Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add dtb-y target into Makefile.boot, so that "make ARCH=arm dtbs" can
build out all the dtbs listed there.  It's very useful for build-testing
all the <board>.dts when imx28.dtsi changes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The enc28j60 spi device does not get converted to dts file, because
there is no mxs spi driver on mainline so far.  The enc28j60 spi
in mach-stmp378x_devb.c does not work anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

FEC support is missing because we need to find a proper way to rewrite
tx28_add_fec0 for device tree boot.

Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The presence and muxing of lcdif control pins can vary much on different
boards.  Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add flexan devices for imx28-evk board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

mx23-olinuxino is a low cost board designed by Olimex.

It has the following features:

- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output

More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.htmlSigned-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add DT node for gpmi nand.
Also add pinctrl for gpmi nand.

Enable the gpmi-nand in mx23-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add lcd support for imx23-evk and imx28-evk.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add pwm device and pwm-backlight for imx23-evk and imx28-evk.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable rtc for imx23 and imx28.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add heartbeat gpio-leds for imx28-evk board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.

Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand.  Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts.  Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add auart device for imx23-evk board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The 8-bit mode mmc has pin conflicts with display.  Let's use 4-bit
mode by default, so that display can be enabled together later.

Also add vmmc-supply for mmc device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add comments for pinmux-ids so that we do not have to keep looking at
Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt to read
all these pinmux-ids.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Use auxdata to attach mxsfb_platform_data for imx23-evk and imx28-evk.
We take this as a temporary solution for removing those board files,
and it should be updated to use common bindings for struct fb_videomode
when it becomes available.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add a simple device tree probe support for mxsfb driver.  Before
a common binding for struct fb_videomode is available, the driver will
keep using struct mxsfb_platform_data.  That said, platform code will
use auxdata to attach mxsfb_platform_data for device tree boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Move mxsfb.h into include/linux, so that mxsfb driver does not have to
include <mach/*> header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: rtc-linux@googlegroups.com
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

As the flexcan driver has DT binding for some time now. This patch makes
the flexcan driver available in the can drivers menu if a SOC with flexcan
is enabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The non-DT boot reads the mac from OTP and pass it to fec driver via
platform data.  The patch provides an equivalent support for device
tree boot, with reading mac from OTP and store it in device tree,
and fec driver can get the mac from device tree at its probe time.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add auart0 and auart3 support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Allow device tree probing.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: <linux-serial@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Subodh Nijsure <snijsure@grid-net.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Replace "gpmi" with "gpmi-nand" to get the
GPMI interface probing with DT instead of
failing to get clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
CC: Dong Aisheng <b29396@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

add gpmi-nand device tree support.
add gpmi-nand pinctrl support.

Also enable the gpmi support for mx28-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another batch of fixes.

  All are small, contained, targeted fixes for explicit problems --
  mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
  Samsung."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: imx6q: fix suspend regression caused by common clk migration
  ARM: OMAP4470: Fix OMAP4470 boot failure
  ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
  ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
  ARM: shmobile: r8a7779: Route all interrupts to ARM
  ARM: shmobile: kzm9d: use late init machine hook
  ARM: shmobile: kzm9g: use late init machine hook
  ARM: mach-shmobile: armadillo800eva: Use late init machine hook
  ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
  ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
  ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
  ARM: shmobile: sh7372: bugfix: chclr_offset base
  ARM: shmobile: sh73a0: bugfix: SY-DMAC number
  ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL

Fix kernel-doc warnings in printk.c: use correct parameter name.

  Warning(kernel/printk.c:2429): No description found for parameter 'buf'
  Warning(kernel/printk.c:2429): Excess function parameter 'line' description in 'kmsg_dump_get_buffer'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc warning.  This struct member was removed in commit
87568264 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.

  Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
  ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
  ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL

When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function.  There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>