Pull hwmon fix from Guenter Roeck:
 "Fix chip initialization/configuration in MAX6697 driver"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (max6697) fix MAX6581 ideality

Pull arm fixes fixes from Russell King:
 "This fixes a couple of problems with commit 48be69a0 ("ARM: move
  signal handlers into a vdso-like page"), one of which was originally
  discovered via my testing originally, but the fix for it was never
  actually committed.

  The other shows up on noMMU builds, and such platforms are extremely
  rare and as such are not part of my nightly testing"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: fix nommu builds with 48be69a0 (ARM: move signal handlers into a vdso-like page)
  ARM: fix a cockup in 48be69a0 (ARM: move signal handlers into a vdso-like page)

Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Olof reports that noMMU builds error out with:

arch/arm/kernel/signal.c: In function 'setup_return':
arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage'

This shows one of the evilnesses of IS_ENABLED().  Get rid of it here
and replace it with #ifdef's - and as no noMMU platform can make use
of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Unfortunately, I never committed the fix to a nasty oops which can
occur as a result of that commit:

------------[ cut here ]------------
kernel BUG at /home/olof/work/batch/include/linux/mm.h:414!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 490 Comm: killall5 Not tainted 3.11.0-rc3-00288-gabe03080 #53
task: e90acac0 ti: e9be8000 task.ti: e9be8000
PC is at special_mapping_fault+0xa4/0xc4
LR is at __do_fault+0x68/0x48c

This doesn't show up unless you do quite a bit of testing; a simple
boot test does not do this, so all my nightly tests were passing fine.

The reason for this is that install_special_mapping() expects the
page array to stick around, and as this was only inserting one page
which was stored on the kernel stack, that's why this was blowing up.
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull infiniband/rdma fixes from Roland Dreier:
 - Fixes for the newly merged mlx5 hardware driver
 - Stack info leak fixes from Dan Carpenter
 - Fixes for pkey table handling with SR-IOV
 - A few other small things

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Fix pkey change flow for virtualization environments
  IPoIB: Make sure child devices use valid/proper pkeys
  IB/core: Create QP1 using the pkey index which contains the default pkey
  mlx5_core: Variable may be used uninitialized
  mlx5_core: Implement new initialization sequence
  mlx5_core: Fix use after free in mlx5_cmd_comp_handler()
  IB/mlx5: Fix stack info leak in mlx5_ib_alloc_ucontext()
  IB/mlx5: Fix error return code in init_one()
  IB/mlx4: Use default pkey when creating tunnel QPs
  RDMA/cma: Only call cma_save_ib_info() for CM REQs
  RDMA/cma: Fix accessing invalid private data for UD
  RDMA/cma: Fix gcc warning
  Revert "RDMA/nes: Fix compilation error when nes_debug is enabled"
  IB/qib: Add err_decode() call for ring dump
  RDMA/cxgb3: Fix stack info leak in iwch_create_cq()
  RDMA/nes: Fix info leaks in nes_create_qp() and nes_create_cq()
  RDMA/ocrdma: Fix several stack info leaks
  RDMA/cxgb4: Fix stack info leak in c4iw_create_qp()
  RDMA/ocrdma: Remove unused include

Pull GPIO fixes from Linus Walleij:
 "Yet another GPIO pull request, fixing the fix from the last one.  It
  turns out that fixing the boot path for device tree boots on OMAP
  breaks out antique systems (such as OMAP1) and we need to find a
  better way.  So we're reverting that "fix" for the moment and thinking
  about something better.

  Also fixing a build issue on the MSM driver"

* tag 'gpio-for-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio_msm: Fix build error due to missing err.h
  Revert "gpio/omap: don't create an IRQ mapping for every GPIO on DT"
  Revert "gpio/omap: auto request GPIO as input if used as IRQ via DT"
  Revert "gpio/omap: fix build error when OF_GPIO is not defined."

Pull powerpc fixes from Ben Herrenschmidt:
 "Here is not quite a handful of powerpc fixes for rc3.

  The windfarm fix is a regression fix (though not a new one), the PMU
  interrupt rename is not a fix per-se but has been submitted a long
  time ago and I kept forgetting to put it in (it puts us back in sync
  with x86), the other perf bit is just about putting an API/ABI bit
  definition in the right place for userspace to consume, and finally,
  we have a fix for the VPHN (Virtual Partition Home Node) feature
  (notification that the hypervisor is moving nodes around) which could
  cause lockups so we may as well fix it now"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/windfarm: Fix noisy slots-fan on Xserve (rm31)
  powerpc: VPHN topology change updates all siblings
  powerpc/perf: Export PERF_EVENT_CONFIG_EBB_SHIFT to userspace
  powerpc: Rename PMU interrupts from CNT to PMI

Pull ARM fixes from Russell King:
 "I've thought long and hard about what to say for this pull request,
  and I really can't work out anything sane to say to summarise much of
  these commits.  The problem is, for most of these are, yet again, lots
  of small bits scattered around the place without any real overall
  theme to them"

Most notable is probably the kuser page helper improvements.

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (22 commits)
  ARM: Add .text annotations where required after __CPUINIT removal
  ARM: 7803/1: Fix deadlock scenario with smp_send_stop()
  ARM: make vectors page inaccessible from userspace
  ARM: move signal handlers into a vdso-like page
  ARM: allow kuser helpers to be removed from the vector page
  ARM: update FIQ support for relocation of vectors
  ARM: use linker magic for vectors and vector stubs
  ARM: move vector stubs
  ARM: poison memory between kuser helpers
  ARM: poison the vectors page
  ARM: 7801/1: v6: prevent gcc 4.5 from reordering extended CP15 reads above is_smp() test
  ARM: 7800/1: ARMv7-M: Fix name of NVIC handler function
  ARM: Fix sorting of machine- initializers
  ARM: 7791/1: a.out: remove partial a.out support
  ARM: 7790/1: Fix deferred mm switch on VIVT processors
  ARM: 7789/1: Do not run dummy_flush_tlb_a15_erratum() on non-Cortex-A15
  ARM: 7787/1: virt: ensure visibility of __boot_cpu_mode
  ARM: 7788/1: elf: fix lpae hwcap feature reporting in proc/cpuinfo
  ARM: 7786/1: hyp: fix macro parameterisation
  ARM: 7785/1: mm: restrict early_alloc to section-aligned memory
  ...

Pull parisc updates from Helge Deller:
 "The majority of lines changed are due the addition of a defconfig for
  the C8000 machine.  Even the fix in parisc/kernel/cache.c file is
  actually ony a 10-line fix, but the change became bigger (and much
  nicer) to avoid errors of the checkpatch script.

  Here is the short-changelog:

  This round of parisc updates includes mostly fixes for the C8000
  workstation.  We have a new defconfig file for this machine, as well
  as fixes for it's serial port, the AGP driver and the cache routines
  to cope with the vmas of the FireGL card in a C8000.  The sys32.h
  header file was not used and as such it's now gone"

* 'parisc-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix interrupt routing for C8000 serial ports
  parisc: Remove arch/parisc/kernel/sys32.h header
  parisc: add defconfig for c8000 machine
  parisc: agp/parisc-agp: allow binding of user memory to the AGP GART
  parisc: Fix cache routines to ignore vma's with an invalid pfn

Pull HID fixes from Jiri Kosina:
 - fix hid-sony PS3 sixaxxis breakage from Benjamin Tissories
 - fix hidraw race condition from Yonghua Zheng
 - fix/bandaid for rare device enumeration problems of Logitech Unifying
   receivers from Nestor Lopez Casado

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hidraw: fix improper mutex release
  HID: sony: fix HID mapping for PS3 sixaxis controller
  HID: hid-logitech-dj: querying_devices was never set
  HID: Revert "Revert "HID: Fix logitech-dj: missing Unifying device issue""

Pull MCE fix from Tony Luck:
 "Fix a regression in mce-severity.c"

* tag 'please-pull-fix-mce-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  x86/mce: Fix mce regression from recent cleanup

Pull PCI fixes from Bjorn Helgaas:
 "Yinghai fixed a couple regressions: one resource assignment problem
  introduced in v3.10 that showed up with SR-IOV on powerpc, and another
  SR-IOV hot-remove issue related to refcounting changes we merged for
  v3.11.

  Yinghai is still working on another SR-IOV-related fix or two, which
  will be simpler if pciehp is non-modular, so I included the Kconfig
  changes now to get them in earlier.

  Finally, a minor fix for the ARM Marvell EBU host bridge driver that
  was merged for v3.11

  Hotplug:
      PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device
      PCI: hotplug: Convert to be builtin only, not modular
      PCI: pciehp: Convert pciehp to be builtin only, not modular

  Resource allocation:
      PCI: Retry allocation of only the resource type that failed

  ARM:
      PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge"

* tag 'pci-v3.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge
  PCI: Retry allocation of only the resource type that failed
  PCI: pciehp: Convert pciehp to be builtin only, not modular
  PCI: hotplug: Convert to be builtin only, not modular
  PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device

Pull ACPI and power management fixes from Rafael Wysocki:

 - Revert two cpuidle commits added during the 3.8 development cycle
   that turn out to have introduced a significant performance regression
   as requested by Jeremy Eder.

 - The recent patches that made the freezer less heavy-weight introduced
   a regression causing user-space-driven hibernation using the ioctl()
   interface to block indefinitely when the hibernate process executes
   try_to_freeze().  Fix from Colin Cross addresses this by adding a
   process flag to mark the hibernate/suspend process to inform the
   freezer that that process should be ignored.

 - One of the recent cpufreq reverts uncovered a problem in the core
   causing the cpufreq driver module refcount to become negative after a
   system suspend-resume cycle.  Fix from Rafael J Wysocki.

 - The evaluation of the ACPI battery _BIX method has never worked
   correctly, because the commit that added support for it forgot to
   take the "Revision" field in the return package into account.  As a
   result, the reading of battery info doesn't work at all on some
   systems, which is addressed by a fix from Lan Tianyu.

* tag 'pm+acpi-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  freezer: set PF_SUSPEND_TASK flag on tasks that call freeze_processes
  ACPI / battery: Fix parsing _BIX return value
  cpufreq: Fix cpufreq driver module refcount balance after suspend/resume
  Revert "cpuidle: Quickly notice prediction failure for repeat mode"
  Revert "cpuidle: Quickly notice prediction failure in general case"

The Marvell PCIe driver uses an emulated PCI-to-PCI bridge to be able
to dynamically set up MBus address decoding windows for PCI I/O and
memory regions depending on the PCI devices enumerated by Linux.

However, this emulated PCI-to-PCI bridge logic makes the Linux PCI
core believe that prefetchable memory regions are supported (because
the registers are read/write), while in fact no adress decoding window
is ever created for such regions. Since the Marvell MBus address
decoding windows do not distinguish memory regions and prefetchable
memory regions, this patch takes a simple approach: change the
PCI-to-PCI bridge emulation to let the Linux PCI core know that we
don't support prefetchable memory regions.

To achieve this, we simply make the prefetchable memory base a
read-only register that always returns 0. Reading/writing all the
other prefetchable memory related registers has no effect.

This problem was originally reported by Finn Hoffmann
<finn@uni-bremen.de>, who couldn't get a RTL8111/8168B PCI NIC working
on the NSA310 Kirkwood platform after updating to 3.11-rc. The problem
was that the PCI-to-PCI bridge emulation was making the Linux PCI core
believe that we support prefetchable memory, so the Linux PCI core was
only filling the prefetchable memory base and limit registers, which
does not lead to a MBus window being created. The below patch has been
confirmed by Finn Hoffmann to fix his problem on Kirkwood, and has
otherwise been successfully tested on the Armada XP GP platform with a
e1000e PCIe NIC and a Marvell SATA PCIe card.
Reported-by: Finn Hoffmann <finn@uni-bremen.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Commit 8bd26e3a (arm: delete __cpuinit/__CPUINIT usage from all ARM
users) caused some code to leak into sections which are discarded
through the removal of __CPUINIT annotations.  Add appropriate .text
annotations to bring these back into the kernel text.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If one process calls sys_reboot and that process then stops other
CPUs while those CPUs are within a spin_lock() region we can
potentially encounter a deadlock scenario like below.

CPU 0                   CPU 1
-----                   -----
                        spin_lock(my_lock)
smp_send_stop()
 <send IPI>             handle_IPI()
                         disable_preemption/irqs
                          while(1);
 <PREEMPT>
spin_lock(my_lock) <--- Waits forever

We shouldn't attempt to run any other tasks after we send a stop
IPI to a CPU so disable preemption so that this task runs to
completion. We use local_irq_disable() here for cross-arch
consistency with x86.
Reported-by: Sundarajan Srinivasan <sundaraj@codeaurora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If kuser helpers are not provided by the kernel, disable user access to
the vectors page.  With the kuser helpers gone, there is no reason for
this page to be visible to userspace.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move the signal handlers into a VDSO page rather than keeping them in
the vectors page.  This allows us to place them randomly within this
page, and also map the page at a random location within userspace
further protecting these code fragments from ROP attacks.  The new
VDSO page is also poisoned in the same way as the vector page.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

slots-fan on G5 Xserve is always running at full speed with windfarm_rm31
driver, resulting in a very high acoustic noise level. It seems the fan
parameters are incorrect, and have been copied from the Drive Bay fan
(RPM, not present on rm31) of the legacy therm_pm72 driver. This patch
changes the parameters to match the Slots fan (PWM) of therm_pm72. With
the patch, slots-fan speed drops from 99% to 19% during normal use,
and slots-temp settle to ~42'C.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

When an associativity level change is found for one thread, the
siblings threads need to be updated as well.  This is done today
for PRRN in stage_topology_update() but is missing for VPHN in
update_cpu_associativity_changes_mask().  This patch will correctly
update all thread siblings during a topology change.

Without this patch a topology update can result in a CPU in
init_sched_groups_power() getting stuck indefinitely in a loop.

This loop is built in build_sched_groups(). As a result of the thread
moving to a node separate from its siblings the struct sched_group will
have its next pointer set to point to itself rather than the sched_group
struct of the next thread.  This happens because we have a domain without
the SD_OVERLAP flag, which is correct, and a topology that doesn't conform
with reality (threads on the same core assigned to different numa nodes).
When this list is traversed by init_sched_groups_power() it will reach
the thread's sched_group structure and loop indefinitely; the cpu will
be stuck at this point.

The bug was exposed when VPHN was enabled in commit b7abef04 (v3.9).

Cc: <stable@vger.kernel.org> [v3.9+]
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We use bit 63 of the event code for userspace to request that the event
be counted using EBB (Event Based Branches). Export this value, making
it part of the API - though only on processors that support EBB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Back in commit 89713ed1 "Add timer, performance monitor and machine check
counts to /proc/interrupts" we added a count of PMU interrupts to the
output of /proc/interrupts.

At the time we named them "CNT" to match x86.

However in commit 89ccf465 "Rename 'performance counter interrupt'", the
x86 guys renamed theirs from "CNT" to "PMI".

Arguably changing the name could break someone's script, but I think the
chance of that is minimal, and it's preferable to have a name that 1) is
somewhat meaningful, and 2) matches x86.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull drm fixes from Dave Airlie:
 "Radeon, nouveau, exynos, intel, mgag200..

  Not all strictly regressions but there was probably only one patch I'd
  have really left out and it didn't seem worth respinning exynos to
  avoid it, the line change count is quite low.

   radeon: regressions + more dynamic powermanagement fixes, since DPM
     is a new feature, and off by default I'd prefer to keep merging
     fixes since it has a large userbase already and I'd like to keep
     them on mainline

   nouveau: is mostly regression fixes

   i915: is a regression fix since Daniel is on holidays I've merged it.

   mgag200: I've picked a bunch of targetted fixes from a big bunch of
     distro patches,

   exynos: build fixes mostly, one regression fix

  I expect things will slow right down now, I may send on the intel
  early quirk from Jesse separatly, since I think the x86 maintainers
  acked it"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
  drm/i915: fix missed hunk after GT access breakage
  drm/radeon/dpm: re-enable cac control on SI
  drm/radeon/dpm: fix calculations in si_calculate_leakage_for_v_and_t_formula
  drm: fix 64 bit drm fixed point helpers
  drm/radeon/atom: initialize more atom interpretor elements to 0
  drm/nouveau: fix semaphore dmabuf obj
  drm/nouveau/vm: make vm refcount into a kref
  drm/nv31/mpeg: don't recognize nv3x cards as having nv44 graph class
  drm/nv40/mpeg: write magic value to channel object to make it work
  drm/nouveau: fix size check for cards without vm
  drm/nv50-/disp: remove dcb_outp_match call, and related variables
  drm/nva3-/disp: fix hda eld writing, needs to be padded
  drm/nv31/mpeg: fix mpeg engine initialization
  drm/nv50/mc: include vp in the fb error reporting mask
  drm/nouveau: fix null pointer dereference in poll_changed
  drm/nv50/gpio: post-nv92 cards have 32 interrupt lines
  drm/nvc0/fb: take lock in nvc0_ram_put()
  drm/nouveau/core: xtensa firmware size needs to be 0x40000 no matter what
  drm/mgag200: Fix LUT programming for 16bpp
  drm/mgag200: Fix framebuffer pitch calculation
  ...

Pull fbdev fixes from Tomi Valkeinen:
 "Small fbdev fixes:
   - compile fixes
   - atyfb initialization fix
   - Fix freeing of the irq in sh7760fb & nuc900fb"

* tag 'fbdev-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  video: sh7760fb: fix to pass correct device identity to free_irq()
  fbdev/atyfb: fix recent breakage in correct_chipset()
  fbdev/sgivwfb: fix compilation error in sgivwfb_mmap()
  video: nuc900fb: fix to pass correct device identity to request_irq()
  vga16fb: Remove unused variable
  video: xilinxfb: Fix compilation warning

Pull vfio fixes from Alex Williamson:
 "misc fixes around overreacting to bus notifier events and a locking
  fix for a corner case blocked remove"

* tag 'vfio-v3.11-rc4' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Avoid deadlock on remove
  vfio: Ignore sprurious notifies
  vfio: Don't overreact to DEL_DEVICE

Merge more patches from Andrew Morton:
 "A bunch of fixes.

  Plus Joe's printk move and rework.  It's not a -rc3 thing but now
  would be a nice time to offload it, while things are quiet.  I've been
  sitting on it all for a couple of weeks, no issues"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  vmpressure: make sure there are no events queued after memcg is offlined
  vmpressure: do not check for pending work to prevent from new work
  vmpressure: change vmpressure::sr_lock to spinlock
  printk: rename struct log to struct printk_log
  printk: use pointer for console_cmdline indexing
  printk: move braille console support into separate braille.[ch] files
  printk: add console_cmdline.h
  printk: move to separate directory for easier modification
  drivers/rtc/rtc-twl.c: fix: rtcX/wakealarm attribute isn't created
  mm: zbud: fix condition check on allocation size
  thp, mm: avoid PageUnevictable on active/inactive lru lists
  mm/swap.c: clear PageActive before adding pages onto unevictable list
  arch/x86/platform/ce4100/ce4100.c: include reboot.h
  mm: sched: numa: fix NUMA balancing when !SCHED_DEBUG
  rapidio: fix use after free in rio_unregister_scan()
  .gitignore: ignore *.lz4 files
  MAINTAINERS: dynamic debug: Jason's not there...
  dmi_scan: add comments on dmi_present() and the loop in dmi_scan_machine()
  ocfs2/refcounttree: add the missing NULL check of the return value of find_or_create_page()
  mm: mempolicy: fix mbind_range() && vma_adjust() interaction

We can't use dev->mod_index for selecting the interrupt routing entry,
because it's not an index into interrupt routing table. It will be even
wrong on a machine with 2 CPUs (4 cores). But all needed information is
contained in the PAT entries for the serial ports. mod[0] contains the
iosapic address and mod_info has some indications for the interrupt
input (at least it looks like it). This patch implements the searching
for the right iosapic and uses this interrupt input information.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>

The KERNEL_SYSCALL define is not used anymore so the header can be
removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>

Signed-off-by: Helge Deller <deller@gmx.de>

Allow binding of user memory to the AGP GART on systems with HP
Quicksilver AGP bus. This resolves 'bind memory failed' error seen in
dmesg:

 [29.365973] [TTM] AGP Bind memory failed.
 …
 [29.367030] [drm] Forcing AGP to PCI mode

The system doesn't more fail to bind the memory, and hence not falling
back to the PCI mode (if other failures aren't detected).

This is just a simple write down from the following patches:
agp/amd-k7: Allow binding user memory to the AGP GART
agp/hp-agp: Allow binding user memory to the AGP GART
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>

The parisc architecture does not have a pte special bit. As a result,
special mappings are handled with the VM_PFNMAP and VM_MIXEDMAP flags.
VM_MIXEDMAP mappings may or may not have a "struct page" backing. When
pfn_valid() is false, there is no "struct page" backing. Otherwise, they
are treated as normal pages.

The FireGL driver uses the VM_MIXEDMAP without a backing "struct page".
This treatment caused a panic due to a TLB data miss in
update_mmu_cache. This appeared to be in the code generated for
page_address(). We were in fact using a very circular bit of code to
determine the physical address of the PFN in various cache routines.
This wasn't valid when there was no "struct page" backing.  The needed
address can in fact be determined simply from the PFN itself without
using the "struct page".

The attached patch updates update_mmu_cache(), flush_cache_mm(),
flush_cache_range() and flush_cache_page() to check pfn_valid() and to
directly compute the PFN physical and virtual addresses.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>

vmpressure is called synchronously from reclaim where the target_memcg
is guaranteed to be alive but the eventfd is signaled from the work
queue context.  This means that memcg (along with vmpressure structure
which is embedded into it) might go away while the work item is pending
which would result in use-after-release bug.

We have two possible ways how to fix this.  Either vmpressure pins memcg
before it schedules vmpr->work and unpin it in vmpressure_work_fn or
explicitely flush the work item from the css_offline context (as
suggested by Tejun).

This patch implements the later one and it introduces vmpressure_cleanup
which flushes the vmpressure work queue item item.  It hooks into
mem_cgroup_css_offline after the memcg itself is cleaned up.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Li Zefan <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

because it is racy and it doesn't give us much anyway as schedule_work
handles this case already.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Li Zefan <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There is nothing that can sleep inside critical sections protected by
this lock and those sections are really small so there doesn't make much
sense to use mutex for them.  Change the log to a spinlock
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Li Zefan <lizefan@huawei.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Rename the struct to enable moving portions of
printk.c to separate files.

The rename changes output of /proc/vmcoreinfo.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Make the code a bit more compact by always using a pointer for the active
console_cmdline.

Move overly indented code to correct indent level.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>