- 05 May, 2019 40 commits
-
-
Guenter Roeck authored
HPWDT_NMI_DECODING depends on HP_WATCHDOG and should be next to it. This helps menuconfig identify HPWDT_NMI_DECODING as depending on HP_WATCHDOG. BCM_KONA_WDT_DEBUG depends on BCM_KONA_WDT which depends on COMPILE_TEST. Enabling BCM_KONA_WDT_DEBUG without BCM_KONA_WDT does not make sense, so drop the COMPILE_TEST dependency from it. This also improves menuconfig, which now properly associates BCM_KONA_WDT_DEBUG with BCM_KONA_WDT. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Most of the NPCM7XX drivers can be built as modules. The NPCM7XX watchdog driver code supports building it as module, but its configuration option is set to bool. Make itr tristate to actually support modular builds. This improves consistency with other drivers for the same platform and enables including the driver in multi- platform configurations. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Under some circumstances it may be desirable to configure the watchdog core as module. Enable it. As part of this change, mark pretimeout governors as depending on the watchdog core. This is necessary to prevent governors from being built into the kernel if the watchdog core is built as module. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Watchdog pretimeout configuration was at the end of the Kconfig file, after individual watchdog drivers, and thus easy to miss. Move it right after basic watchdog option declarations. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Watchdog pretimeout governors were enabled from the default governor selection using "select". As a result, the default governor was always built into the kernel, even if no watchdog driver was loaded. By using "depends on" instead of "select", we are in better control, and the governors can all be built as modules. At the same time, set the default configuration option for pretimeout governors to match WATCHDOG_CORE (meaning all pretimeout governors are by default enabled if pretimeout support is enabled). The practical impact of this change is minimal. Previously, selecting a default governor automatically enabled that governor. Now, a default governor can only be selected if that governor has been enabled. Consequently, the order of governor selection is now reversed: The governor selection is now first, followed by default governor selection. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Paul Gortmaker authored
The Kconfig for this driver is: config RTD119X_WATCHDOG bool "Realtek RTD118x/RTD129x watchdog support" ...and hence it doesn't need to include module.h for anything. There are no other signs of unused modular infrastructure. Cc: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-watchdog@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Paul Gortmaker authored
The Kconfig currently controlling compilation of this code is: config INTEL_SCU_WATCHDOG bool "Intel SCU Watchdog for Mobile Platforms" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. We leave the moduleparam.h include since the file does declare some module parameters, and leaving them as such is currently the easiest way to remain compatible with existing boot arg use cases. Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-watchdog@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Paul Gortmaker authored
The Kconfig currently controlling compilation of this code is: config COH901327_WATCHDOG bool "ST-Ericsson COH 901 327 watchdog" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. We explicitly disallow a driver unbind, since that doesn't have a sensible use case anyway, and it allows us to drop the ".remove" code for non-modular drivers. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_ALIAS is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. We replace module.h with moduleparam.h since the file does actually declare some module parameters (i.e. boot args for non-modules). Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-watchdog@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
We have a default timeout value in the driver which we will fall back to if the user supplied values are out of bounce. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The core will print out details now. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
This not only removes boilerplate code from watchdog drivers, it can also be more specific which of the supplied value actually fails. Also, the loglevel becomes now consistent across drivers. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
The function is not easy to read and has a problem: -EINVAL is returned when the module parameter is invalid but the DT parameter is OK. Refactor the code to have the same pattern of checks for the module parameter and DT. Further ones can be easily added in the future if the need arises. The above mentioned problem is fixed, too. Some documentation is added to describe the different handlings of '0' for the module parameter and the DT property. Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
If we want to match all revisions, it is enough to leave the field empty. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Wolfram Sang authored
And make sure the final obtained value gets properly scaled. Remove two empty lines to group the initialization blocks while we are here. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Steve Twiss <stwiss.opensource@diasemi.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Colin Ian King authored
There is a spelling mistake in a pr_debug message. Fix it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Alexandre Belloni authored
Readout the enabled state so it is possible to get the pre-userspace handler working. Also, avoid disabling the watchdog to ensure it continues working and triggers if there is an issue later in the boot or if userspace fails to start. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. This patch fixes the following warnings: drivers/watchdog/machzwd.c: In function ‘zf_set_timer’: ./arch/x86/include/asm/io.h:355:14: warning: this statement may fall through [-Wimplicit-fallthrough=] #define outw outw drivers/watchdog/machzwd.c:80:53: note: in expansion of macro ‘outw’ #define zf_writew(port, data) { outb(port, INDEX); outw(data, DATA_W); } ^~~~ drivers/watchdog/machzwd.c:179:3: note: in expansion of macro ‘zf_writew’ zf_writew(COUNTER_1, new); ^~~~~~~~~ drivers/watchdog/machzwd.c:180:2: note: here case WD2: ^~~~ Warning level 3 was used: -Wimplicit-fallthrough=3 This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop empty remove function - Use devm_add_action_or_reset() for calls to clk_disable_unprepare - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop assignments to otherwise unused variables - Drop empty remove function This also drops the inaccurate message on remove; the driver won't be removed if the hardware watchdog is running, no matter if the watchdog device is open or not. - Use local variable 'struct device *dev' consistently - Use devm_watchdog_register_driver() to register watchdog device Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly. Also, there is no call to dev_get_drvdata() or platform_get_drvdata() in the driver, so drop the unnecessary call to platform_set_drvdata(). The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patchesSigned-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop empty remove function - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device - Replace shutdown function with call to watchdog_stop_on_reboot() Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches Cc: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop assignments to otherwise unused variables - Drop unnecessary braces around conditional return statements - Drop empty remove function - Use devm_add_action_or_reset() for calls to clk_disable_unprepare - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device Cc: Keguang Zhang <keguang.zhang@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop assignments to otherwise unused variables - Drop empty remove function - Use devm_add_action_or_reset() for calls to clk_disable_unprepare - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop assignments to otherwise unused variables - Drop empty remove function - Use devm_add_action_or_reset() for calls to clk_disable_unprepare - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop empty remove function - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop assignments to otherwise unused variables - Drop empty remove function - Use devm_add_action_or_reset() for calls to clk_disable_unprepare - Introduce local variable 'struct device *dev' and use it instead of dereferencing it repeatedly - Use devm_watchdog_register_driver() to register watchdog device Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-
Guenter Roeck authored
Use device managed functions to simplify error handling, reduce source code size, improve readability, and reduce the likelyhood of bugs. Other improvements as listed below. The conversion was done automatically with coccinelle using the following semantic patches. The semantic patches and the scripts used to generate this commit log are available at https://github.com/groeck/coccinelle-patches - Drop assignments to otherwise unused variables - Drop empty remove function - Use devm_add_action_or_reset() for calls to clk_disable_unprepare - Use local variable 'struct device *dev' consistently - Use devm_watchdog_register_driver() to register watchdog device Cc: Jun Nie <jun.nie@linaro.org> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-