According to the ssm2603 data sheet (control register sequencing), the
digital core should be activated only after all necessary bits in the
power register are enabled, and a delay determined by the decoupling
capacitor on the VMID pin has passed. If the digital core is activated
too early, or even before the ADC is powered up, audible artifacts
appear at the beginning of the recorded signal.

The digital core is also needed for playback, so when recording starts
it may already be enabled. This means we cannot get the power sequence
correct when we want to be able to start recording after playback.

As a workaround put the MIC mute switch into the DAPM routes. This
way we can keep the recording disabled until the MIC Bias has settled
and thus get rid of audible artifacts.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
m.felsch@pengutronix.de: adapt commit message
m.felsch@pengutronix.de: drop of configuration as mentioned by Mark:
			 https://patchwork.kernel.org/patch/10407449/Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

DAIs linked to the dummy will not have an associated playback/capture
widget, so we need to skip the update in that case.

Fixes: 078a85f2 ("ASoC: dapm: Only power up active channels from a DAI")
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This driver use the gpio consumer interface.
Add the header as it's needed.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is a spelling mistake in a dev_warn message. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

soc_tplg_link_config() will find the physical dai link and call
soc_tplg_dai_link_load() to load the BE dai link. Currently remove_link()
is only used to remove the FE dai link which is created by the topology.
The BE dai link cannot however be unloaded in snd_soc_tplg_component
_remove(), which is problematic if anything needs to be released or
reinitialized.

This patch aligns the definitions of dynamic types with the existing
UAPI and adds a new remove_backend_link() routine to unload the the BE
dai link when snd_soc_tplg_component_remove() is invoked.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Originally snd_soc_init_platform was not cleaning up its pointers, this
was fixed to always reallocate dynamic memory but created a memory leak
when snd_soc_init_platform was called multiple times during the same
probe attempt and also threw away any changes made to the struct between
calls. In order to avoid reallocating memory that is still valid, the
behaviour will be changed to clear the dynamically set pointers on a
probe error and a unregister event and snd_soc_init_platform will go
back to its original behaviour of only allocating null pointers so it will
stop throwing away valid changes.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Wen Yang <yellowriver2010@hotmil.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently, in some complex cases, more than one widgets have same
name and registed from differnt dapm context, and route add from
another context too. When snd_soc_dapm_add_route, the previous
registered widget will overwritten by the latest same name widget,
will cause unexpect error. For Asoc framework we cant avoid this
situation and we cant decide which widget that wanted with route.
At least we can give users a notice.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently all widgets attached to a DAI link will be powered
up when the DAI is active, however this may include routes
that are not actually in use if there are unused channels
available on the DAI.

The macros for creating AIF widgets already include an entry for
slot, it is proposed to change that to channel. The effective
difference here being respresenting the logical channel index
rather than the physical slot index. The CODECs currently
using the slot entry on the DAPM_AIF macros are using it in
a manner consistent with this, the CODECs not using it just
have the field set to zero.

A variable is added to snd_soc_dapm_widget to represent
this channel index and then for each AIF widget attached to
a DAI this is compared against the number of channels on
the stream. Enabling the links for those which will be in
use. This has the nice property that the CODECs which haven't
used the slot/channel entry in the macro will function exactly
as before due to all the AIF widgets having a channel of zero
and a stream by definition having at least one channel.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 7620fe91 ("ASoC: topology: fix memory leak in
soc_tplg_dapm_widget_create") fixed a memory leak issue, but
additional tests and KASAN reports show a use-after-free in soc-dapm.

The widgets are created with a kmemdup operating on a template. The
"name" string is also duplicated, but the "sname" string is not. As a
result, when the template is freed after widget creation, its sname
string is still used.

Fix by explicitly duplicating the "sname" string, and freeing it when
required.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The driver function for transferring/receiving
BT encoded data to/from BT firmware.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

document for btcvsd driver
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Set the channel number on each AIF widget to allow unused channels not
to be powered up across AIFs.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Renesas sound card need to judge that whether it is using
"TDM Split mode". To judge it and for other purpose, it has
rsnd_parse_connect_simple() and rsnd_parse_connect_graph(),
but these are using different judgement policy for
TDM Split mode.
It is pointless and confusable.
This patch add new rsnd_parse_tdm_split_mode() and use common
judgement policy for simple-card/audio-graph.

Without this patch, CTU will be judged as TDM Split mode
on audio-graph card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Current rsnd driver has below function to check connection
	rsnd_parse_connect_simple()
	rsnd_parse_connect_graph()
But these have different parameters. This patch synchronize these
for cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Spreadtrum DMA engine uses the link-list mode to support audio playback
or capture, thus this patch adds audio DMA platform support for CPU DAI to
trigger DMA link-list transfer.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add documentation for Spreadtrum DMA platform driver.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

struct snd_soc_dapm_route has been modified to be a dynamic
object so that it can be used to save driver specific
data while parsing topology and clean up
driver-specific data during driver unloading.

This patch makes the following changes to accomplish the above:
1. Set the dobj member of snd_soc_dapm_route during the
SOC_TPLG_PASS_GRAPH pass of topology parsing.
2. Add the remove_route() routine that will be called while
removing all dynamic objects from the component driver.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add a new dobj type SND_SOC_DOBJ_GRAPH for dapm routes
and add snd_soc_dobj member to struct snd_soc_dapm_route.
This enables device drivers to save driver specific
data pertaining to dapm routes and also be able
to clean up the data when the driver module is unloaded.

Also, reorder the snd_soc_dobj_type types to align with
matching topology header types.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

template.sname and template.name are only freed when an error occur.
They should be freed in the success return case, too.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

dtexts is two dimensional array, so we also need to free it after
freeing its fields.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently when we unload and reload machine driver few times we end with
corrupted list and try to cleanup no longer existing objects. Fix this
by removing dobj from the list.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We already have passed dobj, there is no reason to access it through
containing structs.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

For some reason we test if the machine is passed as a parameter before
fixing up the codec name. This is unnecessary, generates false
positives in static analysis tools and done only in this machine
driver, remove and adjust indentation.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add a codec driver to control ChromeOS EC codec.

Use EC Host command to enable/disable I2S recording and control other
configurations.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add documentation for Chrome EC codec driver.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.0-rc4

Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds audio routing for both playback and capture.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds required dapm widgets for capture path.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds required dapm widgets for playback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds basic controls found in wcd9335 codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

CLASS-H controller/Amplifier is common accorss Qualcomm WCD codec series.
This patchset adds basic CLASS-H controller apis for WCD codecs after
wcd9335 to use.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC,
It supports both I2S/I2C and SLIMbus audio interfaces.
On slimbus interface it supports two data lanes; 16 Tx ports
and 8 Rx ports. It has Seven DACs and nine dedicated interpolators,
Seven (six audio ADCs, and one VBAT ADC), Multibutton headset
control (MBHC), Active noise cancellation and Sidetone paths
and processing.

This patchset adds very basic support for playback and capture
via the 9 interpolators and ADC respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch updates wcd9335 bindings with recommended properties.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>