- 26 Feb, 2010 40 commits
-
-
Hans de Goede authored
Streaming of VGA stv0680 based cams (instead of CIF ones) failed, because we were using the wrong control pipe for certain commands, this patch fixes this. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans de Goede authored
Mark led on eyetoy II as inverted, I have the feeling the led needs to be inverted for all 519 based cams (iow we got the set led code wrong), but lets just deal with this one cam at a time to avoid breaking currently working cams. Signed-off-by:
-
Hans de Goede authored
stv0680 cameras currently only work when already plugged in when the system boots (or when manually re-loading the driver after boot). This patch fixes this. Signed-off-by:
-
Theodore Kilgore authored
gspca.txt: add cams supported by mr97310a, sq905(c) and sn9c2028 drivers Signed-off-by:
Theodore Kilgore <kilgota@banach.math.auburn.edu> Signed-off-by:
-
Theodore Kilgore authored
New gspca subdriver adding support for SN9C2028 dual-mode cameras. Signed-off-by:
-
Theodore Kilgore authored
If you read the mail to Oliver Neukum on the linux-usb list, then you know that I found a cure for the mysterious problem that the MR97310a CIF "type 1" cameras have been freezing up and refusing to stream if hooked up to a machine with a UHCI controller. Namely, the cure is that if the camera is an mr97310a CIF type 1 camera, you have to send it 0xa0, 0x00. Somehow, this is a timing reset command, or such. It un-blocks whatever was previously stopping the CIF type 1 cameras from working on the UHCI-based machines. Signed-off-by:
Theodore Kilgore <kilgota@auburn.edu> Signed-off-by:
-
Arvo Järve authored
The TDA8261 driver would crash when reading more than a byte as described. ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff [ 8.430350] KNC1-2: MAC addr = 00:09:d6:65:2d:91 [ 8.610008] saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer [ 8.734457] stb0899_attach: Attaching STB0899 [ 8.768481] tda8261_attach: Attaching TDA8261 8PSK/QPSK tuner [ 8.768485] DVB: registering adapter 2 frontend 0 (STB0899 Multistandard)... Once I launch scan-s2: scan-s2 -vvvv -a 2 -s 1 -l UNIVERSAL /usr/share/dvb/dvb-s/Hotbird-13.0E I see the following via dmesg: [ 435.040017] saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer [ 435.778648] tda8261_get_bandwidth: Bandwidth=40000000 [ 435.781781] tda8261_get_bandwidth: Bandwidth=40000000 [ 435.783311] tda8261_set_state: Step size=1, Divider=1000, PG=0x793 (1939) [ 435.783512] tda8261_set_state: Waiting to Phase LOCK [ 435.810134] tda8261_get_status: Tuner Phase Locked [ 435.810137] tda8261_set_state: Tuner Phase locked: status=1 [ 435.810139] tda8261_set_frequency: Frequency=1939000 [ 435.810141] tda8261_get_frequency: Frequency=7574 [ 435.830008] tda8261_get_bandwidth: Bandwidth=40000000 [ 436.402814] tda8261_get_bandwidth: Bandwidth=40000000 [ 436.405946] tda8261_get_bandwidth: Bandwidth=40000000 [ 436.407458] general protection fault: 0000 [#1] SMP [ 436.407527] last sysfs file: /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor [ 436.407560] CPU 0 [ 436.407601] Modules linked in: tda8261 stb0899 dvb_pll mt352 lnbp21 budget_av saa7146_vv snd_hda_codec_realtek videodev stv0299 v4l1_compat coretemp snd_hda_intel v4l2_compat_ioctl32 i915 videobuf_dma_sg b2c2_flexcop_pci snd_hda_codec budget_ci videobuf_core b2c2_flexcop ir_common w83627ehf drm snd_hwdep cx24123 budget_core hwmon_vid snd_pcm cx24113 dvb_core iptable_filter snd_timer i2c_algo_bit ip_tables saa7146 s5h1420 snd ttpci_eeprom soundcore intel_agp video serio_raw pcspkr lp snd_page_alloc x_tables output parport pata_it8213 e1000e [ 436.408757] Pid: 1410, comm: kdvb-ad-2-fe-0 Not tainted 2.6.31-14-server #48-Ubuntu C2SBC-Q [ 436.408818] RIP: 0010:[<ffffffffa00241a1>] [<ffffffffa00241a1>] tda8261_set_state+0x51/0x250 [tda8261] [ 436.408903] RSP: 0018:ffff88013649bc70 EFLAGS: 00010283 [ 436.408945] RAX: 00000000000f1748 RBX: ffff880138870680 RCX: 0000000000000018 [ 436.408990] RDX: ffff88013649bcd0 RSI: 0000000000000001 RDI: ffff880135273010 [ 436.409035] RBP: ffff88013649bcc0 R08: 0000000000000001 R09: 0000000000000002 [ 436.409081] R10: ffff88013649bc40 R11: 0000000055555556 R12: 00000000001d9638 [ 436.409126] R13: 38ffffffa0261568 R14: 0000000000000000 R15: ffff880135273010 [ 436.409172] FS: 0000000000000000(0000) GS:ffff880028022000(0000) knlGS:0000000000000000 [ 436.409232] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b [ 436.409274] CR2: 00007fff925e4cd8 CR3: 000000013642a000 CR4: 00000000000406f0 [ 436.409320] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 436.409365] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 436.409411] Process kdvb-ad-2-fe-0 (pid: 1410, threadinfo ffff88013649a000, task ffff88013658ad60) [ 436.409473] Stack: [ 436.409508] ffff880136ee2af1 00000000bcd5d166 ffff000200000068 0000000035273000 [ 436.409608] <0> 0000000000000001 ffff880135273000 ffffffffa0265260 00003473bc000000 [ 436.409758] <0> 0000000000000000 ffff88013a4e05e0 ffff88013649bd00 ffffffffa025f133 [ 436.409938] Call Trace: [ 436.409978] [<ffffffffa025f133>] tda8261_set_frequency+0x23/0x70 [budget_av] [ 436.410027] [<ffffffffa026ed09>] ? stb0899_i2c_gate_ctrl+0x49/0xf0 [stb0899] [ 436.410074] [<ffffffffa026e259>] ? stb0899_write_reg+0x19/0x20 [stb0899] [ 436.410121] [<ffffffffa02716e2>] stb0899_dvbs_algo+0x3a2/0x13c8 [stb0899] [ 436.410170] [<ffffffff813cdd0d>] ? i2c_transfer+0xbd/0x100 [ 436.410215] [<ffffffffa026e13c>] ? stb0899_write_regs+0xac/0x1b0 [stb0899] [ 436.410262] [<ffffffffa026f239>] stb0899_search+0x489/0x750 [stb0899] [ 436.410308] [<ffffffff8107d153>] ? down_interruptible+0x33/0x60 [ 436.410360] [<ffffffffa00c34ec>] dvb_frontend_thread+0x57c/0x720 [dvb_core] [ 436.410407] [<ffffffff81078620>] ? autoremove_wake_function+0x0/0x40 [ 436.410457] [<ffffffffa00c2f70>] ? dvb_frontend_thread+0x0/0x720 [dvb_core] [ 436.410504] [<ffffffff81078236>] kthread+0xa6/0xb0 [ 436.410547] [<ffffffff810130aa>] child_rip+0xa/0x20 [ 436.410589] [<ffffffff81078190>] ? kthread+0x0/0xb0 [ 436.410631] [<ffffffff810130a0>] ? child_rip+0x0/0x20 [ 436.410672] Code: 00 03 00 00 4c 8b 6b 10 c7 45 cc 00 00 00 00 0f 84 e8 01 00 00 44 8b 22 41 8d 84 24 10 81 f1 ff 3d 80 4f 12 00 0f 87 af 01 00 00 <41> 8b 75 04 31 d2 48 c7 c7 d8 46 02 a0 89 f0 8b 0c 85 f0 45 02 [ 436.411950] RIP [<ffffffffa00241a1>] tda8261_set_state+0x51/0x250 [tda8261] [ 436.412015] RSP <ffff88013649bc70> [ 436.412064] ---[ end trace c1d7ae4d9e05c51b ]--- Signed-off-by:
Arvo Järve <arvo@softshark.ee> Signed-off-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
Oliver Endriss authored
Add parameters adc1_range, adc2_range and tuner_bbgain to the config struct. Defaults: adc1_range = adc2_range = 2Vpp, tuner_bbgain = 10db Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
Manu Abraham <abraham.manu@gmail.com> Signed-off-by:
-
Oliver Endriss authored
Exit stv090x_algo() if the tuner did not lock. This might happen due to missing signal or invalid/incomplete tuning parameters. Signed-off-by:
-
Oliver Endriss authored
The I2C gate must also be disabled, if a tuner command failed. Otherwise the tuner mutex would be locked forever. Signed-off-by:
-
Andreas Regel authored
When mclk is not 0 then it will never be set to the correct value and the Demodulator will not work. Signed-off-by:
Andreas Regel <andreas.regel@gmx.de> Signed-off-by:
-
Andreas Regel authored
This gives the STV090x and improved clock signal (rectangle instead of sine). Signed-off-by:
-
Andreas Regel authored
Using clk_div member of stv6110x_config structure the tuner's clock output divider can be configured. It is set in stv6110x_attach. Signed-off-by:
-
Andreas Regel authored
This is needed when clock input is driven from tuner and an output divider different from 1 is used. Signed-off-by:
-
Andreas Regel authored
Before there was used a static register map that could lead to issues when there are are multiple adapters with the STV6110(A). Signed-off-by:
-
Andreas Regel authored
The function stv6110x_write_regs is used to write several registers at once. Signed-off-by:
-
Andreas Regel authored
This could be useful for p.e. Common Interface applications where data rate is limited. Signed-off-by:
-
Andreas Regel authored
Signed-off-by:
-
Andreas Regel authored
Signed-off-by:
-
Andreas Regel authored
With this change it is possible to have the same I2C address for both tuners. Signed-off-by:
-
Andreas Regel authored
As the STV0900 features two demodulation paths in one chip there is some information used by both instances of the driver when used in dual mode. This information is now shared in an internal structure referenced by I2C adapter and address. Do initialisation of the demodulator only once when used in dual mode. Moved global mutex demod_lock to internal structure. Moved dev_ver and mclk to internal structure. Removed unused tuner_refclk from stv090x_state. Signed-off-by:
-
Andreas Regel authored
In automatic S/S2 detection mode, locking of a DVB-S transponder could fail when coming from a DVB-S2 transponder. This change fixes the issue by first disabling DVB-S and DVB-S2 mode before enabling it again. Signed-off-by:
-
Abylay Ospan authored
22-kHz tone can be driven in two ways: 1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is always activated ). 2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0. From LNBH24 datasheet: "In order to improve design flexibility an external tone input pin is available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz tone output, on the VoTX pin, by using the LNBH24 integrated tone generator (similar to the DSQIN pin function). In fact, the output tone waveform characteristics will always be internally controlled by the LNBH24 tone generator and the EXTM signal will be used as a timing control for DiSEqC tone data encoding on the VoTX output." In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by STV0900 demod: .set_tone = stv0900_set_tone redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual DVB-S2-CI card". Signed-off-by: -
Jean-Francois Moine authored
The two sensors ov772x and ov965x have too much differences. Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Peter Huewe authored
Trivial patch which adds the __init/__exit macros to the module_init/ module_exit functions of drivers/media/dvb/bt8xx/bt878.c Please have a look at the small patch and either pull it through your tree, or please ack' it so Jiri can pull it through the trivial tree. Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009 but also present in linus tree. Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Acked-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Joe Perches authored
And a little code refactoring/neatening around the removals Reduces object size a little bit: new: $ size drivers/media/dvb/frontends/si21xx.o text data bss dec hex filename 8984 56 1816 10856 2a68 drivers/media/dvb/frontends/si21xx.o old: $ size drivers/media/dvb/frontends/si21xx.o text data bss dec hex filename 9084 56 1792 10932 2ab4 drivers/media/dvb/frontends/si21xx.o Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Jiri Slaby authored
Stanse found a potential null dereference in cx18_dvb_start_feed and cx18_dvb_stop_feed. There is a check for stream being NULL, but it is dereferenced earlier. Move the dereference after the check. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Reviewed-by:
Andy Walls <awalls@radix.net> Acked-by:
-
Alexander Beregalov authored
Free ir_dev before exit. Found by cppcheck. Signed-off-by:
Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by:
-
Jiri Slaby authored
Stanse found an unreachable statement in zl10039_attach. There is a `break' followed by `goto error'. Remove that break, so that it can handle the error. Cc: Igor M. Liplianin <liplianin@me.by> Signed-off-by:
-
Jiri Slaby authored
Stanse found a memory leak in tuner_probe. It is not freed/assigned on all paths. Fix that. Signed-off-by:
-
Jiri Slaby authored
Stanse found a memory leak in smscore_gpio_configure. buffer is not freed/assigned on all paths. Fix that. Signed-off-by:
-
Roel Kluin authored
The return of saa7164_i2caddr_to_reglen() was not tested. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Francesco Lavra authored
this patch fixes a memory leak which occurs when an em28xx card with DVB extension is unplugged or its DVB extension driver is unloaded. In dvb_fini(), dev->dvb must be freed before being set to NULL, as is done in dvb_init() in case of error. Note that this bug is also present in the latest stable kernel release. Signed-off-by:
Francesco Lavra <francescolavra@interfree.it> Signed-off-by:
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
Francesco Lavra authored
This patch fixes the declaration of the sysfs attributes for IR's, which must be a NULL-terminated array of struct attribute *. Without this patch, my machine crashes when inserting a DVB card. Signed-off-by:
-
Dan Carpenter authored
I was initially concerned about the weird array index (the 2 bumps into the next row of the array). Matthias Schwarzott look at the datasheet and it turns out it should be zl10036_init_tab[1][0] |= 0x01; Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
Julia Lawall authored
Test the just-allocated value for NULL rather than some other value. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ identifier f; @@ f(...) { <+... return NULL; ...+> } @@ expression *x; expression y; identifier r.f; statement S; @@ x = f(...); ( if ((x) == NULL) S | if ( - y + x == NULL) S ) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Stefan Richter authored
If there is ever going to be a FireDTV or FloppyDTV firmware which does not provide a minimal ASCII textual descriptor for Model_Id --- or if the descriptor is provided indirectly in a descriptor directory --- the ieee1394 variant of the device probe of firedtv would dereference a NULL pointer. The firewire variant of firedtv's device probe is not affected. The fix makes sure that such an unexpected firmware is safely recognized by fdtv_alloc as an unknown firmware. Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
