ncm: update datagram size after changing mtu
  tuntap: correctly wake up process during uninit
  intel: Add support for IPv6 IP-in-IP offload
  ip6_gre: Do not allow segmentation offloads GRE_CSUM is enabled with FOU/GUE
  RDS: TCP: Avoid rds connection churn from rogue SYNs
  RDS: TCP: rds_tcp_accept_worker() must exit gracefully when terminating rds-tcp
  net: sock: move ->sk_shutdown out of bitfields.
  ipv6: Don't reset inner headers in ip6_tnl_xmit
  ip4ip6: Support for GSO/GRO
  ip6ip6: Support for GSO/GRO
  ipv6: Set features for IPv6 tunnels
  ...

Similar to commits:

  51d7d520 ("powerpc: Add smp_mb() to arch_spin_is_locked()")
  d86b8da0 ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")

qspinlock suffers from the fact that the _Q_LOCKED_VAL store is
unordered inside the ACQUIRE of the lock.

And while this is not a problem for the regular mutual exclusive
critical section usage of spinlocks, it breaks creative locking like:

	spin_lock(A)			spin_lock(B)
	spin_unlock_wait(B)		if (!spin_is_locked(A))
	do_something()			  do_something()

In that both CPUs can end up running do_something at the same time,
because our _Q_LOCKED_VAL store can drop past the spin_unlock_wait()
spin_is_locked() loads (even on x86!!).

To avoid making the normal case slower, add smp_mb()s to the less used
spin_unlock_wait() / spin_is_locked() side of things to avoid this
problem.
Reported-and-tested-by: Davidlohr Bueso <dave@stgolabs.net>
Reported-by: Giovanni Gherdovich <ggherdovich@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org   # v4.2 and later
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>