Commit 8eba0eef ("at86rf230: remove irq_type in
request_irq") removed the trigger configuration when requesting an irq,
and instead relied on the interrupt trigger to be properly configured
already. This does not seem to be an assumption that can be safely made,
since boards disable all interrupt triggers on boot.

On these boards, force the irq to trigger on rising edge, which is also
the default for the chip.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/at803x.c:196:26-32: ERROR: application of sizeof to pointer

 sizeof when applied to a pointer typed expression gives the size of
 the pointer

Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single ported VF are currently not supported on configurations where
one or both ports are IB. When we hit this case, the relevant flow in
the driver didn't return error and jumped to the wrong label. Fix that.

Fixes: dd41cc3b ('net/mlx4: Adapt num_vfs/probed_vf params for single port VF')
Reported-by: Shirley Ma <shirley.ma@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It now takes up to 60 seconds to detect cable (un)plug on ADMtek Comet chips.
That's too slow and might cause people to think that it doesn't work at all.

Poll link status every 2 seconds instead of 60 for ADMtek Comet chips.
That should be fast enough while not stressing the system too much.

Tested with ADMtek AN983B.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Messages from the modem exceeding 256 bytes cause communication
failure.

The WDM protocol is strictly "read on demand", meaning that we only
poll for unread data after receiving a notification from the modem.
Since we have no way to know how much data the modem has to send,
we must make sure that the buffer we provide is "big enough".
Message truncation does not work. Truncated messages are left unread
until the modem has another message to send.  Which often won't
happen until the userspace application has given up waiting for the
final part of the last message, and therefore sends another command.

With a proper CDC WDM function there is a descriptor telling us
which buffer size the modem uses. But with this vendor specific
implementation there is no known way to calculate the exact "big
enough" number.  It is an unknown property of the modem firmware.
Experience has shown that 256 is too small.  The discussion of
this failure ended up concluding that 512 might be too small as
well. So 1024 seems like a reasonable value for now.

Fixes: 41c47d8c ("net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 629c9a8f (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior

In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.

Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Vrabel says:

====================
xen-netfront: fix resume regressions in 3.16-rc1

The introduction of multi-queue support to xen-netfront in 3.16-rc1,
broke resume/migration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When reconnecting to the backend (after a resume/migration, for example),
a different number of queues may be required (since the guest may have
moved to a different host with different capabilities).  During the
reconnection the old queues are torn down and new ones created.

Introduce xennet_create_queues() and xennet_destroy_queues() that fixes
three bugs during the reconnection.

- The old info->queues was leaked.
- The old queue's napi instances were not deleted.
- The new queue's napi instances were left disabled (which meant no
  packets could be received).

The xennet_destroy_queues() calls is deferred until the reconnection
instead of the disconnection (in xennet_disconnect_backend()) because
napi_disable() might sleep.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xennet_disconnect_backend() was not correctly iterating over all the
queues.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Mack says:

====================
Handle stuck TX queue bug in AT8030 PHY

These three small patches circument a hardware bug in AT8030 PHYs that
leads to stuck TX FIFO queues when the link goes away while there are
pending patches in der outbound queue. This bug has been confirmed by
the vendor, and their only proposed fix is to apply a hardware reset
every time the link goes down.

v1 -> v2:
	* Rename phy device callback from adjust_state to link_change_notify
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.

This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.

Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-06-18

Please pull this batch of fixes intended for the 3.16 stream!

For the Bluetooth bits, Gustavo says:

"This is our first batch of fixes for 3.16. Be aware that two patches here
are not exactly bugfixes:

* 71f28af57066 Bluetooth: Add clarifying comment for conn->auth_type
This commit just add some important security comments to the code, we found
it important enough to include it here for 3.16 since it is security related.

* 9f7ec8871132 Bluetooth: Refactor discovery stopping into its own function
This commit is just a refactor in a preparation for a fix in the next
commit (f8680f12).

All the other patches are fixes for deadlocks and for the Bluetooth protocols,
most of them related to authentication and encryption."

On top of that...

Chin-Ran Lo fixes a problems with overlapping DMA areas in mwifiex.

Michael Braun corrects a couple of issues in order to enable a new
device in rt2800usb.

Rafał Miłecki reverts a b43 patch that caused a regression, fixes a
Kconfig typo, and corrects a frequency reporting error with the G-PHY.

Stanislaw Grsuzka fixes an rfkill regression for rt2500pci, and avoids
a rt2x00 scheduling while atomic BUG.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When writing to the sysctl field net.sctp.auth_enable, it can well
be that the user buffer we handed over to proc_dointvec() via
proc_sctp_do_auth() handler contains something other than integers.

In that case, we would set an uninitialized 4-byte value from the
stack to net->sctp.auth_enable that can be leaked back when reading
the sysctl variable, and it can unintentionally turn auth_enable
on/off based on the stack content since auth_enable is interpreted
as a boolean.

Fix it up by making sure proc_dointvec() returned sucessfully.

Fixes: b14878cc ("net: sctp: cache auth_enable per endpoint")
Reported-by: Florian Westphal <fwestpha@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d3f6f3a1 ("tg3: Prevent page
allocation failure during TSO workaround") modified driver logic
to use tg3_tso_bug() for any TSO fragment that hits hardware bug
conditions thus the patch increased the scope of work for tg3_tso_bug()
to cover devices that support NETIF_F_TSO6 as well. Prior to the
patch, tg3_tso_bug() would only be used on devices supporting
NETIF_F_TSO.

A regression was introduced for IPv6 packets requiring the workaround.
To properly perform GSO on SKBs with TCPV6 gso_type, we need to call
skb_gso_segment() with NETIF_F_TSO6 feature flag cleared, or the
function will return NULL and cause a kernel oops as tg3 is not handling
a NULL return value. This patch fixes the problem.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there is an MSS change (or misbehaving receiver) that causes a SACK
to arrive that covers the end of an skb but is less than one MSS, then
tcp_match_skb_to_sack() was rounding up pkt_len to the full length of
the skb ("Round if necessary..."), then chopping all bytes off the skb
and creating a zero-byte skb in the write queue.

This was visible now because the recently simplified TLP logic in
bef1909e ("tcp: fixing TLP's FIN recovery") could find that 0-byte
skb at the end of the write queue, and now that we do not check that
skb's length we could send it as a TLP probe.

Consider the following example scenario:

 mss: 1000
 skb: seq: 0 end_seq: 4000  len: 4000
 SACK: start_seq: 3999 end_seq: 4000

The tcp_match_skb_to_sack() code will compute:

 in_sack = false
 pkt_len = start_seq - TCP_SKB_CB(skb)->seq = 3999 - 0 = 3999
 new_len = (pkt_len / mss) * mss = (3999/1000)*1000 = 3000
 new_len += mss = 4000

Previously we would find the new_len > skb->len check failing, so we
would fall through and set pkt_len = new_len = 4000 and chop off
pkt_len of 4000 from the 4000-byte skb, leaving a 0-byte segment
afterward in the write queue.

With this new commit, we notice that the new new_len >= skb->len check
succeeds, so that we return without trying to fragment.

Fixes: adb92db8 ("tcp: Make SACK code to split only at mss boundaries")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit d36a4f4b.
Signed-off-by: David S. Miller <davem@davemloft.net>

The original checks (via sk_chk_filter) for instruction count uses ">",
not ">=", so changing this in sk_convert_filter has the potential to break
existing seccomp filters that used exactly BPF_MAXINSNS many instructions.

Fixes: bd4cf0ed ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sysctl handler proc_sctp_do_hmac_alg(), proc_sctp_do_rto_min() and
proc_sctp_do_rto_max() do not properly reflect some error cases
when writing values via sysctl from internal proc functions such
as proc_dointvec() and proc_dostring().

In all these cases we pass the test for write != 0 and partially
do additional work just to notice that additional sanity checks
fail and we return with hard-coded -EINVAL while proc_do*
functions might also return different errors. So fix this up by
simply testing a successful return of proc_do* right after
calling it.

This also allows to propagate its return value onwards to the user.
While touching this, also fix up some minor style issues.

Fixes: 4f3fdf3b ("sctp: add check rto_min and rto_max in sysctl")
Fixes: 3c68198e ("sctp: Make hmac algorithm selection for cookie generation dynamic")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return the actual error code if call kset_create_and_add() failed

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the underlying device supports TCP offloads for VXLAN/UDP
encapulated traffic, we need to reflect that through the hw_enc_features
field of the bonding net-device. This will cause the xmit path
in the core networking stack to provide bonding with encapsulated
GSO frames to offload into the HW etc.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added FUJITSU SIEMENS A8NE-FM to the list of 32bit DMA boards

>From Tomi O.:
After I added an entry to this MB into the skge.c
driver in order to enable the mentioned 64bit dma disable quirk,
the network data corruptions ended and everything is fine again.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
netfilter fixes for net

The following patchset contains netfilter updates for your net tree,
they are:

1) Fix refcount leak when dumping the dying/unconfirmed conntrack lists,
   from Florian Westphal.

2) Fix crash in NAT when removing a netnamespace, also from Florian.

3) Fix a crash in IPVS when trying to remove an estimator out of the
   sysctl scope, from Julian Anastasov.

4) Add zone attribute to the routing to calculate the message size in
   ctnetlink events, from Ken-ichirou MATSUZAWA.

5) Another fix for the dying/unconfirmed list which was preventing to
   dump more than one memory page of entries (~17 entries in x86_64).

6) Fix missing RCU-safe list insertion in the rule replacement code
   in nf_tables.

7) Since the new transaction infrastructure is in place, we have to
   upgrade the chain use counter from u16 to u32 to avoid overflow
   after more than 2^16 rules are added.

8) Fix refcount leak when replacing rule in nf_tables. This problem
   was also introduced in new transaction.

9) Call the ->destroy() callback when releasing nft-xt rules to fix
   module refcount leaks.

10) Set the family in the netlink messages that contain set elements
    in nf_tables to make it consistent with other object types.

11) Don't dump NAT port information if it is unset in nft_nat.

12) Update the MAINTAINERS file, I have merged the ebtables entry
    into netfilter. While at it, also removed the netfilter users
    mailing list, the development list should be enough.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Moreover, remove reference to the netfilter users mailing list,
so they don't receive patches.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The commit 96c50caa (net: fec: Enable IP header hardware checksum)
enable HW IP header checksum for IPV4 and IPV6, which causes IPV6 TCP/UDP
cannot work. (The issue is reported by Russell King)

For FEC IP header checksum function: Insert IP header checksum. This "IINS"
bit is written by the user. If set, IP accelerator calculates the IP header
checksum and overwrites the IINS corresponding header field with the calculated
value. The checksum field must be cleared by user, otherwise the checksum
always is 0xFFFF.

So the previous patch clear IP header checksum field regardless of IP frame
type.

In fact, IP HW detect the packet as IPV6 type, even if the "IINS" bit is set,
the IP accelerator is not triggered to calculates IPV6 header checksum because
IPV6 frame format don't have checksum.

So this results in the IPV6 frame being corrupted.

The patch just add software detect the current packet type, if it is IPV6
frame, it don't clear IP header checksum field.

Cc: Russell King <linux@arm.linux.org.uk>
Reported-and-tested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ptp_pch driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As reported by Niels, starting rfkill polling during device probe
(commit e2bc7c5f, generally sane change) broke rfkill on rt2500pci
device. I considered that bug as some initalization issue, which
should be fixed on rt2500pci specific code. But after several
attempts (see bug report for details) we fail to find working solution.
Hence I decided to revert to old behaviour on rt2500pci to fix
regression.

Additionally patch also unregister rfkill on device remove instead
of ifconfig down, what was another issue introduced by bad commit.

Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=73821

Fixes: e2bc7c5f ("rt2x00: Fix rfkill_polling register function.")
Cc: stable@vger.kernel.org
Bisected-by: Niels <nille0386@googlemail.com>
Reported-and-tested-by: Niels <nille0386@googlemail.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Support for firmware rev 508+ was added years ago, but we never noticed
it reports channel in a different way for G-PHY devices. Instead of
offset from 2400 MHz it simply passes channel id (AKA hw_value).

So far it was (most probably) affecting monitor mode users only, but
the following recent commit made it noticeable for quite everybody:

commit 3afc2167
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Tue Mar 4 16:50:13 2014 +0200

    cfg80211/mac80211: ignore signal if the frame was heard on wrong channel
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The device 057c:8501 (AVM Fritz! WLAN v2 rev. B) boots into a state that does
not actually require loading a firmware file. The vendors driver finds out
about this by checking a firmware state register, so this patch adds this here.

Finally, with this patch applied, my wifi dongle actually becomes
useful (scan + connect to wpa network works).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The device 057c:8501 (AVM Fritz! WLAN v2 rev. B) currently does not
load. One thing observed is that the vendors driver detects EFUSE mode
for this device, but rt2800usb does not. This is due to rt2800usb
lacking a check for the firmware mode present in the vendors driver,
that this patch adopts for rt2800usb.

With this patch applied, the 'RF chipset' detection does no longer fail.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

c25aaf81: "hyperv: Enable sendbuf mechanism on the send path" added
some teardown code that looks like it was copied from the recieve path
above, but missed a variable name replacement.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This variable is overwritten by the child socket assignment before
it ever gets used.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'i' is unused in tile_net_dev_init() after commit d581ebf5
("net: tile: Use helpers from linux/etherdevice.h to check/set MAC").
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clock_adjtime was included in glibc 2.14. _GNU_SOURCE must be defined
to make it available.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 2 HISAX_AVM_A1_PCMCIA Kconfig entries. The kbuild system
ignores the second one, and apparently nobody noticed the problem so
far, so let's remove that second entry.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first half of the HiSax config options is presented if
ISDN_DRV_HISAX!=n, while the second half of the options is presented
if ISDN_DRV_HISAX. That's the same, so merge both conditionals.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>