Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).

If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.

This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.

Notes from Sarah:

Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2

This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver.  Commit
638c5115 "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg).  Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.

This patch only fixes the issue for bulk endpoint scatter-gather.  The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.

Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints.  Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed.  The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.

This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115 "USBNET: support DMA
SG".  Without this patch, the USB network device gets wedged, and stops
sending packets.  Mark Lord confirms this patch fixes the regression:

http://marc.info/?l=linux-netdev&m=138487107625966&w=2Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: stable@vger.kernel.org

Merge tag 'fixes-for-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.13-rc2

First set of fixes for this -rc cycle. A few important
fixes which should be backported to stable kernels and
the usual set of sparse warning fixes. There's also a
regression fix on phy-generic.c which would prevent
am335x-based platforms from having their PHY drivers
probed.
Signed-of-by: Felipe Balbi <balbi@ti.com>

Call try_to_freeze() in sleep_thread() only when it's safe to sleep.
do_read() and do_write() calls sleep_thread with lock held.
Make sure these won't call try_to_freeze() by passing can_freeze flag
to sleep_thread.

Calling try_to_freeze() with a lock hold was done since day one in
f_mass_storage but since commit 0f9548ca ("lockdep: check that no
locks held at freeze time") lockdep complains about it.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

that symbol is only used inside this function driver,
we should mark it static. Fixes sparse's:

drivers/usb/gadget/tcm_usb_gadget.c:373:6: warning: symbol \
	'bot_cleanup_old_alt' was not declared. Should it \
	be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>

use NULL instead of 0 as pointer.
Signed-off-by: Felipe Balbi <balbi@ti.com>

g_zero's module parameters can, and should, be
static. This fixes sparse warnings.

Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

fsg_common_set_inquiry_string() expects pointers
as second and third argument. Let's fix that by
passing NULL instead of plain 0 just so we silence
sparse's:

drivers/usb/gadget/f_mass_storage.c:3114:60: warning: \
	Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3114:63: warning: \
	Using plain integer as NULL pointer
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add missing USB UGCTRL2 register offset.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt().  Only the host is
prevented from resetting the endpoint.

This patch fixes the implementation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Mass storage gadget returns DELAYED_STATUS in stead of
USB_GADGET_DELAYED_STATUS while handling bulk reset request. Since
peripheral driver uses USB_GADGET_DELAYED_STATUS for delayed status
handling, therefore replace DELAYED_STATUS by USB_GADGET_DELAYED_STATUS
in mass storage driver.

Since, DELAYED_STATUS and hence EP0_BUFSIZE will no longer be used now,
so remove them.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Cc: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Legacy gadgets supporting mass storage (g_mass_storage, g_acm_ms, g_multi)
all depend on BLOCK.

Make the standalone compilation of f_mass_storage (without any legacy
gadget) dependent no BLOCK, too.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We need to set mxs_phy rather as the platform drvdata so that we can get
the correct mxs_phy in mxs_phy_remove().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since commit c5340bd1 ("usb: musb: cancel work on removal") the workqueue
is cancelled but then if we bail out before the workqueue is setup we
get this:

|INFO: trying to register non-static key.
|the code is fine but needs lockdep annotation.
|turning off the locking correctness validator.
|CPU: 0 PID: 708 Comm: modprobe Not tainted 3.12.0+ #435
|[<c00867bc>] (lock_acquire+0xf0/0x108) from [<c00529d0>] (flush_work+0x38/0x2ec)
|[<c00529d0>] (flush_work+0x38/0x2ec) from [<c0052d24>] (__cancel_work_timer+0xa0/0x134)
|[<c0052d24>] (__cancel_work_timer+0xa0/0x134) from [<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc])
|[<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc]) from [<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc])
|[<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|[<c0294bf0>] (platform_drv_probe+0x1c/0x24) from [<c0293970>] (driver_probe_device+0x90/0x224)
|[<c0293970>] (driver_probe_device+0x90/0x224) from [<c0291ef0>] (bus_for_each_drv+0x60/0x8c)
|[<c0291ef0>] (bus_for_each_drv+0x60/0x8c) from [<c02938bc>] (device_attach+0x80/0xa4)
|[<c02938bc>] (device_attach+0x80/0xa4) from [<c0292b24>] (bus_probe_device+0x88/0xac)
|[<c0292b24>] (bus_probe_device+0x88/0xac) from [<c0291490>] (device_add+0x388/0x6c8)
|[<c0291490>] (device_add+0x388/0x6c8) from [<c02952a0>] (platform_device_add+0x188/0x22c)
|[<c02952a0>] (platform_device_add+0x188/0x22c) from [<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps])
|[<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral
|musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517

This patch moves the init part to earlier part so it can be cleaned as
part of the fail3 label because now it is surrounded by the fail4 label.
Step two is to remove it from musb_free() and add it to the two cleanup
paths (error path and device removal) separately.

Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The delayed_status value is used to keep track of status response
packets on ep0. It needs to be reset or the set_config function would
still delay the answer, if the usb device got unplugged while waiting
for setup_continue to be called.

Cc: stable@vger.kernel.org
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The TX-complete interrupt of the CPPI41 on AM335x fires too early.
Adding a loop and counting how long it takes until the
MUSB_TXCSR_TXPKTRDY bit is cleared I see
FS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1
|cppi41_dma_callback() 74 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1
|cppi41_dma_callback() 66 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops

avg: 110 - 150us

HS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1
|cppi41_dma_callback() 0 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1
|cppi41_dma_callback() 2 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1
|cppi41_dma_callback() 13 loops

avg: 2us

for the same test case. One loop means a udelay(1). The delay seems to
depend on the packet size. On HS the bit is always cleared for small
packet sizes while on FS it is never the case, it mostly around 110us.
This testing has been performed with g_ether (musb as device) and using BULK
transfers.

INTR transfers are way more fun: during init the gadget sends a INT
packet to the host and cppi41 says "transfer done" shortly after. The
MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host
did not try to receive it, it does so after the interface (on host side) has
been configured. Until this happens, that packet remains in musb's FIFO.

To fix this, two things are done:
- No DMA transfers for INT based endpoints. These transfer are usually
  very small and rare so it is likely better to skip the DMA engine and
  stuff the four bytes directly into the FIFO
- on HS we poll up to 25us and hope that bit goes away. If not we setup
  a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS
  the command
  | ping 10.10.10.10 -c1 -s65130
  creates about 44 1514bytes transfers. About 19 of them need a second
  timer to complete.
Reported-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves most of the logic in cppi41_dma_callback() into
cppi41_trans_done() where it can be called from another function.
Instead of computing "transferred" (the number of bytes transferred in
the last transaction) in cppi41_trans_done() the member
"cppi41_channel->prog_len" is now set to 0 if the transfer as a whole
can be considered as done. If it is != 0 then the next iteration is
assumed.
This is a preparation for a workaround.

Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix regression introduced by commit 818f6036 ("USB: serial: add
memory flags to usb_serial_generic_write_start"), which incorrectly used
GFP_KERNEL in write(), which must not not sleep.
Reported-by: Dave Jones <davej@fedoraproject.org>
Tested-by: Dave Jones <davej@fedoraproject.org>
Cc: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix race in generic write implementation, which could lead to
temporarily degraded throughput.

The current generic write implementation introduced by commit
27c7acf2 ("USB: serial: reimplement generic fifo-based writes") has
always had this bug, although it's fairly hard to trigger and the
consequences are not likely to be noticed.

Specifically, a write() on one CPU while the completion handler is
running on another could result in only one of the two write urbs being
utilised to empty the remainder of the write fifo (unless there is a
second write() that doesn't race during that time).

Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just because it annoys me.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit bd27fa44 (usb: phy: generic:
Don't use regulator framework for RESET line) introduced regression: All
users of usb_nop_xceiv_register() will fail because there is no platform
data and the default reset GPIO is 0 which is a valid GPIO. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The musb driver is usable in host, gadget or dual role mode depending
on the kernel configuration.

However, the musb gadget part of the driver is enabling OTG mode
whether the driver is built for dual role or gadget only mode. This
induces a bug for gadget only USB device controllers where the kernel
tries to use Host Negotiation Protocol with such controllers, which
causes a panic.

This behaviour is now fixed by enabling OTG mode only when musb driver
is built for dual role mode.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In commit
88f718e3
"ARM: pxa: delete the custom GPIO header"
we removed the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h>.

The pxa25x_udc was not using that, but it was relying
on <linux/gpio.h> to implictly include <mach/gpio.h>
which in turn implicitly included <mach/hardware.h>,
which was needed for the driver to compile.

Fix this up by explicitly including the necessary
<mach/hardware.h> header.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves s3c_hsotg_disconnect function call from USBSusp interrupt
handler to SET_ADDRESS request handler.

It's because disconnected state can't be detected directly, because this
hardware doesn't support Disconnected interrupt for device mode. For both
Suspend and Disconnect events there is one interrupt USBSusp, but calling
s3c_hsotg_disconnect from this interrupt handler causes config reset in
composite layer, which is not undesirable for Suspended state.

For this reason s3c_hsotg_disconnect is called from SET_ADDRESS request
handler, which occurs always after disconnection, so we do disconnect
immediately before we are connected again. It's probably only way we
can do handle disconnection correctly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds missing spinlock locking in s3c_hsotg_complete_setup function,
and unlocking for gadget setup call.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

instead of having each user of generic phy find
out about its own resources and pass it to the
core layer, have th core layer itself figure that
out. It's as simple as moving a piece of code
around. This fixes a big regression caused during
the merge window where am335x-based platforms
wouldn't be able to probe their PHY driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit [4d175f34: usb: phy: nop: Defer clock prepare until PHY init]
removed a goto reaching behind a “return ret” at the end of the function
thus removing the only possible way that statement could be reached, and
so rendering it a dead code.  This commit cleans it up by removing said
dead code.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge tag 'ecryptfs-3.13-rc1-quiet-checkers' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull minor eCryptfs fix from Tyler Hicks:
 "Quiet static checkers by removing unneeded conditionals"

* tag 'ecryptfs-3.13-rc1-quiet-checkers' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: file->private_data is always valid

Pull second set of sound fixes from Takashi Iwai:
 "A collection of small fixes in HD-audio quirks and runtime PM, ASoC
  rcar, abs8500 and other codecs.  Most of commits are for stable
  kernels, too"

* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
  ALSA: hda - Provide missing pin configs for VAIO with ALC260
  ALSA: hda - Add headset quirk for Dell Inspiron 3135
  ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
  ALSA: hda - Fix missing bass speaker on ASUS N550
  ALSA: hda - Fix unbalanced runtime PM notification at resume
  ASoC: arizona: Set FLL to free-run before disabling
  ALSA: hda - A casual Dell Headset quirk
  ASoC: rcar: fixup dma_async_issue_pending() timing
  ASoC: rcar: off by one in rsnd_scu_set_route()
  ASoC: wm5110: Add post SYSCLK register patch for rev D chip
  ASoC: ab8500: Revert to using custom I/O functions
  ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
  ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
  ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
  ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
  ASoC: rcar: fixup mod access before checking

Pull DRM fixes from Dave Airlie:
 "I was going to leave this until post -rc1 but sysfs fixes broke
  hotplug in userspace, so I had to fix it harder, otherwise a set of
  pulls from intel, radeon and vmware,

  The vmware/ttm changes are bit larger but since its early and they are
  unlikely to break anything else I put them in, it lets vmware work
  with dri3"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
  drm/sysfs: fix hotplug regression since lifetime changes
  drm/exynos: g2d: fix memory leak to userptr
  drm/i915: Fix gen3 self-refresh watermarks
  drm/ttm: Remove set_need_resched from the ttm fault handler
  drm/ttm: Don't move non-existing data
  drm/radeon: hook up backlight functions for CI and KV family.
  drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
  drm/i915: Do not enable package C8 on unsupported hardware
  drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
  drm/i915: encoder->get_config is no longer optional
  drm/i915/tv: add ->get_config callback
  drm/radeon/cik: Add macrotile mode array query
  drm/radeon/cik: Return backend map information to userspace
  drm/vmwgfx: Make vmwgfx dma buffers prime aware
  drm/vmwgfx: Make surfaces prime-aware
  drm/vmwgfx: Hook up the prime ioctls
  drm/ttm: Add a minimal prime implementation for ttm base objects
  drm/vmwgfx: Fix false lockdep warning
  drm/ttm: Allow execbuf util reserves without ticket
  drm/i915: restore the early forcewake cleanup
  ...

Pull PCI updates from Bjorn Helgaas:
 "Miscellaneous
   - Remove duplicate disable from pcie_portdrv_remove() (Yinghai Lu)
   - Fix whitespace, capitalization, and spelling errors (Bjorn Helgaas)"

* tag 'pci-v3.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Remove duplicate pci_disable_device() from pcie_portdrv_remove()
  PCI: Fix whitespace, capitalization, and spelling errors

Pull SCSI target updates from Nicholas Bellinger:
 "Things have been quiet this round with mostly bugfixes, percpu
  conversions, and other minor iscsi-target conformance testing changes.

  The highlights include:

   - Add demo_mode_discovery attribute for iscsi-target (Thomas)
   - Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
   - Add send completion interrupt coalescing for ib_isert
   - Convert target-core to use percpu-refcounting for se_lun
   - Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
   - tcm_loop updates (Hannes)
   - target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)

  v3.14 is currently shaping to be a busy development cycle in target
  land, with initial support for T10 Referrals and T10 DIF currently on
  the roadmap"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
  iscsi-target: chap auth shouldn't match username with trailing garbage
  iscsi-target: fix extract_param to handle buffer length corner case
  iscsi-target: Expose default_erl as TPG attribute
  target_core_configfs: split up ALUA supported states
  target_core_alua: Make supported states configurable
  target_core_alua: Store supported ALUA states
  target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
  target_core_alua: spellcheck
  target core: rename (ex,im)plict -> (ex,im)plicit
  percpu-refcount: Add percpu-refcount.o to obj-y
  iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
  iscsi-target: Convert iscsi_session statistics to atomic_long_t
  target: Convert se_device statistics to atomic_long_t
  target: Fix delayed Task Aborted Status (TAS) handling bug
  iscsi-target: Reject unsupported multi PDU text command sequence
  ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
  iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
  target: Core does not need blkdev.h
  target: Pass through I/O topology for block backstores
  iser-target: Avoid using FRMR for single dma entry requests
  ...

Pull hwmon fixes from Guenter Roeck:
 - acpi_power_meter: Fix return value check from call to
   acpi_bus_get_device
 - nct6775: Fix/improve NCT6791 support
 - lm75: Add support for GMT G751

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (acpi_power_meter) Fix acpi_bus_get_device() return value check
  hwmon: (nct6775) NCT6791 supports weight control only for CPUFAN
  hwmon: (nct6775) Monitor additional temperature registers
  hwmon: (lm75) Add support for GMT G751 chip

Pull networking fixes from David Miller:

 1) Fix memory leaks and other issues in mwifiex driver, from Amitkumar
    Karwar.

 2) skb_segment() can choke on packets using frag lists, fix from
    Herbert Xu with help from Eric Dumazet and others.

 3) IPv4 output cached route instantiation properly handles races
    involving two threads trying to install the same route, but we
    forgot to propagate this logic to input routes as well.  Fix from
    Alexei Starovoitov.

 4) Put protections in place to make sure that recvmsg() paths never
    accidently copy uninitialized memory back into userspace and also
    make sure that we never try to use more that sockaddr_storage for
    building the on-kernel-stack copy of a sockaddr.  Fixes from Hannes
    Frederic Sowa.

 5) R8152 driver transmit flow bug fixes from Hayes Wang.

 6) Fix some minor fallouts from genetlink changes, from Johannes Berg
    and Michael Opdenacker.

 7) AF_PACKET sendmsg path can race with netdevice unregister notifier,
    fix by using RCU to make sure the network device doesn't go away
    from under us.  Fix from Daniel Borkmann.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  gso: handle new frag_list of frags GRO packets
  genetlink: fix genl_set_err() group ID
  genetlink: fix genlmsg_multicast() bug
  packet: fix use after free race in send path when dev is released
  xen-netback: stop the VIF thread before unbinding IRQs
  wimax: remove dead code
  net/phy: Add the autocross feature for forced links on VSC82x4
  net/phy: Add VSC8662 support
  net/phy: Add VSC8574 support
  net/phy: Add VSC8234 support
  net: add BUG_ON if kernel advertises msg_namelen > sizeof(struct sockaddr_storage)
  net: rework recvmsg handler msg_name and msg_namelen logic
  bridge: flush br's address entry in fdb when remove the
  net: core: Always propagate flag changes to interfaces
  ipv4: fix race in concurrent ip_route_input_slow()
  r8152: fix incorrect type in assignment
  r8152: support stopping/waking tx queue
  r8152: modify the tx flow
  r8152: fix tx/rx memory overflow
  netfilter: ebt_ip6: fix source and destination matching
  ...

Pull ARM fixes from Russell King:
 "Some small fixes for this merge window, most of them quite self
  explanatory - the biggest thing here is a fix for the ARMv7 LPAE
  suspend/resume support"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7894/1: kconfig: select GENERIC_CLOCKEVENTS if HAVE_ARM_ARCH_TIMER
  ARM: 7893/1: bitops: only emit .arch_extension mp if CONFIG_SMP
  ARM: 7892/1: Fix warning for V7M builds
  ARM: 7888/1: seccomp: not compatible with ARM OABI
  ARM: 7886/1: make OABI default to off
  ARM: 7885/1: Save/Restore 64-bit TTBR registers on LPAE suspend/resume
  ARM: 7884/1: mm: Fix ECC mem policy printk
  ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE
  ARM: 7882/1: mm: fix __phys_to_virt to work with 64 bit phys_addr_t in BE case
  ARM: 7881/1: __fixup_smp read of SCU config should do byteswap in BE case
  ARM: Fix nommu.c build warning

Pull KVM fixes from Gleb Natapov.

* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: kvm_clear_guest_page(): fix empty_zero_page usage
  kvm: mmu: delay mmu audit activation
  arm/arm64: KVM: Fix hyp mappings of vmalloc regions

Pull aio fixes from Benjamin LaHaise.

* git://git.kvack.org/~bcrl/aio-next:
  aio: nullify aio->ring_pages after freeing it
  aio: prevent double free in ioctx_alloc
  aio: Fix a trinity splat

Pull nfsd bugfixes from Bruce Fields:
 "A couple nfsd bugfixes"

* 'for-3.13' of git://linux-nfs.org/~bfields/linux:
  nfsd4: fix xdr decoding of large non-write compounds
  nfsd: make sure to balance get/put_write_access
  nfsd: split up nfsd_setattr

Pull GFS2 fixes from Steven Whitehouse:
 "A couple of small, but important bug fixes for GFS2.  The first one
  fixes a possible NULL pointer dereference, and the second one resolves
  a reference counting issue in one of the lesser used paths through
  atomic_open"

* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Fix ref count bug relating to atomic_open
  GFS2: fix potential NULL pointer dereference