Both Headset DAC need to be turned on/off at the same time before
any of the output drivers are enabled (HS Left/Right, Earpiece).
Move the HS DAC enable code to sequenced DAPM_SUPPLY, and attach
it to the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

twl6040 have two vibra output drivers.
They can be operated with audio stream coming through
the PDM interface (fifth channel).
The vibra outputs can be controlled via the input/FF
driver as well.
Selection between the two mode is implemented within
the codec driver, the input/FF driver can only operate if
the routing is set to "Input FF".
Changing from "Input FF" to "Audio PDM" mode is protected
as well: The switchin can only be done, if there is no
running effect from the input/FF.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The VIBSELL/R bit in the VIBCTLL/R register tells the source of the data,
which is going to be used to drive the attached motor(s).
Do not allow effect execution if any of the channels are set to receive
audio data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If the client only interested, if any of the vibra channels enabled, or
if any of the channels are set to receive audio data via PDM.

This function targets mainly the vibra driver, so it can check if it is
allowed to execute effects ot not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The vibra control register will be used from the ASoC codec driver as well.
In order to avoid latency issues caused by I2C read access, cache the two
control register within the core driver, so we do not need to reach out
to the chip to read it back.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The bits within the two control registers (for left and right channel)
are identical.
Use common names for the bits acros the two register.
Also add the missing definition for the path selection bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We set hw_params callback for wm8994_aif3_dai_ops to wm8994_aif3_hw_params.
Thus no need to check wm8994-aif3 in wm8994_hw_params.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is not required after multi-component patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This ensures they are available prior to the card late_probe().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM5100 includes an advanced, low power, accessory detect subsystem
capable of detecting both accessory presence and button presses while
the device is in an ultra low power mode. Implement initial support for
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

It is currently named "TVL" instead of "TLV".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM8983 can be reset by performing a write of any value to
the software reset register.
To avoid writing to the software reset register while resume,
we should write the same value in wm8983_reg_defs to software
reset register in wm8983_probe().
The write to the reset register is suppressed by the cache
restore code when it skips writes of default registers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pass the DAPM widgets/routes and static controls via the
snd_soc_card struct to core. In this way the machine driver
does not need to handle the DAPM widgets/routes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Widgets are connected by default.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Widgets are connected by default.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

No need to call soc_dapm_sync at init time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Michael Opdenacker <michael.opdenacker@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>