- 01 Jul, 2013 9 commits
-
-
Kevin Hao authored
For an unknown relocation type since the value of r4 is just the 8bit relocation type, the sum of r4 and r7 may yield an invalid memory address. For example: In normal case: r4 = c00xxxxx r7 = 40000000 r4 + r7 = 000xxxxx For an unknown relocation type: r4 = 000000xx r7 = 40000000 r4 + r7 = 400000xx 400000xx is an invalid memory address for a board which has just 512M memory. And for operations such as dcbst or icbi may cause bus error for an invalid memory address on some platforms and then cause the board reset. So we should skip the flush/invalidate the d/icache for an unknown relocation type. Signed-off-by:Kevin Hao <haokexin@gmail.com> Acked-by:
Suzuki K. Poulose <suzuki@in.ibm.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org>
-
Aaro Koskinen authored
With pm81/pm91/pm121, when the overtemperature state is entered, and when it remains on after skipped ticks, the driver will try to leave it too soon (immediately on the next tick). This is because the active FAILURE_OVERTEMP state is not visible in "new_failure" variable of the current tick. Furthermore, the driver will keep trying to clear condition in subsequent ticks as FAILURE_OVERTEMP remains set in the "last_failure" variable. These will start to trigger WARNINGS from windfarm core: [ 100.082735] windfarm: Clamping CPU frequency to minimum ! [ 100.108132] windfarm: Overtemp condition detected ! [ 101.952908] windfarm: Overtemp condition cleared ! [...] [ 102.980388] WARNING: at drivers/macintosh/windfarm_core.c:463 [...] [ 103.982227] WARNING: at drivers/macintosh/windfarm_core.c:463 [...] [ 105.030494] WARNING: at drivers/macintosh/windfarm_core.c:463 [...] [ 105.973666] WARNING: at drivers/macintosh/windfarm_core.c:463 [...] [ 106.977913] WARNING: at drivers/macintosh/windfarm_core.c:463 Fix by adding a helper global variable. We leave the overtemp state only after all failure bits have been cleared. I saw this error on iMac G5 iSight (pm121). Also pm81/pm91 are fixed based on the observation that these are almost identical/copy-pasted code. Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Gavin Shan authored
Currently, we're using the combo (PCI bus + devfn) in the PCI config accessors and PCI config accessors in EEH depends on them. However, it's not safe to refer the PCI bus which might have been removed during hotplug. So we're using device node in the PCI config accessors and the corresponding backends just reuse them. The patch also fix one potential risk: We possiblly have frozen PE during the early PCI probe time, but we haven't setup the PE mapping yet. So the errors should be counted to PE#0. Signed-off-by:
Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by:
-
Gavin Shan authored
The patch is for avoiding following build warnings: The function .pnv_pci_ioda_fixup() references the function __init .eeh_init(). This is often because .pnv_pci_ioda_fixup lacks a __init The function .pnv_pci_ioda_fixup() references the function __init .eeh_addr_cache_build(). This is often because .pnv_pci_ioda_fixup lacks a __init Signed-off-by:
-
Gavin Shan authored
We needn't the the whole backtrace other than one-line message in the error reporting interrupt handler. For errors triggered by access PCI config space or MMIO, we replace "WARN(1, ...)" with pr_err() and dump_stack(). The patch also adds more output messages to indicate what EEH core is doing. Besides, some printk() are replaced with pr_warning(). Signed-off-by:
-
Gavin Shan authored
On the PowerNV platform, the EEH address cache isn't built correctly because we skipped the EEH devices without binding PE. The patch fixes that. Signed-off-by:
-
Gavin Shan authored
We have 2 fields in "struct pnv_phb" to trace the states. The patch replace the fields with one and introduces flags for that. The patch doesn't impact the logic. Signed-off-by:
-
Gavin Shan authored
After reset (e.g. complete reset) in order to bring the fenced PHB back, the PCIe link might not be ready yet. The patch intends to make sure the PCIe link is ready before accessing its subordinate PCI devices. The patch also fixes that wrong values restored to PCI_COMMAND register for PCI bridges. Signed-off-by:
-
Gavin Shan authored
When the PHB is fenced or dead, it's pointless to collect the data from PCI config space of subordinate PCI devices since it should return 0xFF's. The patch also fixes overwritten buffer while getting PCI config data. Signed-off-by:
-
- 30 Jun, 2013 3 commits
-
-
Michael Neuling authored
When we treclaim and trecheckpoint there's an unavoidable period when r1 will not be a valid kernel stack pointer. This patch clears the MSR recoverable interrupt (RI) bit over these regions to indicate we have an invalid kernel stack pointer. For treclaim, the region over which we clear MSR RI is larger than required to avoid the need for an extra costly mtmsrd. Thanks to Paulus for suggesting this change. Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
James Yang authored
String instruction emulation would erroneously result in a segfault if the upper bits of the EA are set and is so high that it fails access check. Truncate the EA to 32 bits if the process is 32-bit. Signed-off-by:
James Yang <James.Yang@freescale.com> Signed-off-by:
-
Sebastien Bessiere authored
Signed-off-by:
Sebastien Bessiere <sebastien.bessiere@gmail.com> Signed-off-by:
-
- 25 Jun, 2013 8 commits
-
-
Kirill A. Shutemov authored
Currently, HPAGE_PMD_* constans rely on PMD_SHIFT regardless of CONFIG_TRANSPARENT_HUGEPAGE. PMD_SHIFT is not defined everywhere (e.g. arm nommu case). It means we can't use anything like this in generic code: if (PageTransHuge(page)) zero_huge_user(page, 0, HPAGE_PMD_SIZE); else clear_highpage(page); For !THP case, PageTransHuge() is 0 and compiler can eliminate zero_huge_user() call. But it still need to be valid C expression, means HPAGE_PMD_SIZE has to expand to something compiler can understand. Previously, HPAGE_PMD_* were defined to BUILD_BUG() for !THP. Let's come back to it. Signed-off-by:Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Gavin Shan authored
To replace down() with down_interrutible() to avoid following warning: [c00000007ba7b710] [c000000000014410] .__switch_to+0x1b0/0x380 [c00000007ba7b7c0] [c0000000007b408c] .__schedule+0x3ec/0x970 [c00000007ba7ba50] [c0000000007b1f24] .schedule_timeout+0x1a4/0x2b0 [c00000007ba7bb30] [c0000000007b34a4] .__down+0xa4/0x104 [c00000007ba7bbf0] [c0000000000b9230] .down+0x60/0x70 [c00000007ba7bc80] [c0000000000336d0] .eeh_event_handler+0x70/0x190 [c00000007ba7bd30] [c0000000000b1a58] .kthread+0xe8/0xf0 [c00000007ba7be30] [c00000000000a05c] .ret_from_kernel_thread+0x5c/0x8 This also avoids keeping the load average up while doing nothing. Signed-off-by:
-
Gavin Shan authored
Originally, eeh_mutex was introduced to protect the PE hierarchy tree and the attached EEH devices because EEH core was possiblly running with multiple threads to access the PE hierarchy tree. However, we now have only one kthread in EEH core. So we needn't the eeh_mutex and just remove it. Signed-off-by:
-
Nathan Fontenot authored
Building with CONFIG_TRANSPARENT_HUGEPAGE disabled causes the following build wearnings; powerpc/arch/powerpc/include/asm/mmu-hash64.h: In function ‘__hash_page_thp’: powerpc/arch/powerpc/include/asm/mmu-hash64.h:354: warning: no return statement in function returning non-void This patch adds a return -1 to the static inline for __hash_page_thp() to correct the warnings. Signed-off-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Reviewed-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
-
Aruna Balakrishnaiah authored
Since now we have pstore support for nvram in pseries, enable it in the default config. With this config option enabled, pstore infra-structure will be used to read/write the messages from/to nvram. Signed-off-by:
Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com> Acked-by:
-
Michael Neuling authored
In 9422de3e "powerpc: Hardware breakpoints rewrite to handle non DABR breakpoint registers" we changed the way we mark extraneous irqs with this: - info->extraneous_interrupt = !((bp->attr.bp_addr <= dar) && - (dar - bp->attr.bp_addr < bp->attr.bp_len)); + if (!((bp->attr.bp_addr <= dar) && + (dar - bp->attr.bp_addr < bp->attr.bp_len))) + info->type |= HW_BRK_TYPE_EXTRANEOUS_IRQ; Unfortunately this is bogus as it never clears extraneous IRQ if it's already set. This correctly clears extraneous IRQ before possibly setting it. Signed-off-by:
Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Michael Neuling authored
The smallest match region for both the DABR and DAWR is 8 bytes, so the kernel needs to filter matches when users want to look at regions smaller than this. Currently we set the length of PPC_BREAKPOINT_MODE_EXACT breakpoints to 8. This is wrong as in exact mode we should only match on 1 address, hence the length should be 1. This ensures that the kernel will filter out any exact mode hardware breakpoint matches on any addresses other than the requested one. Signed-off-by:
-
Robert P. J. Day authored
Signed-off-by:
Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by:
-
- 21 Jun, 2013 20 commits
-
-
Aneesh Kumar K.V authored
Hugepage invalidate involves invalidating multiple hpte entries. Optimize the operation using H_BULK_REMOVE on lpar platforms. On native, reduce the number of tlb flush. Signed-off-by:
-
Aneesh Kumar K.V authored
We enable only if the we support 16MB page size. Reviewed-by:
David Gibson <dwg@au1.ibm.com> Signed-off-by:
-
Aneesh Kumar K.V authored
We find all the overlapping vma and mark them such that we don't allocate hugepage in that range. Also we split existing huge page so that the normal page hash can be invalidated and new page faulted in with new protection bits. Signed-off-by:
-
Aneesh Kumar K.V authored
With THP we set pmd to none, before we do pte_clear. Hence we can't walk page table to get the pte lock ptr and verify whether it is locked. THP do take pte lock before calling pte_clear. So we don't change the locking rules here. It is that we can't use page table walking to check whether pte locks are held with THP. Signed-off-by:
-
Aneesh Kumar K.V authored
GCC is very likely to read the pagetables just once and cache them in the local stack or in a register, but it is can also decide to re-read the pagetables. The problem is that the pagetable in those places can change from under gcc. With THP/hugetlbfs the pmd (and pgd for hugetlbfs giga pages) can change under gup_fast. The pages won't be freed untill we finish gup fast because we have irq disabled and we free these pages via rcu callback. Signed-off-by:
-
Aneesh Kumar K.V authored
We need to have irqs disabled to handle all the possible parallel update for linux page table without holding locks. Events that we are intersted in while walking page tables are 1) Page fault 2) umap 3) THP split 4) THP collapse A) local_irq_disabled: ------------------------ 1) page fault: A none to valid transition via page fault is not an issue because we would either see a none or valid. If it is none, we would error out the page table walk. We may need to use on stack values when checking for type of page table elements, because if we do if (!is_hugepd()) { if (!pmd_none() { if (pmd_bad() { We could take that bad condition because the pmd got converted to a hugepd after the !is_hugepd check via a hugetlb fault. The right way would be to check for pmd_none higher up or use on stack value. 2) A valid to none conversion via unmap: We can safely walk the upper level table, because we don't remove the the page table entries until rcu grace period. So even if we followed a wrong pointer we still have the pointer valid till the grace period. A PTE pointer returned need to be atomically checked for _PAGE_PRESENT and _PAGE_BUSY. A valid pointer returned could becoming none later. To prevent pte_clear we take _PAGE_BUSY. 3) THP split: A valid transparent hugepage is converted to nomal page. Before we split we do pmd_splitting_flush, which sets the hugepage PTE to _PAGE_SPLITTING So when walking page table we need to check for pmd_trans_splitting and handle that. The pte returned should also need to be checked for _PAGE_SPLITTING before setting _PAGE_BUSY similar to _PAGE_PRESENT. We save the value of PTE on stack and check for the flag in the local pte value. If we don't have the value set we can safely operate on the local pte value and we atomicaly set _PAGE_BUSY. 4) THP collapse: A normal page gets converted to hugepage. In the collapse path, we mark the pmd none early (pmdp_clear_flush). With irq disabled, if we are aleady walking page table we would see the pmd_none and won't continue. If we see a valid PMD, we should still check for _PAGE_PRESENT before setting _PAGE_BUSY, to make sure we didn't collapse the PTE to a Huge PTE. Signed-off-by: -
Aneesh Kumar K.V authored
The deposted PTE page in the second half of the PMD table is used to track the state on hash PTEs. After updating the HPTE, we mark the coresponding slot in the deposted PTE page valid. Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
-
Aneesh Kumar K.V authored
Reviewed-by:
-
Aneesh Kumar K.V authored
We can find pte that are splitting while walking page tables. Return None pte in that case. Signed-off-by:
-
Aneesh Kumar K.V authored
Replace find_linux_pte with find_linux_pte_or_hugepte and explicitly document why we don't need to handle transparent hugepages at callsites. Signed-off-by:
-
Aneesh Kumar K.V authored
Reviewed-by:
-
Aneesh Kumar K.V authored
We will use this in the later patch for handling THP pages Reviewed-by:
-
Aneesh Kumar K.V authored
We now have pmd entries covering 16MB range and the PMD table double its original size. We use the second half of the PMD table to deposit the pgtable (PTE page). The depoisted PTE page is further used to track the HPTE information. The information include [ secondary group | 3 bit hidx | valid ]. We use one byte per each HPTE entry. With 16MB hugepage and 64K HPTE we need 256 entries and with 4K HPTE we need 4096 entries. Both will fit in a 4K PTE page. On hugepage invalidate we need to walk the PTE page and invalidate all valid HPTEs. This patch implements necessary arch specific functions for THP support and also hugepage invalidate logic. These PMD related functions are intentionally kept similar to their PTE counter-part. Signed-off-by:
-
Aneesh Kumar K.V authored
THP code does PTE page allocation along with large page request and deposit them for later use. This is to ensure that we won't have any failures when we split hugepages to regular pages. On powerpc we want to use the deposited PTE page for storing hash pte slot and secondary bit information for the HPTEs. We use the second half of the pmd table to save the deposted PTE page. Reviewed-by:
-
Aneesh Kumar K.V authored
If a hash bucket gets full, we "evict" a more/less random entry from it. When we do that we don't invalidate the TLB (hpte_remove) because we assume the old translation is still technically "valid". This implies that when we are invalidating or updating pte, even if HPTE entry is not valid we should do a tlb invalidate. With hugepages, we need to pass the correct actual page size value for tlb invalidation. This change update the patch 0608d692 "powerpc/mm: Always invalidate tlb on hpte invalidate and update" to handle transparent hugepages correctly. Signed-off-by:
-
Gavin Shan authored
The patch creates debugfs entries (powerpc/PCIxxxx/err_injct) for injecting EEH errors for testing purpose. Signed-off-by:
-
Gavin Shan authored
The patch creates one debugfs directory ("powerpc/PCIxxxx") for each PHB so that we can hook EEH error injection debugfs entry there in proceeding patch. Signed-off-by: -
Gavin Shan authored
The patch registers OPAL event notifier and process the PCI errors from firmware. If we have pending PCI errors, special EEH event (without binding PE) will be sent to EEH core for processing. Signed-off-by:
-
Gavin Shan authored
While we're restarting or powering off the system, we needn't the OPAL notifier any more. So just to disable that. Signed-off-by:
-
Gavin Shan authored
This patch implements a notifier to receive a notification on OPAL event mask changes. The notifier is only called as a result of an OPAL interrupt, which will happen upon reception of FSP messages or PCI errors. Any event mask change detected as a result of opal_poll_events() will not result in a notifier call. [benh: changelog] Signed-off-by:
-
