In preparation to Device Tree support.
With DT booted kernel we can not rely on pdata which used to
hold information needed for the driver at runtime.
Use the card's driver data to hold these informations from now on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

The needed change in routing will be done runtime for the non
twl6040 connected widgets, like the Digital microphone.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

There is no need to have two snd_soc_dai_link structure for the two setup
the machine driver supports.
We can just tell core to register only the first link if the DMIC link is
not in use on the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

Device tree support for OMAP4+ dmic cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

Device tree support for OMAP4+ McPDM cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

In capture stream the buffer size does not need to be constrained to be
bigger then the McBSP FIFO.
In capture the FIFO content is taken out in period length burst, this
enusres that the FIFO is not going to overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

With the common irq the driver only needs to use one interrupt line, and
it provides better debugging possibilites compared to the legacy TX/RX
interrupt lines.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

The frame dma_op_mode has never been used, and it is just creating
confusion for users/developers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

Take the DMA packet mode into use when the McBSP is configured in element
dma_op_mode if the stream is not mono.
In this way we transfer one sample from/to McBSP FIFO upon DMA request.
This change only affects OMAP3+ versions, where the McBSP ports have FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

SupherH FSI2 can use special data transfer,
but it depends on CPU-FSI2 connection style.

We can use 16bit data stream mode if it was valid connection,
and it is required for 16bit data DMA transfer / SPDIF sound output.
We can use 24bit data transfer if it was invalid connection.

We can select connection type if CPU is SH7372,
and it is always valid connection if latest SuperH.

This patch adds new bus_option and fsi_bus_setup()
for supporting these feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

fsi_hw_startup/shutdown() needs the setup of bus width,
but it is impossible to get parameter of snd_pcm_runtime at this timing.
So, these functions are changed so that be called from fsi_dai_trigger().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds fsi_version() function for accessing version.

And there were some meaningless version check which never hit.
This patch removed it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

One such machine is Whistler.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Commit 4924082 "ASoC: core: Flip master for CODECs in the CPU slot of a
CODEC<->CODEC link" added code that was conditional on there being no
PCM/DMA driver for the link. However, it failed to cover the case where
the link was instantiated from device tree, and hence was specified by
DT node rather than name.

This prevents the following error on Toshiba AC100:
aplay: pcm_write:1603: write error: Input/output error
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Supports regmap conversion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

aic3x_set_headset_detection() isn't made available outside the driver or
referenced within the driver which sparse notices and complains about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In preparation for irq_domain support change the code to the not switch
based on the irq number. This actually makes things simpler, if slightly
repetitive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There's no space for the sign bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Linux 3.4-rc7

Conflicts):
	drivers/base/regmap/regmap.c         (overlap with bug fixes)
	sound/soc/blackfin/bf5xx-ssm2602.c   (overlap with bug fixes)

.. and this should hopefully be the last -rc before final 3.4 release.

Pull ARM: SoC fixes from Olof Johansson:
 "I was hoping to be done with fixes for 3.4 but we got two branches
  from subarch maintainers the last couple of days.  So here is one
  last(?) pull request for arm-soc containing 7 patches:

   - Five of them are for shmobile dealing with SMP setup and compile
     failures
   - The remaining two are for regressions on the Samsung platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
  ARM: EXYNOS: use s5p-timer for UniversalC210 board
  ARM / mach-shmobile: Invalidate caches when booting secondary cores
  ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
  ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
  ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
  ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper

Pull a few more GPIO bug fixes from Grant Likely:
 "Oops, missed a couple.  Here's an updated pull req for GPIO"

A set of PCH bug fixes, and one patch to fix up compile warnings

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  gpio/exynos: Fix compiler warnings when non-exynos machines are selected
  gpio: pch9: Use proper flow type handlers

Merge branch 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
  ARM: EXYNOS: use s5p-timer for UniversalC210 board

It should be (1 << 2) for ctrlbit of exynos5_clk_pdma1.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Commit 069d4e74 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms.  Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
  ARM / mach-shmobile: Invalidate caches when booting secondary cores
  ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
  ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
  ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
  ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper

Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.

Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Fix SMP TWD boot regression on sh73a0 based platforms caused by:

4200b16d ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.

This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>