- 11 Jul, 2014 5 commits
-
-
Paolo Bonzini authored
For the next patch we will need to know the full state of the interrupt shadow; we will then set KVM_REQ_EVENT when one bit is cleared. However, right now get_interrupt_shadow only returns the one corresponding to the emulated instruction, or an unconditional 0 if the emulated instruction does not have an interrupt shadow. This is confusing and does not allow us to check for cleared bits as mentioned above. Clean the callback up, and modify toggle_interruptibility to match the comment above the call. As a small result, the call to set_interrupt_shadow will be skipped in the common case where int_shadow == 0 && mask == 0. Signed-off-by:Paolo Bonzini <pbonzini@redhat.com>
-
Paolo Bonzini authored
About 25% of the time spent in emulation of invalid guest state is wasted in checking whether emulation is required for the next instruction. However, this almost never changes except when a segment register (or TR or LDTR) changes, or when there is a mode transition (i.e. CR0 changes). In fact, vmx_set_segment and vmx_set_cr0 already modify vmx->emulation_required (except that the former for some reason uses |= instead of just an assignment). So there is no need to call guest_state_valid in the emulation loop. Emulation performance test results indicate 1650-2600 cycles for common instructions, versus 2300-3200 before this patch on a Sandy Bridge Xeon. Signed-off-by: -
Matthias Lange authored
Since commit 575203 the MCE subsystem in the Linux kernel for AMD sets bit 18 in MSR_K7_HWCR. Running such a kernel as a guest in KVM on an AMD host results in a GPE injected into the guest because kvm_set_msr_common returns 1. This patch fixes this by masking bit 18 from the MSR value desired by the guest. Signed-off-by:
Matthias Lange <matthias.lange@kernkonzept.com> Signed-off-by:
-
Nadav Amit authored
We encountered a scenario in which after an INIT is delivered, a pending interrupt is delivered, although it was sent before the INIT. As the SDM states in section 10.4.7.1, the ISR and the IRR should be cleared after INIT as KVM does. This also means that pending interrupts should be cleared. This patch clears upon reset (and INIT) the pending interrupts; and at the same occassion clears the pending exceptions, since they may cause a similar issue. Signed-off-by:
Nadav Amit <namit@cs.technion.ac.il> Signed-off-by:
-
Jim Mattson authored
We have noticed that qemu-kvm hangs early in the BIOS when runnning nested under some versions of VMware ESXi. The problem we believe is because KVM assumes that the platform preserves the 'G' but for any segment register. The SVM specification itemizes the segment attribute bits that are observed by the CPU, but the (G)ranularity bit is not one of the bits itemized, for any segment. Though current AMD CPUs keep track of the (G)ranularity bit for all segment registers other than CS, the specification does not require it. VMware's virtual CPU may not track the (G)ranularity bit for any segment register. Since kvm already synthesizes the (G)ranularity bit for the CS segment. It should do so for all segments. The patch below does that, and helps get rid of the hangs. Patch applies on top of Linus' tree. Signed-off-by:
Jim Mattson <jmattson@vmware.com> Signed-off-by:
Alok N Kataria <akataria@vmware.com> Signed-off-by:
-
- 09 Jul, 2014 9 commits
-
-
James Hogan authored
Document the MIPS specific parts of the KVM API, including: - The layout of the kvm_regs structure. - The interrupt number passed to KVM_INTERRUPT. - The registers supported by the KVM_{GET,SET}_ONE_REG interface, and the encoding of those register ids. - That KVM_INTERRUPT and KVM_GET_REG_LIST are supported on MIPS. Signed-off-by:James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: kvm@vger.kernel.org Cc: Randy Dunlap <rdunlap@infradead.org> Cc: linux-doc@vger.kernel.org Signed-off-by:
-
James Hogan authored
Some of the MIPS registers that can be accessed with the KVM_{GET,SET}_ONE_REG interface have fairly long names, so widen the Register column of the table in the KVM_SET_ONE_REG documentation to allow them to fit. Tabs in the table are replaced with spaces at the same time for consistency. Signed-off-by: -
James Hogan authored
KVM_SET_SIGNAL_MASK is implemented in generic code and isn't x86 specific, so document it as being applicable for all architectures. Signed-off-by:
-
Nadav Amit authored
In two cases lapic.c does not use the apic_debug macro correctly. This patch fixes them. Signed-off-by:
-
Tomasz Grabiec authored
I've observed kvmclock being marked as unstable on a modern single-socket system with a stable TSC and qemu-1.6.2 or qemu-2.0.0. The culprit was failure in TSC matching because of overflow of kvm_arch::nr_vcpus_matched_tsc in case there were multiple TSC writes in a single synchronization cycle. Turns out that qemu does multiple TSC writes during init, below is the evidence of that (qemu-2.0.0): The first one: 0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel] 0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm] 0xffffffffa04cfd6b : kvm_arch_vcpu_postcreate+0x4b/0x80 [kvm] 0xffffffffa04b8188 : kvm_vm_ioctl+0x418/0x750 [kvm] The second one: 0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel] 0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm] 0xffffffffa090610d : vmx_set_msr+0x29d/0x350 [kvm_intel] 0xffffffffa04be83b : do_set_msr+0x3b/0x60 [kvm] 0xffffffffa04c10a8 : msr_io+0xc8/0x160 [kvm] 0xffffffffa04caeb6 : kvm_arch_vcpu_ioctl+0xc86/0x1060 [kvm] 0xffffffffa04b6797 : kvm_vcpu_ioctl+0xc7/0x5a0 [kvm] #0 kvm_vcpu_ioctl at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1780 #1 kvm_put_msrs at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1270 #2 kvm_arch_put_registers at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1909 #3 kvm_cpu_synchronize_post_init at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1641 #4 cpu_synchronize_post_init at /build/buildd/qemu-2.0.0+dfsg/include/sysemu/kvm.h:330 #5 cpu_synchronize_all_post_init () at /build/buildd/qemu-2.0.0+dfsg/cpus.c:521 #6 main at /build/buildd/qemu-2.0.0+dfsg/vl.c:4390 The third one: 0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel] 0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm] 0xffffffffa090610d : vmx_set_msr+0x29d/0x350 [kvm_intel] 0xffffffffa04be83b : do_set_msr+0x3b/0x60 [kvm] 0xffffffffa04c10a8 : msr_io+0xc8/0x160 [kvm] 0xffffffffa04caeb6 : kvm_arch_vcpu_ioctl+0xc86/0x1060 [kvm] 0xffffffffa04b6797 : kvm_vcpu_ioctl+0xc7/0x5a0 [kvm] #0 kvm_vcpu_ioctl at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1780 #1 kvm_put_msrs at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1270 #2 kvm_arch_put_registers at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1909 #3 kvm_cpu_synchronize_post_reset at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1635 #4 cpu_synchronize_post_reset at /build/buildd/qemu-2.0.0+dfsg/include/sysemu/kvm.h:323 #5 cpu_synchronize_all_post_reset () at /build/buildd/qemu-2.0.0+dfsg/cpus.c:512 #6 main at /build/buildd/qemu-2.0.0+dfsg/vl.c:4482 The fix is to count each vCPU only once when matched, so that nr_vcpus_matched_tsc holds the size of the matched set. This is achieved by reusing generation counters. Every vCPU with this_tsc_generation == cur_tsc_generation is in the matched set. The match set is cleared by setting cur_tsc_generation to a value which no other vCPU is set to (by incrementing it). I needed to bump up the counter size form u8 to u64 to ensure it never overflows. Otherwise in cases TSC is not written the same number of times on each vCPU the counter could overflow and incorrectly indicate some vCPUs as being in the matched set. This scenario seems unlikely but I'm not sure if it can be disregarded. Signed-off-by:
Tomasz Grabiec <tgrabiec@cloudius-systems.com> Signed-off-by:
-
Jan Kiszka authored
Obtaining the port number from DX is bogus as a) there are immediate port accesses and b) user space may have changed the register content while processing the PIO access. Forward the correct value from the instruction emulator instead. Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by:
-
Jan Kiszka authored
The access size of an in/ins is reported in dst_bytes, and that of out/outs in src_bytes. Signed-off-by:
-
Jan Kiszka authored
First, kvm_read_guest returns 0 on success. And then we need to take the access size into account when testing the bitmap: intercept if any of bits corresponding to the access is set. Signed-off-by:
-
Jan Kiszka authored
CLTS only changes TS which is not monitored by selected CR0 interception. So skip any attempt to translate WRITE_CR0 to CR0_SEL_WRITE for this instruction. Signed-off-by:
-
- 30 Jun, 2014 11 commits
-
-
Rickard Strandqvist authored
A struct member variable is set to the same value more than once This was found using a static code analysis program called cppcheck. Signed-off-by:
Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by:
-
Deng-Cheng Zhu authored
It's impossible to fall into the error handling of the TLB index after being masked by (KVM_MIPS_GUEST_TLB_SIZE - 1). Remove the dead code. Reported-by:
Deng-Cheng Zhu <dengcheng.zhu@imgtec.com> Reviewed-by:
-
Deng-Cheng Zhu authored
The commpage is allocated using kzalloc(), so there's no need of cleaning the memory of the kvm_mips_commpage struct and its internal mips_coproc. Reviewed-by:
-
Deng-Cheng Zhu authored
Since all the files are in arch/mips/kvm/, there's no need of the prefixes "kvm_" and "kvm_mips_". Reviewed-by:
-
Deng-Cheng Zhu authored
The keyword volatile for idx in the TLB functions is unnecessary. Reviewed-by:
-
Deng-Cheng Zhu authored
No logic changes inside. Reviewed-by:
-
Deng-Cheng Zhu authored
Replace printks with kvm_[err|info|debug]. Signed-off-by:
-
Deng-Cheng Zhu authored
No logic changes inside. Signed-off-by:
-
Paolo Bonzini authored
Merge tag 'kvms390-20140626' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD Fix sie.h header related problems introduced during the 3.16 development cycle.
-
Paolo Bonzini authored
Fix bad x86 regression introduced during merge window.
-
Jan Kiszka authored
We import the CPL via SS.DPL since ae9fedc7. However, we fail to export it this way so far. This caused spurious guest crashes, e.g. of Linux when accessing the vmport from guest user space which triggered register saving/restoring to/from host user space. Signed-off-by:
-
- 26 Jun, 2014 1 commit
-
-
Heiko Carstens authored
sie.h was missing in arch/s390/include/uapi/asm/Kbuild and therefore missed the "make headers_check" target. If added it reveals that also arch/s390/include/asm/sigp.h would become uapi. This is something we certainly do not want. So remove that dependency as well. The header file was merged with ceae283b "KVM: s390: add sie exit reasons tables", therefore we never had a kernel release with this commit and can still change anything. Acked-by:
Alexander Yarygin <yarygin@linux.vnet.ibm.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Cornelia Huck <cornelia.huck@de.ibm.com>
-
- 19 Jun, 2014 14 commits
-
-
Nadav Amit authored
VMX instructions use 32-bit operands in 32-bit mode, and 64-bit operands in 64-bit mode. The current implementation is broken since it does not use the register operands correctly, and always uses 64-bit for reads and writes. Moreover, write to memory in vmwrite only considers long-mode, so it ignores cs.l. This patch fixes this behavior. Signed-off-by:
-
Nadav Amit authored
On 32-bit mode only bits [31:0] of the CR should be used for setting the CR value. Otherwise, the host may incorrectly assume the value is invalid if bits [63:32] are not zero. Moreover, the CR is currently being read twice when CR8 is used. Last, nested mov-cr exiting is modified to handle the CR value correctly as well. Signed-off-by:
-
Nadav Amit authored
Currently, the hypercall handling routine only considers LME as an indication to whether the guest uses 32/64-bit mode. This is incosistent with hyperv hypercalls handling and against the common sense of considering cs.l as well. This patch uses is_64_bit_mode instead of is_long_mode for that matter. In addition, the result is masked in respect to the guest execution mode. Last, it changes kvm_hv_hypercall to use is_64_bit_mode as well to simplify the code. Signed-off-by:
-
Nadav Amit authored
When the guest sets DR6 and DR7, KVM asserts the high 32-bits are clear, and otherwise injects a #GP exception. This exception should only be injected only if running in long-mode. Signed-off-by:
-
Jan Kiszka authored
Many real CPUs get this wrong as well, but ours is totally off: bits 9:1 define the highest index value. Signed-off-by:
-
Jan Kiszka authored
Allow L1 to "leak" its debug controls into L2, i.e. permit cleared VM_{ENTRY_LOAD,EXIT_SAVE}_DEBUG_CONTROLS. This requires to manually transfer the state of DR7 and IA32_DEBUGCTLMSR from L1 into L2 as both run on different VMCS. Signed-off-by: -
Jan Kiszka authored
SDM says bits 1, 4-6, 8, 13-16, and 26 have to be set. Signed-off-by:
-
Jan Kiszka authored
We already have this control enabled by exposing a broken MSR_IA32_VMX_PROCBASED_CTLS value. This will properly advertise our capability once the value is fixed by clearing the right bits in MSR_IA32_VMX_TRUE_PROCBASED_CTLS. We also have to ensure to test the right value on L2 entry. Signed-off-by:
-
Jan Kiszka authored
We already implemented them but failed to advertise them. Currently they all return the identical values to the capability MSRs they are augmenting. So there is no change in exposed features yet. Drop related comments at this chance that are partially incorrect and redundant anyway. Signed-off-by:
-
Jan Kiszka authored
The spec says those controls are at bit position 2 - makes 4 as value. The impact of this mistake is effectively zero as we only use them to ensure that these features are set at position 2 (or, previously, 1) in MSR_IA32_VMX_{EXIT,ENTRY}_CTLS - which is and will be always true according to the spec. Signed-off-by: -
Nadav Amit authored
On long-mode the current NOP (0x90) emulation still writes back to RAX. As a result, EAX is zero-extended and the high 32-bits of RAX are cleared. Signed-off-by:
-
Nadav Amit authored
Even if the condition of cmov is not satisfied, bits[63:32] should be cleared. This is clearly stated in Intel's CMOVcc documentation. The solution is to reassign the destination onto itself if the condition is unsatisfied. For that matter the original destination value needs to be read. Signed-off-by:
-
Nadav Amit authored
Return unhandlable error on inter-privilege level ret instruction. This is since the current emulation does not check the privilege level correctly when loading the CS, and does not pop RSP/SS as needed. Cc: stable@vger.kernel.org Signed-off-by:
-
Nadav Amit authored
The emulator does not emulate the xadd instruction correctly if the two operands are the same. In this (unlikely) situation the result should be the sum of X and X (2X) when it is currently X. The solution is to first perform writeback to the source, before writing to the destination. The only instruction which should be affected is xadd, as the other instructions that perform writeback to the source use the extended accumlator (e.g., RAX:RDX). Signed-off-by:
-
