- 27 Jun, 2005 40 commits
-
-
Alan Stern authored
This patch adds support to dummy_hcd for suspending and resuming the root hub and the emulated platform devices. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
This patch fixes the byte-ordering issue for setup packets in the dummy_hcd driver and cleans up a few things that sparse -Wbitwise dislikes. Signed-off-by:
-
Duncan Sands authored
you seem to have applied the original, not the new improved one with whiter teeth that uses kcalloc instead of kmalloc + memset. Here's a patch that goes on top of the one you applied. Signed-off-by:
Duncan Sands <baldrick@free.fr> Signed-off-by:
-
Andrew Morton authored
Work around the gcc-2.95.x macro expansion bug. Cc: Duncan Sands <baldrick@free.fr> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Duncan Sands authored
Zero the entire instance, not just the struct usbatm_data head. Make sure the just allocated urb is freed if we fail to allocate a buffer. Based on a patch by Stanislaw W. Gruszka. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Duncan Sands authored
Reduce the number of "unknown vpi/vci" debug messages to (usually) at most one per-urb, rather than one per-cell. This is only an issue when (a) many packets come in but no connection is open; and (b) CONFIG_USB_DEBUG is set. Signed-off-by:
-
Duncan Sands authored
Makefile and Kconfig entries for the new drivers. Signed-off-by:
-
Duncan Sands authored
Doesn't do any firmware loading etc, just transmission and reception. The user needs to take care of modem initialization, and load the module with parameters giving the endpoints to use and so forth. Signed-off-by:
-
Duncan Sands authored
Driver for modems based on the Conexant AccessRunner chipset. Original patch by Josep Comas, much reworked by Roman Kagan. Signed-off-by:
-
Duncan Sands authored
Port the speedtch driver to the new usbatm core. The code is much the same as before, just reorganized, though I threw in some minor improvements (a new module parameter for choosing the altsetting, more robust urb failure handling, ...) while I was there. Signed-off-by:
-
Andrew Morton authored
Signed-off-by:
-
Duncan Sands authored
Rework the core usbatm code: minidrivers (i.e. drivers for particular modems) now register themselves with the usbatm core, supplying methods for binding/unbinding etc. The design was inspired by usb-serial and usbnet. At the same time, more common code from the speedtch and cxacru (patch 3/5) drivers was generalized and moved into the core. The transmission and reception parts have been unified and simplified. Since this is a major change and I don't like underscores in file names, usb_atm.[ch] has been renamed usbatm.[ch]. Many thanks to Roman Kagan, who did a lot of the coding. Signed-off-by:
-
David Brownell authored
Various minor EHCI updates * Dump some more info in the debug dumps, notably the product description (e.g. chip vendor), BIOS handhake flags, and debug port status (when it's not managed by the HCD). * Minor updates to the BIOS handoff code: always flag the HCD as owned by Linux (in case BIOS doesn't grab it "early"), and on the buggy-BIOS path always match the "early handoff" code and forcibly disable SMI IRQs. * For the disabled 64bit DMA support, there's now a constant to use for the mask; use it. Signed-off-by:David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
David Brownell authored
This has several small updates to the px2xx UDC driver: * small fixes from Eugeny S. Mints <emints@ru.mvista.com> - local_irq_save() around potential endpoint disable race - fix handling of enqueue to OUT endpoints (potential oops) * add shutdown() method to disable any D+ pullup * rename methods accessing raw signals, referencing the signals * describes itself as for "pxa25x", since pxa27x is different Signed-off-by: -
David Brownell authored
Sparse updates; and the API change for SETUP packets being in USB byteorder. Signed-off-by:
-
David Brownell authored
This is mostly "sparse" related updates, one of which was a missing le32_to_cpu() should have affected big-endian hardware. Notable is the API change: setup packets are now provided in USB byte order. This affects only big-endian hardware, and the gadget drivers have been updated in a separate patch. Signed-off-by:
-
David Brownell authored
This updates most of the gadget framework to expect SETUP packets use USB byteorder (matching the annotation in <linux/usb_ch9.h> and usage in the host side stack): - definition in <linux/usb_gadget.h> - gadget drivers: Ethernet/RNDIS, serial/ACM, file_storage, gadgetfs. - dummy_hcd It also includes some other similar changes as suggested by "sparse", which was used to detect byteorder bugs. Signed-off-by:
-
David Brownell authored
This prevents gadget drivers from being selected when no controller has been selected, by adding an additional boolean and depending on it. It's mostly to help "allmodconfig". Signed-off-by:
-
Florian Echtler authored
Signed-off-by:
Florian Echtler <echtler@fs.tum.de> Signed-off-by:
Andreas Deresch <aderesch@fs.tum.de> Signed-off-by:
-
Alan Stern authored
This patch makes the dummy_hcd driver use emulated root-hub interrupts instead of polling. It's in the spirit of similar changes being made to the other HCDs. Signed-off-by:
-
Alan Stern authored
This patch adds to the dummy_hcd driver a new routine for keeping track of all changes in the state of the emulated USB link. The logic is now kept in one spot instead of spread around, and it's easier to verify and update the code. The behavior of the port features has been corrected in a few respects as well (for instance, if the POWER feature is clear then none of the other features can be set). Also added is support for the (relatively new) _connect() and _disconnect() calls of the Gadget API. Signed-off-by:
-
Alan Stern authored
This patch makes the dummy_hcd driver create separate platform devices for the emulated host controller and emulated device controller. This gives a more accurate simulation and will permit testing of situations where only one of the two devices is suspended. This also changes the name of the host controller platform device to match the name of the driver. That way the normal platform bus probe mechanism will handle binding the driver to the device. Signed-off-by:
-
Alan Stern authored
This patch makes some cosmetic changes to dummy_hcd: Minor alterations of comments and whitespace. Replace USB_PORT_FEAT_xxx with USB_PORT_STAT_xxx. This is appropriate as the values are stored in a status variable and they aren't feature indices. Also it allows the elimination of a bunch of awkward bit shift operations. Signed-off-by:
-
Alan Stern authored
Partial OTG support for dummy_hcd, mostly as a framework for further work. It emulates the new OTG flags in the host and peripheral frameworks, if that option is configured. But it's incomplete: - Resetting the peripheral needs to clear the OTG state bits; a second enumeration won't work correctly. - This stops modeling HNP right when roles should switch the first time. It should probably disconnect, then set the usb_bus.is_b_host and usb_gadget.is_a_peripheral flags; then it'd enumerate almost normally, except for the role reversal. Roles could then switch a second time, back to "normal" (with those flags cleared). - SRP should be modeled as "resume from port-unpowered", which is a state that usbcore doesn't yet use. HNP can be triggered by enabling the OTG whitelist and configuring a gadget driver that's not in that list; or by configuring Gadget Zero to identify itself as the HNP test device. Sent-by:David Brownell <david-b@pacbell.net> Signed-off-by:
-
David Brownell authored
More omap_udc updates: * OMAP 1710 updates - new UDC bit for clearing endpoint toggle, affecting CLEAR_HALT - new OTG bits affecting wakeup * Fix the bug Vladimir noted, that IN-DMA transfer code path kicks in for under 1024 bytes (not "up to 1024 bytes") * Handle transceiver setup more intelligently - use transceiver whenever one's available; this can be handy for GPIO based, loopback, or transceiverless configs - cleanup correctly after the "unrecognized HMC" case * DMA performance tweaks - allow burst/pack for memory access - use 16 bit DMA access most of the time on TIPB * Add workarounds for some DMA errata (not observed "in the wild"): - DMA CSAC/CDAC reads returning zero - RX/TX DMA config registers bit 12 always reads as zero (TI patch) * More "sparse" warnings removed, notably "changing" the SETUP packet to return data in USB byteorder (an API change, null effect on OMAP except for these warnings). Signed-off-by: -
David Brownell authored
Some cleanup for the the Ethernet part of the Ethernet/RNDIS gadget driver: - Remove remnants of ancient endpoint init logic; this is simpler, clearer - Save a smidgeon of space in the object file - Get rid of some #ifdeffery, mostly by using some newish inlines - Reset more driver state as part of USB reset - Remove a needless wrapper around an RNDIS call - Improve and comment the status interrupt handling: * RNDIS sometimes needs to queue these transfers (rarely in normal cases, but reproducibly while Windows was deadlocking its USB stack) * Mark requests as busy/not - Enable the SET_NETDEV_DEV() call; sysfs seems to behave sanely now This is a net shrink of source code. Signed-off-by: -
David Brownell authored
Some bugfixes and lots of cleanup (net code shrink): - On reset, force the RNDIS state machine its initial state - Hook up the RNDIS (outgoing) filters to the CDC mechanism - Lots of cleanup: * Eliminate duplicate copy of OID table; * Unify handlying of the OID "query" response data pointer; * Reduce code duplication for calculating query response lengths; * Remove some checks for "can't happen" errors; * Get rid of debugging #ifdefs by making the debug flag an integer level Most of the patch, by volume, relates to those query response cleanups. It incidentally shaves off a few hundred bytes of object code. Signed-off-by: -
Alan Stern authored
This patch changes the host controller drivers; they no longer need to register their root hubs because usbcore will take care of it for them. Signed-off-by:
-
Alan Stern authored
This patch makes usbcore automatically allocate and register the root hub device for a new host controller when the controller is registered. This way the HCDs don't all have to include the same boilerplate code. As a pleasant side benefit, the register_root_hub routine can now be made static and not EXPORTed. Signed-off-by:
-
Alan Stern authored
This patch changes the HCDs that used the old hub_set_power_budget call, making them use the new hcd->power_budget field instead. Signed-off-by:
-
Alan Stern authored
This patch simplifies the uhci-hcd driver by removing the device pointer currently stored in the QH and TD structures. Those pointers weren't being used for anything other than to increment the device's reference count, which is unnecessary since the device is used only when an URB completes, and outstanding URBs take their own reference to the device. As a useful side effect, this change means that uhci-hcd no longer needs to have the root-hub device available in the start routine. Signed-off-by:
-
Alan Stern authored
This patch removes the hub_set_power_budget routine, which was used by a couple of HCDs to indicate that the root hub was running on battery power. In its place is a new field added to struct usb_hcd, which HCDs can set before the root hub is registered. Special-case code in the hub driver knows to look at this field when configuring a root hub. Signed-off-by:
-
Colin Leroy authored
My patch adding PM support for zd1201 didn't check for the device on resume, which can oops if the device has been removed. This patch fixes it. Signed-off-by:
Colin Leroy <colin@colino.net> Signed-off-by:
-
Colin Leroy authored
This patch enables power management (suspend, resume) support for zd1201. It fixes problems after wakeup for me, but these problems did not appear everytime without this patch. it's a bit empirical, based on what the usbnet does, so maybe not correct... Maybe someone can give it a look before it's applied. Signed-off-by:
-
Greg Kroah-Hartman authored
[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used. This removes a lot of racy and buggy code by trying to check the status of the urb. Signed-off-by: -
David Brownell authored
Adds a reboot notifier to OHCI, mostly to benefit kexec; plus minor #include tweaks. Signed-off-by:
-
David Brownell authored
Updates to "usbtest" driver: * Improve some diagnostics. One path that never generated diagnostics before should now generate two ... unless you hit a GCC bug that all my compilers seem to have, go figure. * Add suspend/resume support, so this behaves when the Linux host being used for testing suspends. * Don't test the "zero byte ep0 read" case unless real-world relevance for the testing is is irrelevant. Signed-off-by: -
Oliver Neukum authored
This patch fixes lost LF when ACM device is used with getty/login/bash, in case of a modem which takes calls. Signed-off-by:
Oliver Neukum <oliver@neukum.name> Signed-off-by:
-
Alan Stern authored
This is a revised version of an earlier patch to add support to usbcore for driving root hubs by interrupts rather than polling. There's a temporary flag added to struct usb_hcd, marking devices whose drivers are aware of the new mechanism. By default that flag doesn't get set so drivers will continue to see the same polling behavior as before. This way we can convert the HCDs one by one to use interrupt-based event reporting, and the temporary flag can be removed when they're all done. Also included is a small change to the hcd_disable_endpoint routine. Although endpoints normally shouldn't be disabled while a controller is suspended, it's legal to do so when the controller's driver is being rmmod'ed. Lastly the patch adds a new callback, .hub_irq_enable, for use by HCDs where the root hub's port-change interrupts are level-triggered rather than edge-triggered. The callback is invoked each time khubd has finished processing a root hub, to let the HCD know that the interrupt can safely be re-enabled. Signed-off-by:
-
Alan Stern authored
After all the discussion you might not be interested in this still, but nevertheless here it is. This patch adds a shutdown method to the uhci-hcd driver. Its prerequisite is the patch you wrote adding shutdown support for PCI. Signed-off-by:
-
